not in db: HGST HUS726T6TALE6L4
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-43-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HGST HUS726T6TALE6L4
Serial Number: V8GX9YWR
LU WWN Device Id: 5 000cca 098ccdfcb
Firmware Version: VKGNW40H
User Capacity: 6,001,175,126,016 bytes [6.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Jan 19 12:58:02 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 87) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 676) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0
2 Throughput_Performance P-S--- 100 100 054 - 0
3 Spin_Up_Time POS--- 100 100 024 - 0
4 Start_Stop_Count -O--C- 100 100 000 - 2
5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
7 Seek_Error_Rate PO-R-- 100 100 067 - 0
8 Seek_Time_Performance P-S--- 100 100 020 - 0
9 Power_On_Hours -O--C- 100 100 000 - 2
10 Spin_Retry_Count PO--C- 100 100 060 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 2
192 Power-Off_Retract_Count -O--CK 100 100 000 - 2
193 Load_Cycle_Count -O--C- 100 100 000 - 2
194 Temperature_Celsius -O---- 146 146 000 - 41 (Min/Max 21/43)
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
197 Current_Pending_Sector -O---K 100 100 000 - 0
198 Offline_Uncorrectable ---R-- 100 100 000 - 0
199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x04 GPL R/O 256 Device Statistics log
0x04 SL R/O 255 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x0c GPL R/O 5501 Pending Defects log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x12 GPL R/O 1 SATA NCQ NON-DATA log
0x13 GPL R/O 1 SATA NCQ Send and Receive log
0x15 GPL R/W 1 SATA Rebuild Assist log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x24 GPL R/O 256 Current Device Internal Status Data log
0x25 GPL R/O 256 Saved Device Internal Status Data log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 0
Device State: Active (0)
Current Temperature: 41 Celsius
Power Cycle Min/Max Temperature: 33/43 Celsius
Lifetime Min/Max Temperature: 21/43 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -40/70 Celsius
Temperature History Size (Index): 128 (18)
Index Estimated Time Temperature Celsius
19 2019-01-19 10:51 32 *************
20 2019-01-19 10:52 32 *************
21 2019-01-19 10:53 32 *************
22 2019-01-19 10:54 33 **************
... ..( 2 skipped). .. **************
25 2019-01-19 10:57 33 **************
26 2019-01-19 10:58 34 ***************
27 2019-01-19 10:59 34 ***************
28 2019-01-19 11:00 34 ***************
29 2019-01-19 11:01 35 ****************
... ..( 3 skipped). .. ****************
33 2019-01-19 11:05 35 ****************
34 2019-01-19 11:06 36 *****************
... ..( 3 skipped). .. *****************
38 2019-01-19 11:10 36 *****************
39 2019-01-19 11:11 37 ******************
... ..( 6 skipped). .. ******************
46 2019-01-19 11:18 37 ******************
47 2019-01-19 11:19 38 *******************
... ..( 7 skipped). .. *******************
55 2019-01-19 11:27 38 *******************
56 2019-01-19 11:28 39 ********************
... ..( 13 skipped). .. ********************
70 2019-01-19 11:42 39 ********************
71 2019-01-19 11:43 40 *********************
72 2019-01-19 11:44 39 ********************
73 2019-01-19 11:45 40 *********************
... ..( 5 skipped). .. *********************
79 2019-01-19 11:51 40 *********************
80 2019-01-19 11:52 41 **********************
... ..( 5 skipped). .. **********************
86 2019-01-19 11:58 41 **********************
87 2019-01-19 11:59 42 ***********************
... ..( 6 skipped). .. ***********************
94 2019-01-19 12:06 42 ***********************
95 2019-01-19 12:07 43 ************************
... ..( 20 skipped). .. ************************
116 2019-01-19 12:28 43 ************************
117 2019-01-19 12:29 42 ***********************
... ..( 19 skipped). .. ***********************
9 2019-01-19 12:49 42 ***********************
10 2019-01-19 12:50 41 **********************
... ..( 6 skipped). .. **********************
17 2019-01-19 12:57 41 **********************
18 2019-01-19 12:58 32 *************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 3 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
Change History
(5)
| Component: |
all → drivedb
|
| Summary: |
New SATA drive model → not in db: HGST HUS726T6TALE6L4
|
| Version: |
→ 6.6
|
| Keywords: |
hdd added
|
| Milestone: |
→ unscheduled
|
| Milestone: |
unscheduled → Release 7.2
|
| Owner: |
set to Christian Franke
|
| Status: |
new → accepted
|
| Resolution: |
→ fixed
|
| Status: |
accepted → closed
|
Related (8TB): #1365.