smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.0-3-amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUSMM1640ASS200
Revision:             A360
Compliance:           SPC-4
User Capacity:        400,088,457,216 bytes [400 GB]
Logical block size:   512 bytes
Physical block size:  4096 bytes
LU is resource provisioned, LBPRZ=1
Rotation Rate:        Solid State Device
Form Factor:          2.5 inches
Logical Unit id:      0x5000cca04ec26e38
Serial number:        0QYEXUPA
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Fri Nov 24 15:34:04 2017 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Percentage used endurance indicator: 0%
Current Drive Temperature:     27 C
Drive Trip Temperature:        70 C

Manufactured in week 30 of year 2017
Specified cycle count over device lifetime:  0
Accumulated start-stop cycles:  0
Specified load-unload count over device lifetime:  0
Accumulated load-unload cycles:  0
defect list format 6 unknown
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 732546333671424

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0          0         43.168           0
write:         0        0         0         0          0       2002.007           0

Non-medium error count:        0

SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2104                 - [-   -    -]

Long (extended) Self Test duration: 2774 seconds [46.2 minutes]

Background scan results log
  Status: no scans active
    Accumulated power on time, hours:minutes 2104:45 [126285 minutes]
    Number of background scans performed: 0,  scan progress: 0.00%
    Number of background medium scans performed: 0

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca04ec26e39
    attached SAS address = 0x5003048009101a7f
    attached phy identifier = 0
    Invalid DWORD count = 4
    Running disparity error count = 4
    Loss of DWORD synchronization = 3
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 4
     Running disparity error count: 4
     Loss of dword synchronization count: 3
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca04ec26e3a
    attached SAS address = 0x5003048009101aff
    attached phy identifier = 0
    Invalid DWORD count = 4
    Running disparity error count = 4
    Loss of DWORD synchronization = 3
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 4
     Running disparity error count: 4
     Loss of dword synchronization count: 3
     Phy reset problem count: 0