smartctl 7.3 2022-02-28 r5338 [x86_64-w64-mingw32-w10-21H2] (sf-7.3-1) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z7K500 Device Model: HGST HTS725050A7E630 Serial Number: RC250FCB1DGU7K LU WWN Device Id: 5 000cca 7a5d3c391 Firmware Version: GS2OA340 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5364 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed May 18 06:29:12 2022 NZST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 5314) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 90) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 088 064 062 - 2621481 2 Throughput_Performance P-S--K 198 100 040 - 100 3 Spin_Up_Time PO---K 248 100 033 - 1 4 Start_Stop_Count -O--CK 100 100 000 - 269 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 64 (0 7) 7 Seek_Error_Rate POSR-K 099 099 067 - 1 8 Seek_Time_Performance P-S--K 152 100 040 - 33 9 Power_On_Hours -O--CK 028 028 000 - 31927 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 265 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 112137301134501 188 Command_Timeout -O--CK 100 100 000 - 4295032832 190 Airflow_Temperature_Cel -O---K 076 058 045 - 24 (Min/Max 19/24) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 27 192 Power-Off_Retract_Count -O--CK 100 100 000 - 4587590 193 Load_Cycle_Count -O--CK 020 020 000 - 809389 196 Reallocated_Event_Count -O--CK 100 100 000 - 8 197 Current_Pending_Sector -O--CK 039 039 000 - 1600 198 Offline_Uncorrectable ----CK 100 057 000 - 26 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0 223 Load_Retry_Count -O-R-K 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 3237 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3237 [0] occurred at disk power-on lifetime: 31927 hours (1330 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 10 a2 a0 00 00 Error: UNC 8 sectors at LBA = 0x0010a2a0 = 1090208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 10 a2 a0 40 00 00:04:51.850 READ DMA EXT 25 00 00 00 08 00 00 03 47 4d 28 40 00 00:04:51.850 READ DMA EXT 25 00 00 00 08 00 00 03 47 4d 10 40 00 00:04:51.846 READ DMA EXT 25 00 00 00 08 00 00 00 70 bc 60 40 00 00:04:51.832 READ DMA EXT 25 00 00 00 01 00 00 03 14 26 c8 40 00 00:04:51.823 READ DMA EXT Error 3236 [3] occurred at disk power-on lifetime: 31927 hours (1330 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 10 a2 a0 00 00 Error: UNC 8 sectors at LBA = 0x0010a2a0 = 1090208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 10 a2 a0 40 00 00:04:48.675 READ DMA EXT 25 00 00 00 08 00 00 03 47 4d 28 40 00 00:04:48.675 READ DMA EXT 25 00 00 00 08 00 00 03 47 4d 10 40 00 00:04:48.670 READ DMA EXT 25 00 00 00 08 00 00 00 70 bc 60 40 00 00:04:48.657 READ DMA EXT 25 00 00 00 01 00 00 03 14 26 c8 40 00 00:04:48.648 READ DMA EXT Error 3235 [2] occurred at disk power-on lifetime: 31927 hours (1330 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 10 a2 a0 00 00 Error: UNC 8 sectors at LBA = 0x0010a2a0 = 1090208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 10 a2 a0 40 00 00:04:45.475 READ DMA EXT 25 00 00 00 08 00 00 03 47 4d 28 40 00 00:04:45.475 READ DMA EXT 25 00 00 00 08 00 00 03 47 4d 10 40 00 00:04:45.470 READ DMA EXT 25 00 00 00 08 00 00 00 70 bc 60 40 00 00:04:45.456 READ DMA EXT 25 00 00 00 01 00 00 03 14 26 c8 40 00 00:04:45.447 READ DMA EXT Error 3234 [1] occurred at disk power-on lifetime: 31927 hours (1330 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 10 a2 a0 00 00 Error: UNC 8 sectors at LBA = 0x0010a2a0 = 1090208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 10 a2 a0 40 00 00:04:42.291 READ DMA EXT 25 00 00 00 08 00 00 03 47 4d 28 40 00 00:04:42.291 READ DMA EXT 25 00 00 00 08 00 00 03 47 4d 10 40 00 00:04:42.286 READ DMA EXT 25 00 00 00 08 00 00 00 70 bc 60 40 00 00:04:42.273 READ DMA EXT 25 00 00 00 01 00 00 03 14 26 c8 40 00 00:04:42.264 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 90% 31927 1090208 # 2 Short offline Completed without error 00% 116 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 19/24 Celsius Lifetime Min/Max Temperature: 5/42 Celsius Specified Max Operating Temperature: 25 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (67) Index Estimated Time Temperature Celsius 68 2022-05-18 04:22 23 **** ... ..( 4 skipped). .. **** 73 2022-05-18 04:27 23 **** 74 2022-05-18 04:28 24 ***** 75 2022-05-18 04:29 24 ***** 76 2022-05-18 04:30 23 **** 77 2022-05-18 04:31 24 ***** ... ..( 11 skipped). .. ***** 89 2022-05-18 04:43 24 ***** 90 2022-05-18 04:44 23 **** 91 2022-05-18 04:45 24 ***** ... ..( 6 skipped). .. ***** 98 2022-05-18 04:52 24 ***** 99 2022-05-18 04:53 23 **** 100 2022-05-18 04:54 23 **** 101 2022-05-18 04:55 23 **** 102 2022-05-18 04:56 24 ***** ... ..( 2 skipped). .. ***** 105 2022-05-18 04:59 24 ***** 106 2022-05-18 05:00 23 **** 107 2022-05-18 05:01 24 ***** 108 2022-05-18 05:02 24 ***** 109 2022-05-18 05:03 24 ***** 110 2022-05-18 05:04 23 **** 111 2022-05-18 05:05 23 **** 112 2022-05-18 05:06 24 ***** 113 2022-05-18 05:07 23 **** ... ..( 2 skipped). .. **** 116 2022-05-18 05:10 23 **** 117 2022-05-18 05:11 24 ***** 118 2022-05-18 05:12 24 ***** 119 2022-05-18 05:13 24 ***** 120 2022-05-18 05:14 23 **** 121 2022-05-18 05:15 24 ***** 122 2022-05-18 05:16 24 ***** 123 2022-05-18 05:17 23 **** ... ..( 52 skipped). .. **** 48 2022-05-18 06:10 23 **** 49 2022-05-18 06:11 ? - 50 2022-05-18 06:12 22 *** 51 2022-05-18 06:13 24 ***** 52 2022-05-18 06:14 24 ***** 53 2022-05-18 06:15 25 ****** 54 2022-05-18 06:16 25 ****** 55 2022-05-18 06:17 26 ******* 56 2022-05-18 06:18 ? - 57 2022-05-18 06:19 ? - 58 2022-05-18 06:20 ? - 59 2022-05-18 06:21 22 *** 60 2022-05-18 06:22 23 **** 61 2022-05-18 06:23 24 ***** 62 2022-05-18 06:24 25 ****** 63 2022-05-18 06:25 ? - 64 2022-05-18 06:26 20 * 65 2022-05-18 06:27 22 *** 66 2022-05-18 06:28 22 *** 67 2022-05-18 06:29 23 **** SMART WRITE LOG does not return COUNT and LBA_LOW register SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS