smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.2.7-200.fc22.x86_64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD80EFAX-68LHPN0 Firmware Version: 83.H0A83 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jul 12 22:03:49 2017 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 164 (intermediate level without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 93) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 941) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance --S--- 100 100 054 - 0 3 Spin_Up_Time POS--- 100 100 024 - 0 4 Start_Stop_Count -O--C- 100 100 000 - 4 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate -O-R-- 100 100 067 - 0 8 Seek_Time_Performance --S--- 100 100 020 - 0 9 Power_On_Hours -O--C- 100 100 000 - 0 10 Spin_Retry_Count -O--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 4 22 Unknown_Attribute PO---K 100 100 025 - 100 192 Power-Off_Retract_Count -O--CK 100 100 000 - 4 193 Load_Cycle_Count -O--C- 100 100 000 - 4 194 Temperature_Celsius -O---- 154 154 000 - 42 (Min/Max 25/42) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 5501 Pending Defects log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ NON-DATA log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL,SL R/W 1 SATA Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 0 Device State: Active (0) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: 25/42 Celsius Lifetime Min/Max Temperature: 25/42 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/65 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (46) Index Estimated Time Temperature Celsius 47 2017-07-12 19:56 0 - ... ..( 79 skipped). .. - 127 2017-07-12 21:16 0 - 0 2017-07-12 21:17 28 ********* 1 2017-07-12 21:18 25 ****** 2 2017-07-12 21:19 26 ******* 3 2017-07-12 21:20 26 ******* 4 2017-07-12 21:21 27 ******** 5 2017-07-12 21:22 28 ********* 6 2017-07-12 21:23 28 ********* 7 2017-07-12 21:24 29 ********** 8 2017-07-12 21:25 29 ********** 9 2017-07-12 21:26 30 *********** 10 2017-07-12 21:27 31 ************ 11 2017-07-12 21:28 31 ************ 12 2017-07-12 21:29 32 ************* 13 2017-07-12 21:30 32 ************* 14 2017-07-12 21:31 32 ************* 15 2017-07-12 21:32 33 ************** 16 2017-07-12 21:33 33 ************** 17 2017-07-12 21:34 34 *************** 18 2017-07-12 21:35 34 *************** 19 2017-07-12 21:36 34 *************** 20 2017-07-12 21:37 35 **************** 21 2017-07-12 21:38 35 **************** 22 2017-07-12 21:39 36 ***************** 23 2017-07-12 21:40 36 ***************** 24 2017-07-12 21:41 36 ***************** 25 2017-07-12 21:42 37 ****************** 26 2017-07-12 21:43 37 ****************** 27 2017-07-12 21:44 37 ****************** 28 2017-07-12 21:45 38 ******************* ... ..( 2 skipped). .. ******************* 31 2017-07-12 21:48 38 ******************* 32 2017-07-12 21:49 39 ******************** 33 2017-07-12 21:50 39 ******************** 34 2017-07-12 21:51 39 ******************** 35 2017-07-12 21:52 40 ********************* ... ..( 3 skipped). .. ********************* 39 2017-07-12 21:56 40 ********************* 40 2017-07-12 21:57 41 ********************** ... ..( 2 skipped). .. ********************** 43 2017-07-12 22:00 41 ********************** 44 2017-07-12 22:01 42 *********************** 45 2017-07-12 22:02 42 *********************** 46 2017-07-12 22:03 0 - SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS