Opened 4 years ago
Last modified 4 years ago
#1342 new defect
Prolific PL2507 (0x067b:0x2507) — at Initial Version
| Reported by: | floogy | Owned by: | |
|---|---|---|---|
| Priority: | minor | Milestone: | undecided |
| Component: | all | Version: | 7.1 |
| Keywords: | Cc: |
Description
Hi, I got an old "Lidl Targa" external USB Drive with a [usbjmicron] Prolific PL2507 (0x067b:0x2507) USB to IDE bridge and an 400GB SAMSUNG HD400LD HDD.
smartctl doesn't work very good on this one, despitze I found some reports it should, but maybe I got a different combination or configuration?
sat, auto gives better output than usbjmicron,0, but no smartoutput either.
-d sat,auto (full see at the end of the report)
{{{ [...]
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
Terminate command early due to bad response to IEC mode page
START OF ENABLE/DISABLE COMMANDS SECTION
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
unable to fetch IEC (SMART) mode page [scsi response fails sanity test]
START OF READ SMART DATA SECTION
Current Drive Temperature: 0 C
Drive Trip Temperature: 0 C
Error Counter logging not supported
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
Device does not support Self Test logging
}}}
-d test
~$ sudo smartctl -a -T verypermissive --smart=on -d test /dev/sdk smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-29-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org /dev/sdk [USB JMicron]: Device of type '**usbjmicron**' [ATA] detected /dev/sdk [USB JMicron]: Device of type 'usbjmicron' [ATA] opened
but usbmicron gives garbage (see bottom of this report)
Thank you in advance.
floogy
informations and tests
~$ uname -a
Linux ubuntu-SSD1 5.4.0-29-generic #33-Ubuntu SMP Wed Apr 29 14:32:27 UTC 2020 x86_64 x86_64 x86_64 GNU/Linux
~$ lsb_release -a
No LSB modules are available.
Distributor ID: Ubuntu
Description: Ubuntu 20.04 LTS
Release: 20.04
Codename: focal
~$ dpkg -l smartmontools | grep ^ii
ii smartmontools 7.1-1build1 amd64 control and monitor storage systems using S.M.A.R.T.
~$ apt policy smartmontools
smartmontools:
Installiert: 7.1-1build1
Installationskandidat: 7.1-1build1
Versionstabelle:
*** 7.1-1build1 500
500 http://de.archive.ubuntu.com/ubuntu focal/main amd64 Packages
100 /var/lib/dpkg/status
$ smartctl -V
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-29-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
smartctl comes with ABSOLUTELY NO WARRANTY. This is free
software, and you are welcome to redistribute it under
the terms of the GNU General Public License; either
version 2, or (at your option) any later version.
See http://www.gnu.org for further details.
smartmontools release 7.1 dated 2019-12-30 at 15:00:11 UTC
smartmontools SVN rev 5022 dated 2019-12-30 at 15:00:49
smartmontools build host: x86_64-pc-linux-gnu
smartmontools build with: C++14, GCC 9.3.0
smartmontools configure arguments: '--includedir=${prefix}/include' '--mandir=${prefix}/share/man' '--infodir=${prefix}/share/info' '--localstatedir=/var' '--disable-silent-rules' '--libdir=${prefix}/lib/x86_64-linux-gnu' '--runstatedir=/run' '--disable-maintainer-mode' '--disable-dependency-tracking' '--build=x86_64-linux-gnu' '--host=x86_64-linux-gnu' '--prefix=/usr' '--sysconfdir=/etc' '--mandir=/usr/share/man' '--with-initscriptdir=no' '--docdir=/usr/share/doc/smartmontools' '--with-attributelog=/var/lib/smartmontools/attrlog.' '--with-drivedbdir=/var/lib/smartmontools/drivedb' '--with-exampledir=/usr/share/doc/smartmontools/examples/' '--with-savestates=/var/lib/smartmontools/smartd.' '--with-smartdplugindir=/etc/smartmontools/smartd_warning.d' '--with-smartdscriptdir=/usr/share/smartmontools' '--with-systemdenvfile=/etc/default/smartmontools' '--with-systemdsystemunitdir=/lib/systemd/system' '--with-libsystemd=auto' '--with-selinux' 'build_alias=x86_64-linux-gnu' 'host_alias=x86_64-linux-gnu' 'CXXFLAGS=-g -O2 -fdebug-prefix-map=/build/smartmontools-ZttrSr/smartmontools-7.1=. -fstack-protector-strong -Wformat -Werror=format-security -fsigned-char -Wall -O2' 'LDFLAGS=-Wl,-Bsymbolic-functions -Wl,-z,relro -Wl,-z,now' 'CPPFLAGS=-Wdate-time -D_FORTIFY_SOURCE=2' 'CFLAGS=-g -O2 -fdebug-prefix-map=/build/smartmontools-ZttrSr/smartmontools-7.1=. -fstack-protector-strong -Wformat -Werror=format-security -fsigned-char -Wall -O2'
[...]
[59856.544333] perf: interrupt took too long (4962 > 4958), lowering kernel.perf_event_max_sample_rate to 40250
[67159.354847] usb 1-1.5.4: USB disconnect, device number 9
[67221.892015] usb 1-1.5.4: new high-speed USB device number 10 using ehci-pci
[67221.922552] usb 1-1.5.4: New USB device found, idVendor=067b, idProduct=2507, bcdDevice= 1.00
[67221.922555] usb 1-1.5.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[67221.922558] usb 1-1.5.4: Product: Mass Storage Device
[67221.922559] usb 1-1.5.4: Manufacturer: Prolific Technology Inc.
[67221.923069] usb-storage 1-1.5.4:1.0: USB Mass Storage device detected
[67221.923327] usb-storage 1-1.5.4:1.0: Quirks match for vid 067b pid 2507: 110
[67221.925284] scsi host10: usb-storage 1-1.5.4:1.0
[67222.936804] scsi 10:0:0:0: Direct-Access SAMSUNG HD400LD WQ10 PQ: 0 ANSI: 0
[67222.937235] sd 10:0:0:0: Attached scsi generic sg10 type 0
[67222.938035] sd 10:0:0:0: [sdk] Adjusting the sector count from its reported value: 781422769
[67222.938041] sd 10:0:0:0: [sdk] 781422768 512-byte logical blocks: (400 GB/373 GiB)
[67222.939145] sd 10:0:0:0: [sdk] Write Protect is off
[67222.939147] sd 10:0:0:0: [sdk] Mode Sense: 03 00 00 00
[67222.940262] sd 10:0:0:0: [sdk] No Caching mode page found
[67222.940268] sd 10:0:0:0: [sdk] Assuming drive cache: write through
[67222.961280] sd 10:0:0:0: [sdk] Adjusting the sector count from its reported value: 781422769
[67222.984199] sdk: sdk1 sdk2
[67222.985501] sd 10:0:0:0: [sdk] Adjusting the sector count from its reported value: 781422769
[67222.987775] sd 10:0:0:0: [sdk] Attached SCSI disk
[67223.350177] BTRFS warning (device sdj1): duplicate device fsid:devid for 898c8973-ae88-454d-b76b-c540660909d1:1 old:/dev/sdj1 new:/dev/sdk1
[67223.492522] BTRFS warning (device sdj1): duplicate device fsid:devid for 898c8973-ae88-454d-b76b-c540660909d1:1 old:/dev/sdj1 new:/dev/sdk1
floogy@ubuntu-SSD1:~$ lsusb | grep Prolific
Bus 001 Device 010: ID 067b:2507 Prolific Technology, Inc. PL2507 Hi-speed USB to IDE bridge controller
floogy@ubuntu-SSD1:~$ lsusb -d 67b:2507
Bus 001 Device 010: ID 067b:2507 Prolific Technology, Inc. PL2507 Hi-speed USB to IDE bridge controller
floogy@ubuntu-SSD1:~$ lsusb -v -d 67b:2507
Bus 001 Device 010: ID 067b:2507 Prolific Technology, Inc. PL2507 Hi-speed USB to IDE bridge controller
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x067b Prolific Technology, Inc.
idProduct 0x2507 PL2507 Hi-speed USB to IDE bridge controller
bcdDevice 1.00
iManufacturer 1
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0020
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
floogy@ubuntu-SSD1:~$
floogy@ubuntu-SSD1:~$ sudo smartctl -a -T verypermissive --smart=on -d sat,auto /dev/sdk
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-29-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: SAMSUNG
Product: HD400LD
Revision: WQ10
User Capacity: 400.088.457.728 bytes [400 GB]
Logical block size: 512 bytes
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
>> Terminate command early due to bad response to IEC mode page
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
unable to fetch IEC (SMART) mode page [scsi response fails sanity test]
=== START OF READ SMART DATA SECTION ===
Current Drive Temperature: 0 C
Drive Trip Temperature: 0 C
Error Counter logging not supported
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
Device does not support Self Test logging
floogy@ubuntu-SSD1:~$
floogy@ubuntu-SSD1:~$ sudo smartctl -a -T verypermissive --smart=on -d test /dev/sdk
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-29-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
/dev/sdk [USB JMicron]: Device of type 'usbjmicron' [ATA] detected
/dev/sdk [USB JMicron]: Device of type 'usbjmicron' [ATA] opened
auto gives garbage
floogy@ubuntu-SSD1:~$ sudo smartctl -a -T verypermissive --smart=on -d auto /dev/sdk
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-29-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
Read Device Identity failed: scsi error unsupported scsi opcode
=== START OF INFORMATION SECTION ===
Device Model: �u�ګ��_�Qz�����#��ـ:����3�D@����qm
Serial Number: @�����s�����I�V9
LU WWN Device Id: 8 28d498 0ce5074bf
Firmware Version: ���<���W
User Capacity: 1.697.303.176.704 bytes [1,69 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7168 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-4 (unknown minor revision code: 0xdf73)
Transport Type: Unknown (0x93a4)
Local Time is: Sun Jun 14 03:42:51 2020 CEST
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported.
SMART support is: Unknown - Try option -s with argument 'on' to enable it.
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enable failed: scsi error unsupported scsi opcode
Read SMART Data failed: scsi error unsupported scsi opcode
=== START OF READ SMART DATA SECTION ===
SMART Status command failed: scsi error unsupported scsi opcode
SMART overall-health self-assessment test result: UNKNOWN!
SMART Status, Attributes and Thresholds cannot be read.
Read SMART Error Log failed: scsi error unsupported scsi opcode
Read SMART Self-test Log failed: scsi error unsupported scsi opcode
Selective Self-tests/Logging not supported
floogy@ubuntu-SSD1:~$
_______________________________________________________________________________________
floogy@ubuntu-SSD1:~$ sudo smartctl -T verypermissive -x -d usbjmicron,x,0 /dev/sdk
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-29-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
Read Device Identity failed: scsi error unsupported scsi opcode
=== START OF INFORMATION SECTION ===
Device Model: [˟/����3o���k�%
Serial Number: ���u*��,K�B�0���
Firmware Version: E�)���^
User Capacity: 1.408.203.512.832 bytes [1,40 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 59160 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS >5 (14) (unknown minor revision code: 0xc997)
Transport Type: Unknown (0x8be5)
Local Time is: Sun Jun 14 04:09:31 2020 CEST
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported.
SMART support is: Unknown - Try option -s with argument 'on' to enable it.AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Unavailable
Write cache is: Unavailable
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable
Read SMART Data failed: scsi error unsupported scsi opcode
=== START OF READ SMART DATA SECTION ===
SMART Status command failed: scsi error unsupported scsi opcode
SMART overall-health self-assessment test result: UNKNOWN!
SMART Status, Attributes and Thresholds cannot be read.
Read SMART Log Directory failed: scsi error unsupported scsi opcode
ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: scsi error unsupported scsi opcode
Read GP Log Directory failed
SMART Extended Comprehensive Error Log (GP Log 0x03) not supported
Read SMART Error Log failed: scsi error unsupported scsi opcode
SMART Extended Self-test Log (GP Log 0x07) not supported
Read SMART Self-test Log failed: scsi error unsupported scsi opcode
Selective Self-tests/Logging not supported
SCT Commands not supported
Device Statistics (GP/SMART Log 0x04) not supported
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11) not supported
floogy@ubuntu-SSD1:~$
references
Smartmontools USB Device Support
Profilic 0x067b
(No Name) Prolific PL2507 0x067b:0x2507 ? -d usbjmicron,x Linux Ondrej Zary, also ML-Archive
https://www.smartmontools.org/wiki/Supported_USB-Devices#idVendor0x0500
[smartmontools-support] Recognizing Samsung HD400LD USB drive
From: bege <bege10@t-...> - 2016-10-19 12:15:25
https://sourceforge.net/p/smartmontools/mailman/message/35437231/
[smartmontools-support] Prolific PL2507 USB Device
From: James Olson <big_spender12@ly...> - 2012-04-27 00:56:50
Please move the Prolific PL2507 (0x067b:0x25070 USB Device from the Unsupported Devices section to the Supported Devices section of the Supported USB Devices page. It uses the jmicron protocol and works with the "smartctl -d usbjmicron,0" command. Note that you must supply the ,0 for the Port or you will get a failure with a "No device connected" message.
https://sourceforge.net/p/smartmontools/mailman/smartmontools-support/thread/1779131327.21974.1335487159222.JavaMail.mail@webmail15/
Note:
See TracTickets
for help on using tickets.
