Ticket #957: smartctl-Seagate-ST6000NM0095.txt

File smartctl-Seagate-ST6000NM0095.txt, 4.4 KB (added by Stefan, 6 years ago)
Line 
1./smart-pkg/usr/local/sbin/smartctl -x /dev/sdz
2smartctl 6.7 2017-12-07 r4648 [x86_64-linux-4.9.0-3-amd64] (local build)
3Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
4
5=== START OF INFORMATION SECTION ===
6Vendor: SEAGATE
7Product: ST6000NM0095
8Revision: E002
9Compliance: SPC-4
10User Capacity: 6,001,175,126,016 bytes [6.00 TB]
11Logical block size: 512 bytes
12Physical block size: 4096 bytes
13LU is fully provisioned
14Rotation Rate: 7200 rpm
15Form Factor: 3.5 inches
16Logical Unit id: 0x5000c500944259d3
17Serial number: ZAD1W11S0000C75039MN
18Device type: disk
19Transport protocol: SAS (SPL-3)
20Local Time is: Thu Dec 14 09:45:56 2017 CET
21SMART support is: Available - device has SMART capability.
22SMART support is: Enabled
23Temperature Warning: Enabled
24Read Cache is: Enabled
25Writeback Cache is: Enabled
26
27=== START OF READ SMART DATA SECTION ===
28SMART Health Status: OK
29
30Current Drive Temperature: 33 C
31Drive Trip Temperature: 60 C
32
33Manufactured in week 27 of year 2017
34Specified cycle count over device lifetime: 10000
35Accumulated start-stop cycles: 55
36Specified load-unload count over device lifetime: 300000
37Accumulated load-unload cycles: 12790
38Elements in grown defect list: 0
39
40Vendor (Seagate) cache information
41 Blocks sent to initiator = 67400
42 Blocks received from initiator = 46792
43 Blocks read from cache and sent to initiator = 342614
44 Number of read and write commands whose size <= segment size = 240
45 Number of read and write commands whose size > segment size = 0
46
47Vendor (Seagate/Hitachi) factory information
48 number of hours powered up = 2580.37
49 number of minutes until next internal SMART test = 5
50
51Error counter log:
52 Errors Corrected by Total Correction Gigabytes Total
53 ECC rereads/ errors algorithm processed uncorrected
54 fast | delayed rewrites corrected invocations [10^9 bytes] errors
55read: 60100 0 0 60100 0 0.035 0
56write: 0 0 0 0 0 1.133 0
57
58Non-medium error count: 21
59
60
61[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
62SMART Self-test log
63Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
64 Description number (hours)
65# 1 Background short Completed - 2579 - [- - -]
66
67Long (extended) Self Test duration: 29880 seconds [498.0 minutes]
68
69Background scan results log
70 Status: no scans active
71 Accumulated power on time, hours:minutes 2580:22 [154822 minutes]
72 Number of background scans performed: 0, scan progress: 0.00%
73 Number of background medium scans performed: 0
74
75Protocol Specific port log page for SAS SSP
76relative target port id = 1
77 generation code = 0
78 number of phys = 1
79 phy identifier = 0
80 attached device type: expander device
81 attached reason: SMP phy control function
82 reason: loss of dword synchronization
83 negotiated logical link rate: phy enabled; 12 Gbps
84 attached initiator port: ssp=0 stp=0 smp=0
85 attached target port: ssp=0 stp=0 smp=1
86 SAS address = 0x5000c500944259d1
87 attached SAS address = 0x5003048009101a7f
88 attached phy identifier = 36
89 Invalid DWORD count = 0
90 Running disparity error count = 0
91 Loss of DWORD synchronization = 1
92 Phy reset problem = 0
93 Phy event descriptors:
94 Invalid word count: 0
95 Running disparity error count: 0
96 Loss of dword synchronization count: 1
97 Phy reset problem count: 0
98relative target port id = 2
99 generation code = 0
100 number of phys = 1
101 phy identifier = 1
102 attached device type: expander device
103 attached reason: SMP phy control function
104 reason: unknown
105 negotiated logical link rate: phy enabled; 12 Gbps
106 attached initiator port: ssp=0 stp=0 smp=0
107 attached target port: ssp=0 stp=0 smp=1
108 SAS address = 0x5000c500944259d2
109 attached SAS address = 0x5003048009101aff
110 attached phy identifier = 36
111 Invalid DWORD count = 0
112 Running disparity error count = 0
113 Loss of DWORD synchronization = 2
114 Phy reset problem = 0
115 Phy event descriptors:
116 Invalid word count: 0
117 Running disparity error count: 0
118 Loss of dword synchronization count: 2
119 Phy reset problem count: 0
120