smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-21-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SAMSUNG HD082GJ Serial Number: S0VPJ9AQ402566 LU WWN Device Id: 5 0000f0 09b402566 Firmware Version: GE100-07 User Capacity: 80,026,361,856 bytes [80.0 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Apr 13 18:31:02 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1320) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 22) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 18 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 073 073 011 - 4000 4 Start_Stop_Count -O--CK 089 089 000 - 10249 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate POSR-- 252 252 051 - 0 8 Seek_Time_Performance P-S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 099 099 000 - 462713 10 Spin_Retry_Count PO--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--C- 252 252 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 4795 184 End-to-End_Error -O--CK 252 252 000 - 0 187 Reported_Uncorrect -O--CK 252 252 000 - 0 188 Command_Timeout -O--CK 252 252 000 - 0 190 Airflow_Temperature_Cel -O---K 160 106 000 - 31 194 Temperature_Celsius -O---K 160 106 000 - 31 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--C- 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 1 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 252 252 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 25 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 25 [0] occurred at disk power-on lifetime: 3854 hours (160 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 00 c2 4f 09 40 00 Error: ICRC, ABRT at LBA = 0x00c24f09 = 12734217 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 80 00 80 00 00 00 c2 4f 09 40 ff 00:41:06.000 WRITE FPDMA QUEUED 61 00 80 00 80 00 00 00 c2 4f 09 40 00 00:41:06.000 WRITE FPDMA QUEUED 61 00 80 00 80 00 00 00 c2 4f 09 40 00 00:41:06.000 WRITE FPDMA QUEUED 61 00 80 00 80 00 00 00 c2 4f 09 40 00 00:41:06.000 WRITE FPDMA QUEUED 61 00 80 00 80 00 00 00 c2 4f 09 40 00 00:41:06.000 WRITE FPDMA QUEUED Error 24 [7] occurred at disk power-on lifetime: 3852 hours (160 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 c2 4f 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 da 00 00 00 00 00 c2 4f 00 e0 04 00:01:59.000 SMART RETURN STATUS c6 00 00 00 10 00 00 00 00 00 00 a0 04 00:00:26.000 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 04 00:00:26.000 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 04 00:00:26.000 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:26.000 IDENTIFY DEVICE Error 23 [6] occurred at disk power-on lifetime: 3851 hours (160 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 c2 4f 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d0 00 00 00 00 00 c2 4f 00 e0 00 00:00:26.000 SMART READ DATA ca 00 00 00 08 00 00 00 5e 6d 60 e0 00 00:00:26.000 WRITE DMA Error 22 [5] occurred at disk power-on lifetime: 3851 hours (160 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 c2 4f 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 da 00 00 00 00 00 c2 4f 00 e0 04 00:00:26.000 SMART RETURN STATUS c6 00 00 00 10 00 00 00 00 00 00 a0 04 00:00:25.000 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 04 00:00:25.000 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 04 00:00:25.000 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:25.000 IDENTIFY DEVICE Error 21 [4] occurred at disk power-on lifetime: 3854 hours (160 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 00 c2 4f 09 40 00 Error: ICRC, ABRT at LBA = 0x00c24f09 = 12734217 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 80 00 80 00 00 00 c2 4f 09 40 ff 00:41:06.000 WRITE FPDMA QUEUED 61 00 80 00 80 00 00 00 c2 4f 09 40 00 00:41:06.000 WRITE FPDMA QUEUED 61 00 80 00 80 00 00 00 c2 4f 09 40 00 00:41:06.000 WRITE FPDMA QUEUED 61 00 80 00 80 00 00 00 c2 4f 09 40 00 00:41:06.000 WRITE FPDMA QUEUED 61 00 80 00 80 00 00 00 c2 4f 09 40 00 00:41:06.000 WRITE FPDMA QUEUED Error 20 [3] occurred at disk power-on lifetime: 3852 hours (160 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 c2 4f 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 da 00 00 00 00 00 c2 4f 00 e0 04 00:01:59.000 SMART RETURN STATUS c6 00 00 00 10 00 00 00 00 00 00 a0 04 00:00:26.000 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 04 00:00:26.000 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 04 00:00:26.000 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:26.000 IDENTIFY DEVICE Error 19 [2] occurred at disk power-on lifetime: 3851 hours (160 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 c2 4f 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d0 00 00 00 00 00 c2 4f 00 e0 00 00:00:26.000 SMART READ DATA ca 00 00 00 08 00 00 00 5e 6d 60 e0 00 00:00:26.000 WRITE DMA Error 18 [1] occurred at disk power-on lifetime: 3851 hours (160 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 c2 4f 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 da 00 00 00 00 00 c2 4f 00 e0 04 00:00:26.000 SMART RETURN STATUS c6 00 00 00 10 00 00 00 00 00 00 a0 04 00:00:25.000 SET MULTIPLE MODE ef 00 03 00 45 00 00 00 00 00 00 a0 04 00:00:25.000 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 a0 04 00:00:25.000 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:25.000 IDENTIFY DEVICE Warning! SMART Extended Self-test Log Structure error: invalid SMART checksum. SMART Extended Self-test Log Version: 0 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Reserved (0x0e) Completed without error 150% 0 - # 2 Offline Completed without error 00% 0 - # 3 Offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: --/40 Celsius Lifetime Min/Max Temperature: --/40 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 10/105 Celsius Min/Max Temperature Limit: 5/110 Celsius Temperature History Size (Index): 128 (11) Index Estimated Time Temperature Celsius 12 2023-04-13 16:24 47 **************************** ... ..( 43 skipped). .. **************************** 56 2023-04-13 17:08 47 **************************** 57 2023-04-13 17:09 48 ***************************** 58 2023-04-13 17:10 48 ***************************** 59 2023-04-13 17:11 48 ***************************** 60 2023-04-13 17:12 ? - 61 2023-04-13 17:13 24 ***** 62 2023-04-13 17:14 ? - 63 2023-04-13 17:15 ? - 64 2023-04-13 17:16 21 ** 65 2023-04-13 17:17 ? - 66 2023-04-13 17:18 22 *** 67 2023-04-13 17:19 40 ********************* ... ..( 10 skipped). .. ********************* 78 2023-04-13 17:30 40 ********************* 79 2023-04-13 17:31 ? - 80 2023-04-13 17:32 36 ***************** 81 2023-04-13 17:33 36 ***************** 82 2023-04-13 17:34 35 **************** 83 2023-04-13 17:35 35 **************** 84 2023-04-13 17:36 35 **************** 85 2023-04-13 17:37 34 *************** ... ..( 3 skipped). .. *************** 89 2023-04-13 17:41 34 *************** 90 2023-04-13 17:42 33 ************** 91 2023-04-13 17:43 32 ************* ... ..( 4 skipped). .. ************* 96 2023-04-13 17:48 32 ************* 97 2023-04-13 17:49 31 ************ 98 2023-04-13 17:50 31 ************ 99 2023-04-13 17:51 32 ************* ... ..( 5 skipped). .. ************* 105 2023-04-13 17:57 32 ************* 106 2023-04-13 17:58 31 ************ ... ..( 10 skipped). .. ************ 117 2023-04-13 18:09 31 ************ 118 2023-04-13 18:10 30 *********** ... ..( 15 skipped). .. *********** 6 2023-04-13 18:26 30 *********** 7 2023-04-13 18:27 31 ************ ... ..( 3 skipped). .. ************ 11 2023-04-13 18:31 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 1 Command failed due to ICRC error 0x0002 2 1 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 1 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 1 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 1 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC