smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.3.0-62-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Xmore pSLC NAND Industrial M.2 2280 SATA SSD add by REA GmbH Device Model: M2CA032GXAIMS-003Z Serial Number: 6891079C021700059826 LU WWN Device Id: 0 000000 000000000 Firmware Version: XP01.1GB User Capacity: 32.017.047.552 bytes [32,0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: M.2 Device is: In smartctl database [for details use: -P show] ATA Version is: Unknown(0x0ff8) (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Jul 14 19:07:05 2020 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 568 12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 22756 168 SATA_PHY_Err_Ct 0x0012 100 100 000 Old_age Always - 0 169 NA 0x0000 100 100 000 Old_age Offline - 8 170 Bad_Blk_Ct_Erl/Lat 0x0003 092 092 010 Pre-fail Always - 0/50 173 MaxAvgErase_Ct 0x0012 100 100 000 Old_age Always - 600 (Average 489) 192 Unexpect_Power_Loss_Ct 0x0012 100 100 000 Old_age Always - 22685 218 SATA_CRC_Error_Count 0x000b 100 100 050 Pre-fail Always - 1 231 Perc_Rated_Life_Remain 0x0013 100 100 000 Pre-fail Always - 97 241 Host_Writes_GiB 0x0032 100 100 000 Old_age Always - 14248 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 567 - # 2 Short offline Completed without error 00% 566 - # 3 Short offline Completed without error 00% 566 - # 4 Short offline Completed without error 00% 566 - # 5 Short offline Completed without error 00% 566 - # 6 Short offline Completed without error 00% 566 - # 7 Short offline Completed without error 00% 566 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.