ORICO USB3.0 2.5 inch External Hard Drive Enclosure (2588US3) works

[Almorca]

"ORICO USB3.0 2.5 inch External Hard Drive Enclosure (2588US3)" with a SSD OCZ Agility 3 works with -d sat

Product information

idVendor 0x0080
idProduct 0xa001
bcdDevice 2.03
iManufacturer 1 TOSHIBA
iProduct 2 External USB 3.0
iSerial 3 2015033100063

smartctl -a -d sat /dev/sdc

smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.8.0-56-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

START OF INFORMATION SECTION

Model Family: SandForce Driven SSDs
Device Model: OCZ-AGILITY3
Serial Number: OCZ-F9788Y01548UAA7B
LU WWN Device Id: 5 e83a97 effc3ffe7
Firmware Version: 2.15
User Capacity: 60.022.480.896 bytes [60,0 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS, ACS-2 T13/2015-D revision 3
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Jun 28 20:57:02 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

START OF READ SMART DATA SECTION

SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity

was never started.
Auto Offline Data Collection: Disabled.

Self-test execution status: ( 0) The previous self-test routine completed

without error or no self-test has ever
been run.

Total time to complete Offline
data collection: ( 2097) seconds.
Offline data collection
capabilities: (0x7f) SMART execute Offline immediate.

Auto Offline data collection on/off support.
Abort Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.

SMART capabilities: (0x0003) Saves SMART data before entering

power-saving mode.
Supports SMART auto save timer.

Error logging capability: (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 48) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x0021) SCT Status supported.

SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE

1 Raw_Read_Error_Rate 0x000f 120 120 050 Pre-fail Always - 0/0
5 Retired_Block_Count 0x0033 100 100 003 Pre-fail Always - 0
9 Power_On_Hours_and_Msec 0x0032 097 097 000 Old_age Always - 2848h+34m+33.520s

12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1293

171 Program_Fail_Count 0x0032 000 000 000 Old_age Always - 0
172 Erase_Fail_Count 0x0032 000 000 000 Old_age Always - 0
174 Unexpect_Power_Loss_Ct 0x0030 000 000 000 Old_age Offline - 35
177 Wear_Range_Delta 0x0000 000 000 000 Old_age Offline - 3
181 Program_Fail_Count 0x0032 000 000 000 Old_age Always - 0
182 Erase_Fail_Count 0x0032 000 000 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
194 Temperature_Celsius 0x0022 030 030 000 Old_age Always - 30 (Min/Max 30/30)
195 ECC_Uncorr_Error_Count 0x001c 100 100 000 Old_age Offline - 0/0
196 Reallocated_Event_Count 0x0033 100 100 003 Pre-fail Always - 0
201 Unc_Soft_Read_Err_Rate 0x001c 100 100 000 Old_age Offline - 0/0
204 Soft_ECC_Correct_Rate 0x001c 100 100 000 Old_age Offline - 0/0
230 Life_Curve_Status 0x0013 100 100 000 Pre-fail Always - 100
231 SSD_Life_Left 0x0013 100 100 010 Pre-fail Always - 0
233 SandForce_Internal 0x0000 000 000 000 Old_age Offline - 1567
234 SandForce_Internal 0x0032 000 000 000 Old_age Always - 2086
241 Lifetime_Writes_GiB 0x0032 000 000 000 Old_age Always - 2086
242 Lifetime_Reads_GiB 0x0032 000 000 000 Old_age Always - 5823

SMART Error Log not supported

SMART Self-test Log not supported

SMART Selective self-test log data structure revision number 1

SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS

1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing

Selective self-test flags (0x0):

After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.