smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.10.0-514.26.2.el7.x86_64] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SAMSUNG MZ7LN512HMJP-00000 Firmware Version: MAV0100Q User Capacity: 512,110,190,592 bytes [512 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Sep 12 09:38:52 2017 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 265) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 099 099 010 - 1 9 Power_On_Hours -O--CK 099 099 000 - 3975 12 Power_Cycle_Count -O--CK 099 099 000 - 7 170 Unknown_Attribute -O--CK 099 099 010 - 1 171 Unknown_Attribute -O--CK 100 100 010 - 0 172 Unknown_Attribute -O--CK 100 100 010 - 0 173 Unknown_Attribute PO--CK 099 099 005 - 2 174 Unknown_Attribute -O--CK 100 100 000 - 0 178 Used_Rsvd_Blk_Cnt_Chip PO--C- 099 099 010 - 1 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 099 099 010 - 1603 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 099 099 000 - 6 194 Temperature_Celsius -O--CK 066 056 000 - 34 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 0 233 Media_Wearout_Indicator PO--C- 099 099 000 - 16749252 241 Total_LBAs_Written -O--CK 099 099 000 - 1452 242 Total_LBAs_Read -O--CK 099 099 000 - 13730 249 Unknown_Attribute -O--CK 099 099 000 - 1452 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xdf GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 6 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [1] occurred at disk power-on lifetime: 1735 hours (72 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 18 70 43 80 e0 00 Error: UNC 128 sectors at LBA = 0x18704380 = 410010496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 18 70 43 80 e0 18 21d+16:43:44.704 READ DMA EXT 47 00 00 00 01 00 00 00 00 08 30 e0 18 21d+16:43:44.704 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 13 e0 18 21d+16:43:44.704 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 e0 18 21d+16:43:44.704 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 18 21d+16:43:44.704 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 5 [0] occurred at disk power-on lifetime: 1735 hours (72 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 18 70 43 00 e0 00 Error: UNC 128 sectors at LBA = 0x18704300 = 410010368 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 18 70 43 00 e0 18 21d+16:43:44.704 READ DMA EXT 25 00 00 00 80 00 00 18 70 52 00 e0 18 21d+16:43:44.704 READ DMA EXT 25 00 00 00 80 00 00 18 70 51 80 e0 18 21d+16:43:44.704 READ DMA EXT 25 00 00 00 80 00 00 18 70 51 00 e0 18 21d+16:43:44.704 READ DMA EXT 25 00 00 00 80 00 00 18 70 50 80 e0 18 21d+16:43:44.704 READ DMA EXT Error 4 [3] occurred at disk power-on lifetime: 1735 hours (72 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 c0 00 00 18 70 4d 80 40 00 Error: UNC at LBA = 0x18704d80 = 410013056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 c0 00 00 18 70 4d 80 40 18 21d+16:43:43.704 READ FPDMA QUEUED 60 00 80 00 b8 00 00 18 70 4e 00 40 17 21d+16:43:43.704 READ FPDMA QUEUED 60 00 80 00 b0 00 00 18 70 4e 80 40 16 21d+16:43:43.704 READ FPDMA QUEUED 60 00 80 00 a8 00 00 18 70 4f 00 40 15 21d+16:43:43.704 READ FPDMA QUEUED 60 00 80 00 a0 00 00 18 70 4f 80 40 14 21d+16:43:43.704 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 1735 hours (72 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 48 00 00 18 70 52 00 40 00 Error: UNC at LBA = 0x18705200 = 410014208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 48 00 00 18 70 52 00 40 09 21d+16:43:43.704 READ FPDMA QUEUED 60 00 80 00 40 00 00 18 70 51 80 40 08 21d+16:43:43.704 READ FPDMA QUEUED 60 00 80 00 38 00 00 18 70 51 00 40 07 21d+16:43:43.704 READ FPDMA QUEUED 60 00 80 00 30 00 00 18 70 50 80 40 06 21d+16:43:43.704 READ FPDMA QUEUED 60 00 80 00 28 00 00 18 70 50 00 40 05 21d+16:43:43.704 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 21 - # 2 Extended offline Completed without error 00% 4 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 28/44 Celsius Lifetime Min/Max Temperature: 28/44 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (59) Index Estimated Time Temperature Celsius 60 2017-09-11 12:20 34 *************** ... ..(126 skipped). .. *************** 59 2017-09-12 09:30 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 33 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 33 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC