smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.9.0-0.bpo.5-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WD3000FYYZ-23UL 81Y9799 81Y3865IBM Firmware Version: WD40 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Jan 23 12:16:40 2021 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 246) Self-test routine in progress... 60% of test remaining. Total time to complete Offline data collection: (36000) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 389) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 191 051 - 0 3 Spin_Up_Time POS--K 227 227 021 - 7616 4 Start_Stop_Count -O--CK 100 100 000 - 45 5 Reallocated_Sector_Ct PO--CK 199 199 140 - 53 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 072 072 000 - 20557 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 45 16 Unknown_Attribute -O---K 047 153 000 - 2573469547285 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 200 000 - 43 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 116 111 000 - 36 195 Hardware_ECC_Recovered -OS-CK 200 200 000 - 0 196 Reallocated_Event_Count -O--CK 199 199 000 - 1 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb1 GPL,SL VS 1 Device vendor specific log 0xb2 GPL VS 65535 Device vendor specific log 0xb2 SL VS 255 Device vendor specific log 0xb3-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xd0 GPL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 47 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 47 [22] occurred at disk power-on lifetime: 20495 hours (853 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 17 3a ed 13 40 00 Error: UNC at LBA = 0x1173aed13 = 4684705043 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 01 17 3a ed 00 40 00 1d+16:37:35.435 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 3a ec 00 40 00 1d+16:37:35.434 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 3a eb 00 40 00 1d+16:37:35.433 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 3a ea 00 40 00 1d+16:37:35.432 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 3a e9 00 40 00 1d+16:37:35.430 READ FPDMA QUEUED Error 46 [21] occurred at disk power-on lifetime: 18318 hours (763 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 10 00 00 01 17 3a bc 97 40 00 Error: UNC at LBA = 0x1173abc97 = 4684692631 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 10 00 00 01 17 3a b0 00 40 00 23d+06:42:45.164 READ VERIFY SECTOR(S) EXT 42 00 00 10 00 00 01 17 3a a0 00 40 00 23d+06:42:45.070 READ VERIFY SECTOR(S) EXT 42 00 00 10 00 00 01 17 3a 90 00 40 00 23d+06:42:45.051 READ VERIFY SECTOR(S) EXT 42 00 00 10 00 00 01 17 3a 80 00 40 00 23d+06:42:45.036 READ VERIFY SECTOR(S) EXT 42 00 00 10 00 00 01 17 3a 70 00 40 00 23d+06:42:45.020 READ VERIFY SECTOR(S) EXT Error 45 [20] occurred at disk power-on lifetime: 17815 hours (742 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 10 00 00 01 17 3a b5 b8 40 00 Error: UNC at LBA = 0x1173ab5b8 = 4684690872 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 10 00 00 01 17 3a b0 00 40 00 2d+07:40:23.347 READ VERIFY SECTOR(S) EXT 42 00 00 10 00 00 01 17 3a a0 00 40 00 2d+07:40:23.253 READ VERIFY SECTOR(S) EXT 42 00 00 10 00 00 01 17 3a 90 00 40 00 2d+07:40:23.234 READ VERIFY SECTOR(S) EXT 42 00 00 10 00 00 01 17 3a 80 00 40 00 2d+07:40:23.218 READ VERIFY SECTOR(S) EXT 42 00 00 10 00 00 01 17 3a 70 00 40 00 2d+07:40:23.202 READ VERIFY SECTOR(S) EXT Error 44 [19] occurred at disk power-on lifetime: 17809 hours (742 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 17 1d 43 a7 40 00 Error: UNC at LBA = 0x1171d43a7 = 4682761127 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 01 17 1d 43 00 40 00 2d+01:08:38.669 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 1d 42 00 40 00 2d+01:08:38.668 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 1d 41 00 40 00 2d+01:08:38.667 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 1d 40 00 40 00 2d+01:08:38.666 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 1d 3f 00 40 00 2d+01:08:38.664 READ FPDMA QUEUED Error 43 [18] occurred at disk power-on lifetime: 17662 hours (735 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 17 3a b5 b8 40 00 Error: UNC at LBA = 0x1173ab5b8 = 4684690872 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 08 00 01 17 3a b6 00 40 00 45d+14:59:02.371 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 3a b5 00 40 00 45d+14:59:02.368 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 3a b3 00 40 00 45d+14:59:02.362 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 3a b2 00 40 00 45d+14:59:02.359 READ FPDMA QUEUED 60 01 00 00 08 00 01 17 3a b1 00 40 00 45d+14:59:02.357 READ FPDMA QUEUED Error 42 [17] occurred at disk power-on lifetime: 17641 hours (735 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 17 1d 28 2a 40 00 Error: UNC at LBA = 0x1171d282a = 4682754090 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 01 17 1d 28 00 40 00 44d+18:16:44.446 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 1d 27 00 40 00 44d+18:16:44.445 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 1d 26 00 40 00 44d+18:16:44.443 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 1d 25 00 40 00 44d+18:16:44.442 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 1d 24 00 40 00 44d+18:16:44.441 READ FPDMA QUEUED Error 41 [16] occurred at disk power-on lifetime: 16641 hours (693 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 17 1d 05 6c 40 00 Error: UNC at LBA = 0x1171d056c = 4682745196 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 98 00 08 00 01 17 1d 05 68 40 00 3d+01:50:29.423 READ FPDMA QUEUED 60 00 68 00 00 00 01 17 1d 05 00 40 00 3d+01:50:29.423 READ FPDMA QUEUED 42 00 00 10 00 00 00 21 d6 d0 00 40 00 3d+01:50:29.394 READ VERIFY SECTOR(S) EXT 60 01 00 00 00 00 01 17 1d 08 00 40 00 3d+01:50:29.392 READ FPDMA QUEUED 60 00 6c 00 10 00 01 17 1d 05 00 40 00 3d+01:50:29.369 READ FPDMA QUEUED Error 40 [15] occurred at disk power-on lifetime: 16641 hours (693 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 17 1d 05 6c 40 00 Error: UNC at LBA = 0x1171d056c = 4682745196 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 01 17 1d 05 00 40 00 3d+01:50:27.549 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 1d 04 00 40 00 3d+01:50:27.545 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 1d 03 00 40 00 3d+01:50:27.542 READ FPDMA QUEUED 60 01 00 00 00 00 01 17 1d 01 00 40 00 3d+01:50:27.536 READ FPDMA QUEUED 60 01 00 00 08 00 01 17 1d 00 00 40 00 3d+01:50:27.535 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Self-test routine in progress 60% 20557 - # 2 Extended offline Completed without error 00% 20548 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: DST executing in background (3) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 31/40 Celsius Lifetime Min/Max Temperature: 21/41 Celsius Specified Max Operating Temperature: 60 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (244) Index Estimated Time Temperature Celsius 245 2021-01-23 04:19 36 ***************** ... ..(476 skipped). .. ***************** 244 2021-01-23 12:16 36 ***************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 45 --- Lifetime Power-On Resets 0x01 0x010 4 20557 --- Power-on Hours 0x01 0x018 6 1556262443474 --- Logical Sectors Written 0x01 0x020 6 942684715 --- Number of Write Commands 0x01 0x028 6 1017207103832 --- Logical Sectors Read 0x01 0x030 6 4152049099 --- Number of Read Commands 0x01 0x048 2 4791 N-- Workload Utilization 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 20377 --- Spindle Motor Power-on Hours 0x03 0x010 4 20377 --- Head Flying Hours 0x03 0x018 4 45 --- Head Load Events 0x03 0x020 4 199 N-- Number of Reallocated Logical Sectors 0x03 0x028 4 528 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 47 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 39 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 36 --- Current Temperature 0x05 0x010 1 36 --- Average Short Term Temperature 0x05 0x018 1 32 --- Average Long Term Temperature 0x05 0x020 1 39 --- Highest Temperature 0x05 0x028 1 27 --- Lowest Temperature 0x05 0x030 1 36 --- Highest Average Short Term Temperature 0x05 0x038 1 31 --- Lowest Average Short Term Temperature 0x05 0x040 1 35 --- Highest Average Long Term Temperature 0x05 0x048 1 32 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 109 --- Number of Hardware Resets 0x06 0x010 4 42 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 90199 Vendor specific