smartctl 6.5 2016-05-07 r4318 [x86_64-w64-mingw32-win7-sp1] (sf-6.5-1) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD10JPLX-00MBPT0 Firmware Version: 01.01H01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Oct 03 03:43:18 2017 WEDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off supp ort. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 175) minutes. SCT capabilities: (0x0035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 100 100 040 - 0 3 Spin_Up_Time POS--- 122 122 033 - 2 4 Start_Stop_Count -O--C- 100 100 000 - 13 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 0 9 Power_On_Hours -O--C- 100 100 000 - 2 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 13 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 5 193 Load_Cycle_Count -O--C- 100 100 000 - 146 194 Temperature_Celsius -O---- 250 250 000 - 24 (Min/Max 22/41) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 22/24 Celsius Lifetime Min/Max Temperature: 22/41 Celsius Lifetime Average Temperature: 31 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (29) Index Estimated Time Temperature Celsius 30 2017-10-03 01:36 25 ****** 31 2017-10-03 01:37 25 ****** 32 2017-10-03 01:38 26 ******* 33 2017-10-03 01:39 27 ******** 34 2017-10-03 01:40 28 ********* 35 2017-10-03 01:41 29 ********** 36 2017-10-03 01:42 29 ********** 37 2017-10-03 01:43 31 ************ 38 2017-10-03 01:44 32 ************* 39 2017-10-03 01:45 32 ************* 40 2017-10-03 01:46 33 ************** 41 2017-10-03 01:47 34 *************** 42 2017-10-03 01:48 34 *************** 43 2017-10-03 01:49 34 *************** 44 2017-10-03 01:50 35 **************** 45 2017-10-03 01:51 36 ***************** 46 2017-10-03 01:52 36 ***************** 47 2017-10-03 01:53 37 ****************** 48 2017-10-03 01:54 37 ****************** 49 2017-10-03 01:55 38 ******************* 50 2017-10-03 01:56 38 ******************* 51 2017-10-03 01:57 38 ******************* 52 2017-10-03 01:58 39 ******************** ... ..( 2 skipped). .. ******************** 55 2017-10-03 02:01 39 ******************** 56 2017-10-03 02:02 40 ********************* ... ..( 4 skipped). .. ********************* 61 2017-10-03 02:07 40 ********************* 62 2017-10-03 02:08 41 ********************** ... ..( 7 skipped). .. ********************** 70 2017-10-03 02:16 41 ********************** 71 2017-10-03 02:17 40 ********************* 72 2017-10-03 02:18 40 ********************* 73 2017-10-03 02:19 ? - 74 2017-10-03 02:20 ? - 75 2017-10-03 02:21 ? - 76 2017-10-03 02:22 22 *** 77 2017-10-03 02:23 23 **** 78 2017-10-03 02:24 24 ***** 79 2017-10-03 02:25 25 ****** 80 2017-10-03 02:26 25 ****** 81 2017-10-03 02:27 26 ******* 82 2017-10-03 02:28 26 ******* 83 2017-10-03 02:29 27 ******** 84 2017-10-03 02:30 27 ******** 85 2017-10-03 02:31 28 ********* 86 2017-10-03 02:32 29 ********** 87 2017-10-03 02:33 30 *********** 88 2017-10-03 02:34 31 ************ 89 2017-10-03 02:35 31 ************ 90 2017-10-03 02:36 32 ************* 91 2017-10-03 02:37 33 ************** 92 2017-10-03 02:38 33 ************** 93 2017-10-03 02:39 34 *************** 94 2017-10-03 02:40 34 *************** 95 2017-10-03 02:41 35 **************** 96 2017-10-03 02:42 34 *************** ... ..( 15 skipped). .. *************** 112 2017-10-03 02:58 34 *************** 113 2017-10-03 02:59 33 ************** 114 2017-10-03 03:00 34 *************** 115 2017-10-03 03:01 34 *************** 116 2017-10-03 03:02 33 ************** ... ..( 13 skipped). .. ************** 2 2017-10-03 03:16 33 ************** 3 2017-10-03 03:17 34 *************** ... ..( 16 skipped). .. *************** 20 2017-10-03 03:34 34 *************** 21 2017-10-03 03:35 35 **************** 22 2017-10-03 03:36 35 **************** 23 2017-10-03 03:37 36 ***************** 24 2017-10-03 03:38 ? - 25 2017-10-03 03:39 ? - 26 2017-10-03 03:40 23 **** 27 2017-10-03 03:41 ? - 28 2017-10-03 03:42 23 **** 29 2017-10-03 03:43 23 **** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS