smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.10.0-28-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD4000FDYZ-27YA5B0 Serial Number: WD-WCC132156748 LU WWN Device Id: 5 0014ee 25f86430e Firmware Version: 01.01K06 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Jul 27 16:17:44 2017 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (47400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 513) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70b9) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 196 051 - 0 3 Spin_Up_Time POS--K 253 227 021 - 5541 4 Start_Stop_Count -O--CK 100 100 000 - 160 5 Reallocated_Sector_Ct PO--CK 198 198 140 - 85 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 068 068 000 - 23929 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 148 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 200 000 - 123 193 Load_Cycle_Count -O--CK 200 200 000 - 49 194 Temperature_Celsius -O---K 108 098 000 - 44 196 Reallocated_Event_Count -O--CK 190 190 000 - 10 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb1 GPL,SL VS 1 Device vendor specific log 0xb2 GPL VS 65535 Device vendor specific log 0xb2 SL VS 255 Device vendor specific log 0xb3-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 151 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 151 [6] occurred at disk power-on lifetime: 23084 hours (961 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 01 9e 04 0f 7a e0 00 Error: UNC 8 sectors at LBA = 0x19e040f7a = 6946033530 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 9e 04 0f 78 e0 0a 2d+09:42:59.972 READ DMA EXT 25 00 00 00 08 00 01 9e 04 0f 70 e0 0a 2d+09:42:59.972 READ DMA EXT 25 00 00 00 08 00 01 9e 04 0f 68 e0 0a 2d+09:42:59.972 READ DMA EXT 25 00 00 00 08 00 01 9e 04 0f 60 e0 0a 2d+09:42:59.972 READ DMA EXT 25 00 00 00 08 00 01 9e 04 0f 58 e0 0a 2d+09:42:59.972 READ DMA EXT Error 150 [5] occurred at disk power-on lifetime: 23084 hours (961 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 01 9e 04 0f 7a e0 00 Error: UNC 2048 sectors at LBA = 0x19e040f7a = 6946033530 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 01 9e 04 08 00 e0 0a 2d+09:42:56.533 READ DMA EXT 25 00 00 04 00 00 01 9e 04 04 00 e0 0a 2d+09:42:56.478 READ DMA EXT 25 00 00 04 00 00 01 9e 04 00 00 e0 0a 2d+09:42:56.472 READ DMA EXT 25 00 00 02 50 00 01 9e 03 fd b0 e0 0a 2d+09:42:56.469 READ DMA EXT 25 00 00 05 b0 00 01 9e 03 f8 00 e0 0a 2d+09:42:56.462 READ DMA EXT Error 149 [4] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 01 41 b5 ac 12 e0 00 Error: UNC 8 sectors at LBA = 0x141b5ac12 = 5397392402 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 41 b5 ac 10 e0 0a 2d+07:43:42.001 READ DMA EXT 25 00 00 00 08 00 01 41 b5 ac 08 e0 0a 2d+07:43:42.001 READ DMA EXT 25 00 00 00 08 00 01 41 b5 ac 00 e0 0a 2d+07:43:42.001 READ DMA EXT 25 00 00 00 08 00 01 41 b5 ab f8 e0 0a 2d+07:43:42.000 READ DMA EXT 25 00 00 00 08 00 01 41 b5 ab f0 e0 0a 2d+07:43:42.000 READ DMA EXT Error 148 [3] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 01 41 b5 a3 8a e0 00 Error: UNC 8 sectors at LBA = 0x141b5a38a = 5397390218 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 41 b5 a3 88 e0 0a 2d+07:43:40.148 READ DMA EXT 25 00 00 00 08 00 01 41 b5 a3 80 e0 0a 2d+07:43:40.148 READ DMA EXT 25 00 00 00 08 00 01 41 b5 a3 78 e0 0a 2d+07:43:40.148 READ DMA EXT 25 00 00 00 08 00 01 41 b5 a3 70 e0 0a 2d+07:43:40.148 READ DMA EXT 25 00 00 00 08 00 01 41 b5 a3 68 e0 0a 2d+07:43:40.148 READ DMA EXT Error 147 [2] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 01 41 b5 9b 02 e0 00 Error: UNC 8 sectors at LBA = 0x141b59b02 = 5397388034 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 41 b5 9b 00 e0 0a 2d+07:43:38.263 READ DMA EXT 25 00 00 00 08 00 01 41 b5 9a f8 e0 0a 2d+07:43:38.262 READ DMA EXT 25 00 00 00 08 00 01 41 b5 9a f0 e0 0a 2d+07:43:38.262 READ DMA EXT 25 00 00 00 08 00 01 41 b5 9a e8 e0 0a 2d+07:43:38.262 READ DMA EXT 25 00 00 00 08 00 01 41 b5 9a e0 e0 0a 2d+07:43:38.262 READ DMA EXT Error 146 [1] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 01 41 b5 92 79 e0 00 Error: UNC 8 sectors at LBA = 0x141b59279 = 5397385849 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 41 b5 92 78 e0 0a 2d+07:43:36.413 READ DMA EXT 25 00 00 00 08 00 01 41 b5 92 70 e0 0a 2d+07:43:36.413 READ DMA EXT 25 00 00 00 08 00 01 41 b5 92 68 e0 0a 2d+07:43:36.413 READ DMA EXT 25 00 00 00 08 00 01 41 b5 92 60 e0 0a 2d+07:43:36.413 READ DMA EXT 25 00 00 00 08 00 01 41 b5 92 58 e0 0a 2d+07:43:36.413 READ DMA EXT Error 145 [0] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 01 41 b5 89 f1 e0 00 Error: UNC 8 sectors at LBA = 0x141b589f1 = 5397383665 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 41 b5 89 f0 e0 0a 2d+07:43:34.558 READ DMA EXT 25 00 00 00 08 00 01 41 b5 89 e8 e0 0a 2d+07:43:34.558 READ DMA EXT 25 00 00 00 08 00 01 41 b5 89 e0 e0 0a 2d+07:43:34.558 READ DMA EXT 25 00 00 00 08 00 01 41 b5 89 d8 e0 0a 2d+07:43:34.558 READ DMA EXT 25 00 00 00 08 00 01 41 b5 89 d0 e0 0a 2d+07:43:34.558 READ DMA EXT Error 144 [23] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 01 41 b5 81 69 e0 00 Error: UNC 8 sectors at LBA = 0x141b58169 = 5397381481 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 41 b5 81 68 e0 0a 2d+07:43:32.677 READ DMA EXT 25 00 00 00 08 00 01 41 b5 81 60 e0 0a 2d+07:43:32.677 READ DMA EXT 25 00 00 00 08 00 01 41 b5 81 58 e0 0a 2d+07:43:32.677 READ DMA EXT 25 00 00 00 08 00 01 41 b5 81 50 e0 0a 2d+07:43:32.677 READ DMA EXT 25 00 00 00 08 00 01 41 b5 81 48 e0 0a 2d+07:43:32.677 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 23926 - # 2 Extended offline Completed without error 00% 23115 - # 3 Extended offline Aborted by host 90% 23105 - # 4 Short offline Completed without error 00% 23105 - # 5 Extended offline Aborted by host 90% 22935 - # 6 Short offline Completed without error 00% 22911 - # 7 Short captive Interrupted (host reset) 90% 22911 - # 8 Extended captive Interrupted (host reset) 90% 22901 - # 9 Extended offline Aborted by host 90% 22901 - #10 Short captive Completed without error 00% 22890 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 44 Celsius Power Cycle Min/Max Temperature: 40/45 Celsius Lifetime Min/Max Temperature: 19/54 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (78) Index Estimated Time Temperature Celsius 79 2017-07-27 08:20 44 ************************* ... ..( 48 skipped). .. ************************* 128 2017-07-27 09:09 44 ************************* 129 2017-07-27 09:10 41 ********************** ... ..(178 skipped). .. ********************** 308 2017-07-27 12:09 41 ********************** 309 2017-07-27 12:10 42 *********************** ... ..(150 skipped). .. *********************** 460 2017-07-27 14:41 42 *********************** 461 2017-07-27 14:42 43 ************************ ... ..( 67 skipped). .. ************************ 51 2017-07-27 15:50 43 ************************ 52 2017-07-27 15:51 44 ************************* ... ..( 25 skipped). .. ************************* 78 2017-07-27 16:17 44 ************************* SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1653355 Vendor specific