== smartctl report for HTS547550A9E384 == === Command === Access via AHCI controller: {{{smartctl -x -q noserial ..}}} === Output === {{{ smartctl 6.5 2016-05-07 r4318 [FreeBSD 10.3-RELEASE-p16 amd64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar 5K750 Device Model: Hitachi HTS547550A9E384 Firmware Version: JE3OA40J User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Mar 14 15:19:01 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 152) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 197 197 040 - 160 3 Spin_Up_Time POS--- 211 211 033 - 1 4 Start_Stop_Count -O--C- 100 100 000 - 59 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 120 120 040 - 32 9 Power_On_Hours -O--C- 001 001 000 - 53400 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 58 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 9 193 Load_Cycle_Count -O--C- 001 001 000 - 14907336 194 Temperature_Celsius -O---- 222 222 000 - 27 (Min/Max 12/48) 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 02 -- 51 00 00 00 00 00 00 00 00 00 00 Error: TK0NF Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 10 00 00 00 01 00 00 00 00 03 34 e0 ff 00:00:17.305 RECALIBRATE [OBS-4] 10 00 00 00 01 00 00 00 00 03 34 e0 08 00:00:17.138 RECALIBRATE [OBS-4] 91 40 00 01 3f 00 00 01 00 03 34 af 08 00:00:17.138 INITIALIZE DEVICE PARAMETERS [OBS-6] c4 00 40 00 00 00 00 3f 00 00 00 e0 04 00:00:16.934 READ MULTIPLE c4 00 40 00 01 00 00 3f 00 00 00 e0 00 00:00:07.959 READ MULTIPLE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 43116 - # 2 Extended offline Completed without error 00% 29867 - # 3 Extended offline Completed without error 00% 19477 - # 4 Extended offline Completed without error 00% 13675 - # 5 Extended offline Completed without error 00% 10202 - # 6 Extended offline Completed without error 00% 5334 - # 7 Extended offline Completed without error 00% 4764 - # 8 Extended offline Completed without error 00% 2322 - # 9 Extended offline Completed without error 00% 25 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 15/38 Celsius Lifetime Min/Max Temperature: 12/48 Celsius Lifetime Average Temperature: 26 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 15 minutes Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (94) Index Estimated Time Temperature Celsius 95 2017-03-13 07:30 26 ******* 96 2017-03-13 07:45 25 ****** 97 2017-03-13 08:00 26 ******* 98 2017-03-13 08:15 25 ****** 99 2017-03-13 08:30 25 ****** 100 2017-03-13 08:45 26 ******* ... ..( 9 skipped). .. ******* 110 2017-03-13 11:15 26 ******* 111 2017-03-13 11:30 27 ******** 112 2017-03-13 11:45 27 ******** 113 2017-03-13 12:00 26 ******* 114 2017-03-13 12:15 26 ******* 115 2017-03-13 12:30 27 ******** 116 2017-03-13 12:45 26 ******* ... ..( 2 skipped). .. ******* 119 2017-03-13 13:30 26 ******* 120 2017-03-13 13:45 27 ******** 121 2017-03-13 14:00 26 ******* 122 2017-03-13 14:15 26 ******* 123 2017-03-13 14:30 26 ******* 124 2017-03-13 14:45 27 ******** 125 2017-03-13 15:00 26 ******* 126 2017-03-13 15:15 26 ******* 127 2017-03-13 15:30 27 ******** 0 2017-03-13 15:45 27 ******** 1 2017-03-13 16:00 26 ******* 2 2017-03-13 16:15 27 ******** 3 2017-03-13 16:30 27 ******** 4 2017-03-13 16:45 27 ******** 5 2017-03-13 17:00 26 ******* 6 2017-03-13 17:15 26 ******* 7 2017-03-13 17:30 26 ******* 8 2017-03-13 17:45 27 ******** ... ..( 6 skipped). .. ******** 15 2017-03-13 19:30 27 ******** 16 2017-03-13 19:45 26 ******* 17 2017-03-13 20:00 26 ******* 18 2017-03-13 20:15 26 ******* 19 2017-03-13 20:30 27 ******** 20 2017-03-13 20:45 27 ******** 21 2017-03-13 21:00 26 ******* 22 2017-03-13 21:15 27 ******** 23 2017-03-13 21:30 27 ******** 24 2017-03-13 21:45 26 ******* ... ..( 3 skipped). .. ******* 28 2017-03-13 22:45 26 ******* 29 2017-03-13 23:00 27 ******** 30 2017-03-13 23:15 26 ******* 31 2017-03-13 23:30 27 ******** 32 2017-03-13 23:45 26 ******* 33 2017-03-14 00:00 26 ******* 34 2017-03-14 00:15 26 ******* 35 2017-03-14 00:30 27 ******** 36 2017-03-14 00:45 27 ******** 37 2017-03-14 01:00 27 ******** 38 2017-03-14 01:15 26 ******* 39 2017-03-14 01:30 26 ******* 40 2017-03-14 01:45 27 ******** 41 2017-03-14 02:00 26 ******* ... ..( 8 skipped). .. ******* 50 2017-03-14 04:15 26 ******* 51 2017-03-14 04:30 27 ******** 52 2017-03-14 04:45 26 ******* ... ..( 36 skipped). .. ******* 89 2017-03-14 14:00 26 ******* 90 2017-03-14 14:15 27 ******** 91 2017-03-14 14:30 26 ******* 92 2017-03-14 14:45 27 ******** 93 2017-03-14 15:00 26 ******* 94 2017-03-14 15:15 27 ******** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 58 --- Lifetime Power-On Resets 0x01 0x010 4 53400 --- Power-on Hours 0x01 0x018 6 10920695850 --- Logical Sectors Written 0x01 0x020 6 190751879 --- Number of Write Commands 0x01 0x028 6 11545163847 --- Logical Sectors Read 0x01 0x030 6 39023365 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 17557 --- Spindle Motor Power-on Hours 0x03 0x010 4 16408 --- Head Flying Hours 0x03 0x018 4 14907336 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 4070 --- Read Recovery Attempts 0x03 0x030 4 3 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 358 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 27 --- Current Temperature 0x05 0x010 1 26 N-- Average Short Term Temperature 0x05 0x018 1 25 N-- Average Long Term Temperature 0x05 0x020 1 48 --- Highest Temperature 0x05 0x028 1 12 --- Lowest Temperature 0x05 0x030 1 40 N-- Highest Average Short Term Temperature 0x05 0x038 1 14 N-- Lowest Average Short Term Temperature 0x05 0x040 1 38 N-- Highest Average Long Term Temperature 0x05 0x048 1 23 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 507 --- Number of Hardware Resets 0x06 0x010 4 288 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 62 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 46 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS }}}