smartctl 6.6 2017-11-05 r4594 [armv7l-linux-4.9.80-1-ARCH] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD10S21X-24R1BT0-SSHD-8GB Serial Number: WD-WX51A65KXNF2 LU WWN Device Id: 5 0014ee 65b386553 Firmware Version: 03.01A02 User Capacity: 1,000,204,886,016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Feb 15 21:49:35 2018 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 88 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (17820) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 198) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 190 187 021 - 1491 4 Start_Stop_Count -O--CK 097 097 000 - 3007 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 200 200 051 - 0 9 Power_On_Hours -O--CK 100 100 000 - 161 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 16 192 Power-Off_Retract_Count -O--CK 200 200 000 - 12 193 Load_Cycle_Count -O--CK 199 199 000 - 4969 194 Temperature_Celsius -O---K 105 095 000 - 42 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 240 Head_Flying_Hours -O--CK 100 100 000 - 28 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x14 GPL R/O 1 Hybrid Information log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: 24/51 Celsius Lifetime Min/Max Temperature: 24/52 Celsius Lifetime Average Temperature: 36 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (104) Index Estimated Time Temperature Celsius 105 2018-02-15 19:42 27 ******** ... ..( 2 skipped). .. ******** 108 2018-02-15 19:45 27 ******** 109 2018-02-15 19:46 26 ******* ... ..( 7 skipped). .. ******* 117 2018-02-15 19:54 26 ******* 118 2018-02-15 19:55 25 ****** ... ..( 8 skipped). .. ****** 127 2018-02-15 20:04 25 ****** 0 2018-02-15 20:05 24 ***** ... ..( 23 skipped). .. ***** 24 2018-02-15 20:29 24 ***** 25 2018-02-15 20:30 ? - 26 2018-02-15 20:31 24 ***** 27 2018-02-15 20:32 24 ***** 28 2018-02-15 20:33 ? - 29 2018-02-15 20:34 24 ***** ... ..( 9 skipped). .. ***** 39 2018-02-15 20:44 24 ***** 40 2018-02-15 20:45 25 ****** ... ..( 3 skipped). .. ****** 44 2018-02-15 20:49 25 ****** 45 2018-02-15 20:50 26 ******* ... ..( 7 skipped). .. ******* 53 2018-02-15 20:58 26 ******* 54 2018-02-15 20:59 27 ******** ... ..( 10 skipped). .. ******** 65 2018-02-15 21:10 27 ******** 66 2018-02-15 21:11 28 ********* 67 2018-02-15 21:12 28 ********* 68 2018-02-15 21:13 ? - 69 2018-02-15 21:14 28 ********* 70 2018-02-15 21:15 28 ********* 71 2018-02-15 21:16 30 *********** 72 2018-02-15 21:17 30 *********** 73 2018-02-15 21:18 ? - 74 2018-02-15 21:19 30 *********** 75 2018-02-15 21:20 30 *********** 76 2018-02-15 21:21 30 *********** 77 2018-02-15 21:22 31 ************ 78 2018-02-15 21:23 32 ************* 79 2018-02-15 21:24 32 ************* 80 2018-02-15 21:25 35 **************** 81 2018-02-15 21:26 35 **************** 82 2018-02-15 21:27 36 ***************** 83 2018-02-15 21:28 37 ****************** 84 2018-02-15 21:29 37 ****************** 85 2018-02-15 21:30 36 ***************** 86 2018-02-15 21:31 36 ***************** 87 2018-02-15 21:32 37 ****************** 88 2018-02-15 21:33 38 ******************* 89 2018-02-15 21:34 38 ******************* 90 2018-02-15 21:35 38 ******************* 91 2018-02-15 21:36 39 ******************** 92 2018-02-15 21:37 39 ******************** 93 2018-02-15 21:38 40 ********************* ... ..( 4 skipped). .. ********************* 98 2018-02-15 21:43 40 ********************* 99 2018-02-15 21:44 41 ********************** 100 2018-02-15 21:45 41 ********************** 101 2018-02-15 21:46 41 ********************** 102 2018-02-15 21:47 42 *********************** 103 2018-02-15 21:48 42 *********************** 104 2018-02-15 21:49 42 *********************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 371390 Vendor specific