smartctl 7.2 2020-12-30 r5155 [x86_64-w64-mingw32-w10-b19043] (sf-7.2-1) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device Model: ST3500320AS Serial Number: 9QM7K500 LU WWN Device Id: 5 000c50 0105b787d Firmware Version: SD1A User Capacity: 500 106 780 160 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Feb 12 14:09:10 2022 SE SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 634) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 118) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 116 091 006 - 908154 3 Spin_Up_Time PO---- 095 094 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3238 5 Reallocated_Sector_Ct PO--CK 094 094 036 - 133 7 Seek_Error_Rate POSR-- 087 060 030 - 642590049 9 Power_On_Hours -O--CK 079 079 000 - 18610 10 Spin_Retry_Count PO--C- 100 100 097 - 4 12 Power_Cycle_Count -O--CK 098 098 020 - 3041 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 248 188 Command_Timeout -O--CK 100 098 000 - 25770197043 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 059 055 045 - 41 (Min/Max 39/41) 194 Temperature_Celsius -O---K 041 045 000 - 41 (0 8 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 041 033 000 - 908154 197 Current_Pending_Sector -O--C- 100 100 000 - 27 198 Offline_Uncorrectable ----C- 100 100 000 - 27 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 53 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2819 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 248 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 248 [7] occurred at disk power-on lifetime: 18290 hours (762 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3c 00 8c 2e 00 00 Error: WP at LBA = 0x3c008c2e = 1006668846 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 10 cc 00 c2 f0 40 00 00:37:12.405 WRITE FPDMA QUEUED 61 00 00 00 40 00 0d 9c 00 cf 30 40 00 00:37:12.403 WRITE FPDMA QUEUED 61 00 00 00 08 00 20 2e 00 f4 40 40 00 00:37:12.403 WRITE FPDMA QUEUED 60 00 00 00 08 00 00 3c 00 8c 28 40 00 00:37:12.402 READ FPDMA QUEUED 61 00 00 00 10 00 10 cc 00 c2 68 40 00 00:37:12.401 WRITE FPDMA QUEUED Error 247 [6] occurred at disk power-on lifetime: 18290 hours (762 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3c 00 8c 2e 00 00 Error: UNC at LBA = 0x3c008c2e = 1006668846 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 90 00 10 79 00 2c 62 40 00 00:37:08.552 READ FPDMA QUEUED 60 00 00 00 18 00 10 76 00 2c b2 40 00 00:37:08.552 READ FPDMA QUEUED 60 00 00 01 00 00 10 75 00 2c b2 40 00 00:37:08.552 READ FPDMA QUEUED 60 00 00 01 00 00 10 74 00 2c b2 40 00 00:37:08.551 READ FPDMA QUEUED 60 00 00 01 00 00 10 73 00 2c b2 40 00 00:37:08.551 READ FPDMA QUEUED Error 246 [5] occurred at disk power-on lifetime: 18290 hours (762 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3c 00 8c 61 00 00 Error: UNC at LBA = 0x3c008c61 = 1006668897 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 00 3c 00 8c 88 40 00 00:36:48.591 READ FPDMA QUEUED 61 00 00 00 10 00 10 f1 00 14 88 40 00 00:36:47.476 WRITE FPDMA QUEUED 60 00 00 00 80 00 00 3c 00 8c 08 40 00 00:36:47.476 READ FPDMA QUEUED 60 00 00 00 80 00 00 3b 00 8c 88 40 00 00:36:47.475 READ FPDMA QUEUED 61 00 00 00 10 00 10 f1 00 14 98 40 00 00:36:47.457 WRITE FPDMA QUEUED Error 245 [4] occurred at disk power-on lifetime: 18283 hours (761 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 69 00 81 c3 00 00 Error: UNC at LBA = 0x690081c3 = 1761640899 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 5d 00 81 00 40 00 01:37:11.409 READ FPDMA QUEUED 60 00 00 01 00 00 00 56 00 81 00 40 00 01:37:11.026 READ FPDMA QUEUED 60 00 00 01 00 00 00 4f 00 81 00 40 00 01:37:10.713 READ FPDMA QUEUED 60 00 00 01 00 00 00 4e 00 81 00 40 00 01:37:10.713 READ FPDMA QUEUED 60 00 00 01 00 00 00 4d 00 81 00 40 00 01:37:10.713 READ FPDMA QUEUED Error 244 [3] occurred at disk power-on lifetime: 18282 hours (761 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e8 00 1d ae 00 00 Error: UNC at LBA = 0xe8001dae = 3892321710 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 df 00 15 00 40 00 00:34:52.481 READ FPDMA QUEUED 60 00 00 01 00 00 00 de 00 15 00 40 00 00:34:52.481 READ FPDMA QUEUED 60 00 00 01 00 00 00 dd 00 15 00 40 00 00:34:52.481 READ FPDMA QUEUED 60 00 00 01 00 00 00 dc 00 15 00 40 00 00:34:52.480 READ FPDMA QUEUED 60 00 00 01 00 00 00 db 00 15 00 40 00 00:34:52.480 READ FPDMA QUEUED Error 243 [2] occurred at disk power-on lifetime: 18281 hours (761 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 4e 00 81 b2 00 00 Error: WP at LBA = 0x4e0081b2 = 1308656050 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 10 cc 00 c2 d0 40 00 00:01:32.817 WRITE FPDMA QUEUED 61 00 00 00 e8 00 0c 99 00 22 e0 40 00 00:01:32.815 WRITE FPDMA QUEUED 61 00 00 00 28 00 10 cd 00 c2 30 40 00 00:01:32.814 WRITE FPDMA QUEUED 60 00 00 00 20 00 12 b9 00 e6 8e 40 00 00:01:32.789 READ FPDMA QUEUED 60 00 00 00 40 00 10 3d 00 26 22 40 00 00:01:32.783 READ FPDMA QUEUED Error 242 [1] occurred at disk power-on lifetime: 18274 hours (761 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6a 00 1d 29 00 00 Error: UNC at LBA = 0x6a001d29 = 1778392361 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 01 00 00 00 6a 00 1d 00 40 00 05:01:39.256 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 d8 00 15 00 e0 00 05:01:36.629 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 f6 00 0f 00 e0 00 05:00:25.271 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 09 00 00 00 e0 00 05:00:20.326 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 08 00 00 00 e0 00 05:00:20.313 READ VERIFY SECTOR(S) EXT Error 241 [0] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6a 00 1d 29 00 00 Error: UNC at LBA = 0x6a001d29 = 1778392361 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 6a 00 1d 28 40 00 02:11:59.521 READ FPDMA QUEUED 60 00 00 00 08 00 00 6a 00 1d 20 40 00 02:11:59.478 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 02:11:59.411 READ LOG EXT 60 00 00 00 08 00 00 6a 00 1d 08 40 00 02:11:56.498 READ FPDMA QUEUED 60 00 00 00 08 00 00 6a 00 1d 00 40 00 02:11:56.373 READ FPDMA QUEUED Error 240 [19] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6a 00 1d 29 00 00 Error: UNC at LBA = 0x6a001d29 = 1778392361 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 6a 00 1d 08 40 00 02:11:56.498 READ FPDMA QUEUED 60 00 00 00 08 00 00 6a 00 1d 00 40 00 02:11:56.373 READ FPDMA QUEUED 60 00 00 00 08 00 00 69 00 1d f8 40 00 02:11:56.373 READ FPDMA QUEUED 60 00 00 00 08 00 00 69 00 1d a8 40 00 02:11:55.881 READ FPDMA QUEUED 60 00 00 00 08 00 00 69 00 1d a0 40 00 02:11:55.830 READ FPDMA QUEUED Error 239 [18] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6a 00 1d 00 00 00 Error: UNC at LBA = 0x6a001d00 = 1778392320 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 00 69 00 1d a0 40 00 02:11:52.799 READ FPDMA QUEUED 60 00 00 00 80 00 00 69 00 1d 20 40 00 02:11:52.465 READ FPDMA QUEUED 60 00 00 00 80 00 00 68 00 1d a0 40 00 02:11:52.452 READ FPDMA QUEUED 60 00 00 00 18 00 05 52 00 89 08 40 00 02:11:52.452 READ FPDMA QUEUED 60 00 00 00 70 00 0c 37 00 07 e0 40 00 02:11:52.451 READ FPDMA QUEUED Error 238 [17] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 55 00 81 ef 00 00 Error: UNC at LBA = 0x550081ef = 1426096623 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 55 00 81 00 40 00 01:36:03.767 READ FPDMA QUEUED 60 00 00 00 02 00 00 55 00 81 04 40 00 01:36:03.724 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:36:03.648 READ LOG EXT 60 00 00 01 00 00 00 55 00 81 00 40 00 01:36:00.661 READ FPDMA QUEUED 60 00 00 00 02 00 00 55 00 81 02 40 00 01:36:00.617 READ FPDMA QUEUED Error 237 [16] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 55 00 81 ef 00 00 Error: UNC at LBA = 0x550081ef = 1426096623 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 55 00 81 00 40 00 01:36:00.661 READ FPDMA QUEUED 60 00 00 00 02 00 00 55 00 81 02 40 00 01:36:00.617 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:36:00.541 READ LOG EXT 60 00 00 01 00 00 00 55 00 81 00 40 00 01:35:57.554 READ FPDMA QUEUED 60 00 00 00 02 00 00 55 00 81 00 40 00 01:35:57.511 READ FPDMA QUEUED Error 236 [15] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 55 00 81 ef 00 00 Error: UNC at LBA = 0x550081ef = 1426096623 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 55 00 81 00 40 00 01:35:57.554 READ FPDMA QUEUED 60 00 00 00 02 00 00 55 00 81 00 40 00 01:35:57.511 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:35:57.426 READ LOG EXT 60 00 00 01 00 00 00 55 00 81 00 40 00 01:35:54.495 READ FPDMA QUEUED 60 00 00 01 00 00 00 57 00 81 00 40 00 01:35:54.490 READ FPDMA QUEUED Error 235 [14] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 55 00 81 ef 00 00 Error: UNC at LBA = 0x550081ef = 1426096623 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 55 00 81 00 40 00 01:35:54.495 READ FPDMA QUEUED 60 00 00 01 00 00 00 57 00 81 00 40 00 01:35:54.490 READ FPDMA QUEUED 60 00 00 01 00 00 00 56 00 81 00 40 00 01:35:54.443 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:35:54.353 READ LOG EXT 60 00 00 01 00 00 00 55 00 81 00 40 00 01:35:51.411 READ FPDMA QUEUED Error 234 [13] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 55 00 81 ef 00 00 Error: UNC at LBA = 0x550081ef = 1426096623 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 55 00 81 00 40 00 01:35:51.411 READ FPDMA QUEUED 60 00 00 01 00 00 00 fb 00 fd 00 40 00 01:35:51.364 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:35:51.288 READ LOG EXT 60 00 00 01 00 00 00 55 00 81 00 40 00 01:35:48.326 READ FPDMA QUEUED 60 00 00 01 00 00 00 53 00 81 00 40 00 01:35:48.321 READ FPDMA QUEUED Error 233 [12] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 55 00 81 ef 00 00 Error: UNC at LBA = 0x550081ef = 1426096623 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 55 00 81 00 40 00 01:35:48.326 READ FPDMA QUEUED 60 00 00 01 00 00 00 53 00 81 00 40 00 01:35:48.321 READ FPDMA QUEUED 60 00 00 01 00 00 00 52 00 81 00 40 00 01:35:48.320 READ FPDMA QUEUED 60 00 00 01 00 00 00 7f 00 89 00 40 00 01:35:48.313 READ FPDMA QUEUED 60 00 00 01 00 00 00 3e 00 84 00 40 00 01:35:48.298 READ FPDMA QUEUED Error 232 [11] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f1 00 80 4f 00 00 Error: UNC at LBA = 0xf100804f = 4043341903 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 f1 00 80 00 40 00 01:35:42.464 READ FPDMA QUEUED 60 00 00 00 02 00 00 f1 00 80 de 40 00 01:35:42.418 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:35:42.342 READ LOG EXT 60 00 00 01 00 00 00 f1 00 80 00 40 00 01:35:39.491 READ FPDMA QUEUED 60 00 00 00 02 00 00 f1 00 80 dc 40 00 01:35:39.436 READ FPDMA QUEUED Error 231 [10] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f1 00 80 4e 00 00 Error: UNC at LBA = 0xf100804e = 4043341902 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 f1 00 80 00 40 00 01:35:39.491 READ FPDMA QUEUED 60 00 00 00 02 00 00 f1 00 80 dc 40 00 01:35:39.436 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:35:39.361 READ LOG EXT 60 00 00 01 00 00 00 f1 00 80 00 40 00 01:35:36.484 READ FPDMA QUEUED 60 00 00 00 02 00 00 f1 00 80 da 40 00 01:35:36.429 READ FPDMA QUEUED Error 230 [9] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f1 00 80 4e 00 00 Error: UNC at LBA = 0xf100804e = 4043341902 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 f1 00 80 00 40 00 01:35:36.484 READ FPDMA QUEUED 60 00 00 00 02 00 00 f1 00 80 da 40 00 01:35:36.429 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:35:36.345 READ LOG EXT 60 00 00 01 00 00 00 f1 00 80 00 40 00 01:35:33.494 READ FPDMA QUEUED 60 00 00 00 02 00 00 f1 00 80 d8 40 00 01:35:33.448 READ FPDMA QUEUED Error 229 [8] occurred at disk power-on lifetime: 18270 hours (761 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f1 00 80 4e 00 00 Error: UNC at LBA = 0xf100804e = 4043341902 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 f1 00 80 00 40 00 01:35:33.494 READ FPDMA QUEUED 60 00 00 00 02 00 00 f1 00 80 d8 40 00 01:35:33.448 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:35:33.364 READ LOG EXT 60 00 00 01 00 00 00 f1 00 80 00 40 00 01:35:30.487 READ FPDMA QUEUED 60 00 00 00 02 00 00 f1 00 80 d6 40 00 01:35:30.432 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 90% 18609 335888 # 2 Short offline Interrupted (host reset) 00% 18606 - # 3 Short offline Completed: electrical failure 90% 18286 0 # 4 Short offline Completed: electrical failure 90% 18284 0 # 5 Short offline Completed: electrical failure 90% 18284 0 # 6 Short offline Completed: electrical failure 90% 18283 0 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 39/40 Celsius Lifetime Min/Max Temperature: 8/45 Celsius Under/Over Temperature Limit Count: 0/191 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (60) Index Estimated Time Temperature Celsius 61 2022-02-12 12:02 40 ********************* ... ..(112 skipped). .. ********************* 46 2022-02-12 13:55 40 ********************* 47 2022-02-12 13:56 39 ******************** 48 2022-02-12 13:57 39 ******************** 49 2022-02-12 13:58 40 ********************* ... ..( 3 skipped). .. ********************* 53 2022-02-12 14:02 40 ********************* 54 2022-02-12 14:03 39 ******************** ... ..( 3 skipped). .. ******************** 58 2022-02-12 14:07 39 ******************** 59 2022-02-12 14:08 40 ********************* 60 2022-02-12 14:09 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS