./smart-pkg/usr/local/sbin/smartctl -x /dev/sdz 
smartctl 6.7 2017-12-07 r4648 [x86_64-linux-4.9.0-3-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST6000NM0095
Revision:             E002
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   512 bytes
Physical block size:  4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c500944259d3
Serial number:        ZAD1W11S0000C75039MN
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Dec 14 09:45:56 2017 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     33 C
Drive Trip Temperature:        60 C

Manufactured in week 27 of year 2017
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  55
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  12790
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 67400
  Blocks received from initiator = 46792
  Blocks read from cache and sent to initiator = 342614
  Number of read and write commands whose size <= segment size = 240
  Number of read and write commands whose size > segment size = 0

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2580.37
  number of minutes until next internal SMART test = 5

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:      60100        0         0     60100          0          0.035           0
write:         0        0         0         0          0          1.133           0

Non-medium error count:       21


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2579                 - [-   -    -]

Long (extended) Self Test duration: 29880 seconds [498.0 minutes]

Background scan results log
  Status: no scans active
    Accumulated power on time, hours:minutes 2580:22 [154822 minutes]
    Number of background scans performed: 0,  scan progress: 0.00%
    Number of background medium scans performed: 0

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 0
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: loss of dword synchronization
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000c500944259d1
    attached SAS address = 0x5003048009101a7f
    attached phy identifier = 36
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 1
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 1
     Phy reset problem count: 0
relative target port id = 2
  generation code = 0
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000c500944259d2
    attached SAS address = 0x5003048009101aff
    attached phy identifier = 36
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 2
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 2
     Phy reset problem count: 0