smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p10 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: HGST HUS726T4TALA6L4 Serial Number: V1JJNVMH LU WWN Device Id: 5 000cca 0bce3c33f Firmware Version: VLGNW984 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Dec 10 12:38:46 2021 +04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 87) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 530) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 128 128 054 - 108 3 Spin_Up_Time POS--- 100 100 024 - 0 4 Start_Stop_Count -O--C- 100 100 000 - 3 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 128 128 020 - 18 9 Power_On_Hours -O--C- 100 100 000 - 6287 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 3 192 Power-Off_Retract_Count -O--CK 100 100 000 - 262 193 Load_Cycle_Count -O--C- 100 100 000 - 262 194 Temperature_Celsius -O---- 187 187 000 - 32 (Min/Max 19/39) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 688 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL R/W 1 Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 5 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 [0] occurred at disk power-on lifetime: 6279 hours (261 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 00 00 00 00 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 43 00 30 00 00 3a 67 6c cf 40 08 48d+18:00:44.295 READ FPDMA QUEUED 60 00 01 00 38 00 00 bc 69 4e 75 40 08 48d+18:00:41.700 READ FPDMA QUEUED b0 00 d0 00 01 00 00 00 c2 4f 00 40 08 48d+18:00:41.696 SMART READ DATA 2f 00 00 00 01 00 00 00 00 00 10 00 08 48d+18:00:41.696 READ LOG EXT 60 00 01 00 18 00 00 bc 69 4e 75 40 08 48d+18:00:39.096 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 6279 hours (261 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 00 00 00 00 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 43 00 10 00 00 3a 67 6c cf 40 08 48d+18:00:41.695 READ FPDMA QUEUED 60 00 01 00 18 00 00 bc 69 4e 75 40 08 48d+18:00:39.096 READ FPDMA QUEUED ec 00 00 00 01 00 00 00 00 00 00 40 08 48d+18:00:39.096 IDENTIFY DEVICE 2f 00 00 00 01 00 00 00 00 00 10 00 08 48d+18:00:39.096 READ LOG EXT 60 00 01 00 f8 00 00 bc 69 4e 75 40 08 48d+18:00:36.513 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 6279 hours (261 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 00 00 00 00 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 43 00 f0 00 00 3a 67 6c cf 40 08 48d+18:00:39.095 READ FPDMA QUEUED 60 00 01 00 f8 00 00 bc 69 4e 75 40 08 48d+18:00:36.513 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 40 08 48d+18:00:36.513 CHECK POWER MODE 2f 00 00 00 01 00 00 00 00 00 10 00 08 48d+18:00:36.512 READ LOG EXT 61 00 01 00 d8 00 00 19 ff c0 ba 40 08 48d+18:00:34.947 WRITE FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 6279 hours (261 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 00 00 00 00 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 43 00 18 00 00 3a 67 6c cf 40 08 48d+18:00:36.512 READ FPDMA QUEUED 61 00 01 00 d8 00 00 19 ff c0 ba 40 08 48d+18:00:34.947 WRITE FPDMA QUEUED 61 00 01 00 d0 00 00 19 ff c0 b4 40 08 48d+18:00:34.947 WRITE FPDMA QUEUED 61 00 01 00 c8 00 01 95 db 2f a3 40 08 48d+18:00:34.947 WRITE FPDMA QUEUED 61 00 02 00 c0 00 01 13 5b 41 33 40 08 48d+18:00:34.946 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 6287 - # 2 Short offline Completed without error 00% 6286 - # 3 Short offline Completed without error 00% 6281 - # 4 Short offline Completed without error 00% 6257 - # 5 Short offline Completed without error 00% 6233 - # 6 Short offline Completed without error 00% 6209 - # 7 Short offline Completed without error 00% 6185 - # 8 Extended offline Completed without error 00% 6173 - # 9 Short offline Completed without error 00% 6161 - #10 Short offline Completed without error 00% 6137 - #11 Short offline Completed without error 00% 6113 - #12 Short offline Completed without error 00% 6089 - #13 Short offline Completed without error 00% 6065 - #14 Short offline Completed without error 00% 6041 - #15 Short offline Completed without error 00% 6017 - #16 Extended offline Completed without error 00% 6005 - #17 Short offline Completed without error 00% 5993 - #18 Short offline Completed without error 00% 5969 - #19 Short offline Completed without error 00% 5945 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 29/34 Celsius Lifetime Min/Max Temperature: 19/39 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (62) Index Estimated Time Temperature Celsius 63 2021-12-10 10:31 32 ************* 64 2021-12-10 10:32 31 ************ ... ..( 21 skipped). .. ************ 86 2021-12-10 10:54 31 ************ 87 2021-12-10 10:55 32 ************* ... ..(101 skipped). .. ************* 61 2021-12-10 12:37 32 ************* 62 2021-12-10 12:38 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 3 --- Lifetime Power-On Resets 0x01 0x010 4 6287 --- Power-on Hours 0x01 0x018 6 21048197162 --- Logical Sectors Written 0x01 0x020 6 315049273 --- Number of Write Commands 0x01 0x028 6 27469544503 --- Logical Sectors Read 0x01 0x030 6 179668029 --- Number of Read Commands 0x01 0x038 6 22635751350 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 6230 --- Spindle Motor Power-on Hours 0x03 0x010 4 6230 --- Head Flying Hours 0x03 0x018 4 262 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 90 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 5 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 32 --- Current Temperature 0x05 0x010 1 31 N-- Average Short Term Temperature 0x05 0x018 1 30 N-- Average Long Term Temperature 0x05 0x020 1 39 --- Highest Temperature 0x05 0x028 1 19 --- Lowest Temperature 0x05 0x030 1 36 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 34 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 10 --- Number of Hardware Resets 0x06 0x010 4 3 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 11 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS