smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.17.1-arch1-1] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD140EDGZ-11B2DA2 Firmware Version: 85.00A85 User Capacity: 14,000,519,643,136 bytes [14.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5319 ATA Version is: ACS-4 published, ANSI INCITS 529-2018 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Apr 7 22:33:49 2022 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 101) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (1528) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 001 - 0 2 Throughput_Performance --S--- 100 100 054 - 0 3 Spin_Up_Time POS--- 085 085 001 - 280 (Average 327) 4 Start_Stop_Count -O--C- 100 100 000 - 7 5 Reallocated_Sector_Ct PO--CK 100 100 001 - 0 7 Seek_Error_Rate -O-R-- 100 100 001 - 0 8 Seek_Time_Performance --S--- 100 100 020 - 0 9 Power_On_Hours -O--C- 100 100 000 - 0 10 Spin_Retry_Count -O--C- 100 100 001 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 5 22 Unknown_Attribute PO---K 100 100 025 - 100 192 Power-Off_Retract_Count -O--CK 100 100 000 - 7 193 Load_Cycle_Count -O--C- 100 100 000 - 7 194 Temperature_Celsius -O---- 045 045 000 - 36 (Min/Max 23/38) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 30001 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL R/W 1 Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x2f GPL - 1 Set Sector Configuration 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb7 SL VS 1 Device vendor specific log 0xd8 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 23/38 Celsius Lifetime Min/Max Temperature: 23/38 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Minimum supported ERC Time Limit: 65 (6.5 seconds) SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/65 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (49) Index Estimated Time Temperature Celsius 50 2022-04-07 20:26 0 - ... ..( 76 skipped). .. - 127 2022-04-07 21:43 0 - 0 2022-04-07 21:44 24 ***** 1 2022-04-07 21:45 23 **** 2 2022-04-07 21:46 24 ***** 3 2022-04-07 21:47 23 **** 4 2022-04-07 21:48 24 ***** 5 2022-04-07 21:49 25 ****** 6 2022-04-07 21:50 25 ****** 7 2022-04-07 21:51 26 ******* 8 2022-04-07 21:52 27 ******** 9 2022-04-07 21:53 28 ********* 10 2022-04-07 21:54 28 ********* 11 2022-04-07 21:55 29 ********** 12 2022-04-07 21:56 29 ********** 13 2022-04-07 21:57 30 *********** 14 2022-04-07 21:58 30 *********** 15 2022-04-07 21:59 31 ************ 16 2022-04-07 22:00 31 ************ 17 2022-04-07 22:01 32 ************* ... ..( 3 skipped). .. ************* 21 2022-04-07 22:05 32 ************* 22 2022-04-07 22:06 33 ************** 23 2022-04-07 22:07 33 ************** 24 2022-04-07 22:08 33 ************** 25 2022-04-07 22:09 34 *************** 26 2022-04-07 22:10 34 *************** 27 2022-04-07 22:11 34 *************** 28 2022-04-07 22:12 35 **************** 29 2022-04-07 22:13 35 **************** 30 2022-04-07 22:14 36 ***************** ... ..( 2 skipped). .. ***************** 33 2022-04-07 22:17 36 ***************** 34 2022-04-07 22:18 37 ****************** 35 2022-04-07 22:19 37 ****************** 36 2022-04-07 22:20 37 ****************** 37 2022-04-07 22:21 38 ******************* ... ..( 2 skipped). .. ******************* 40 2022-04-07 22:24 38 ******************* 41 2022-04-07 22:25 37 ****************** ... ..( 3 skipped). .. ****************** 45 2022-04-07 22:29 37 ****************** 46 2022-04-07 22:30 36 ***************** 47 2022-04-07 22:31 36 ***************** 48 2022-04-07 22:32 36 ***************** 49 2022-04-07 22:33 0 - SMART WRITE LOG does not return COUNT and LBA_LOW register SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 5 --- Lifetime Power-On Resets 0x01 0x010 4 0 --- Power-on Hours 0x01 0x018 6 1015167 --- Logical Sectors Written 0x01 0x020 6 1390 --- Number of Write Commands 0x01 0x028 6 844167 --- Logical Sectors Read 0x01 0x030 6 1478 --- Number of Read Commands 0x01 0x038 6 2887950 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 0 --- Spindle Motor Power-on Hours 0x03 0x010 4 0 --- Head Flying Hours 0x03 0x018 4 7 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 36 --- Current Temperature 0x05 0x010 1 - N-- Average Short Term Temperature 0x05 0x018 1 - N-- Average Long Term Temperature 0x05 0x020 1 38 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x030 1 - N-- Highest Average Short Term Temperature 0x05 0x038 1 - N-- Lowest Average Short Term Temperature 0x05 0x040 1 - N-- Highest Average Long Term Temperature 0x05 0x048 1 - N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 65 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 4 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS