smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-25-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD161KFGX-68AFPN0 Serial Number: 3WJ5YP6P LU WWN Device Id: 5 000cca 284dee44b Firmware Version: 83.00A83 User Capacity: 16,000,900,661,248 bytes [16.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 published, ANSI INCITS 529-2018 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed May 11 17:38:00 2022 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 101) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (1888) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 001 - 0 2 Throughput_Performance --S--- 100 100 054 - 0 3 Spin_Up_Time POS--- 095 095 001 - 208 4 Start_Stop_Count -O--C- 100 100 000 - 3 5 Reallocated_Sector_Ct PO--CK 100 100 001 - 0 7 Seek_Error_Rate -O-R-- 100 100 001 - 0 8 Seek_Time_Performance --S--- 100 100 020 - 0 9 Power_On_Hours -O--C- 100 100 000 - 0 10 Spin_Retry_Count -O--C- 100 100 001 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 3 22 Unknown_Attribute PO---K 100 100 025 - 100 192 Power-Off_Retract_Count -O--CK 100 100 000 - 3 193 Load_Cycle_Count -O--C- 100 100 000 - 3 194 Temperature_Celsius -O---- 060 060 000 - 34 (Min/Max 20/34) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 30001 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL R/W 1 Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x2f GPL - 1 Set Sector Configuration 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 25/34 Celsius Lifetime Min/Max Temperature: 20/34 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Minimum supported ERC Time Limit: 70 (7.0 seconds) SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (63) Index Estimated Time Temperature Celsius 64 2022-05-11 15:31 0 - ... ..( 62 skipped). .. - 127 2022-05-11 16:34 0 - 0 2022-05-11 16:35 22 *** 1 2022-05-11 16:36 22 *** 2 2022-05-11 16:37 22 *** 3 2022-05-11 16:38 23 **** 4 2022-05-11 16:39 23 **** 5 2022-05-11 16:40 23 **** 6 2022-05-11 16:41 25 ****** 7 2022-05-11 16:42 25 ****** 8 2022-05-11 16:43 26 ******* ... ..( 2 skipped). .. ******* 11 2022-05-11 16:46 26 ******* 12 2022-05-11 16:47 27 ******** ... ..( 3 skipped). .. ******** 16 2022-05-11 16:51 27 ******** 17 2022-05-11 16:52 28 ********* 18 2022-05-11 16:53 28 ********* 19 2022-05-11 16:54 28 ********* 20 2022-05-11 16:55 29 ********** ... ..( 9 skipped). .. ********** 30 2022-05-11 17:05 29 ********** 31 2022-05-11 17:06 30 *********** ... ..( 4 skipped). .. *********** 36 2022-05-11 17:11 30 *********** 37 2022-05-11 17:12 31 ************ ... ..( 3 skipped). .. ************ 41 2022-05-11 17:16 31 ************ 42 2022-05-11 17:17 32 ************* ... ..( 8 skipped). .. ************* 51 2022-05-11 17:26 32 ************* 52 2022-05-11 17:27 33 ************** ... ..( 6 skipped). .. ************** 59 2022-05-11 17:34 33 ************** 60 2022-05-11 17:35 34 *************** 61 2022-05-11 17:36 34 *************** 62 2022-05-11 17:37 34 *************** 63 2022-05-11 17:38 0 - SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 3 --- Lifetime Power-On Resets 0x01 0x010 4 0 --- Power-on Hours 0x01 0x018 6 0 --- Logical Sectors Written 0x01 0x020 6 0 --- Number of Write Commands 0x01 0x028 6 84067 --- Logical Sectors Read 0x01 0x030 6 1856 --- Number of Read Commands 0x01 0x038 6 3549000 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 0 --- Spindle Motor Power-on Hours 0x03 0x010 4 0 --- Head Flying Hours 0x03 0x018 4 3 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 34 --- Current Temperature 0x05 0x010 1 - N-- Average Short Term Temperature 0x05 0x018 1 - N-- Average Long Term Temperature 0x05 0x020 1 34 --- Highest Temperature 0x05 0x028 1 20 --- Lowest Temperature 0x05 0x030 1 - N-- Highest Average Short Term Temperature 0x05 0x038 1 - N-- Lowest Average Short Term Temperature 0x05 0x040 1 - N-- Highest Average Long Term Temperature 0x05 0x048 1 - N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 16 --- Number of Hardware Resets 0x06 0x010 4 5 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == 0xff 0x040 7 0 --- Vendor Specific 0xff 0x048 7 0 --- Vendor Specific 0xff 0x050 7 0 --- Vendor Specific 0xff 0x058 7 0 --- Vendor Specific 0xff 0x060 7 0 --- Vendor Specific 0xff 0x068 7 0 --- Vendor Specific 0xff 0x070 7 0 --- Vendor Specific 0xff 0x078 7 0 --- Vendor Specific 0xff 0x080 7 0 --- Vendor Specific |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS