smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.2-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: HUA723020ALA640 Serial Number: YFKSAHWG Firmware Version: MK7OAAA0 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Thu May 23 15:27:07 2019 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (18950) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 316) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 134 134 054 - 89 3 Spin_Up_Time POS--- 127 127 024 - 491 (Average 492) 4 Start_Stop_Count -O--C- 100 100 000 - 125 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 123 123 020 - 31 9 Power_On_Hours -O--C- 096 096 000 - 30017 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 124 192 Power-Off_Retract_Count -O--CK 100 100 000 - 224 193 Load_Cycle_Count -O--C- 100 100 000 - 224 194 Temperature_Celsius -O---- 176 176 000 - 34 (Min/Max 21/47) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 63 Current Device Internal Status Data log 0x80 GPL R/W 63 Host vendor specific log 0x81-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 29870 hours (1244 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 5d 00 00 00 d9 29 4b 00 00 Error: ICRC, ABRT at LBA = 0x00d9294b = 14231883 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 03 ff 00 00 00 00 00 d9 25 a9 40 00 00:21:14.112 WRITE FPDMA QUEUED 61 03 ff 00 00 00 00 00 d9 21 aa 40 00 00:21:14.108 WRITE FPDMA QUEUED 61 03 ff 00 00 00 00 00 d9 1d ab 40 00 00:21:14.104 WRITE FPDMA QUEUED 61 03 ff 00 00 00 00 00 d9 19 ac 40 00 00:21:14.101 WRITE FPDMA QUEUED 61 03 ff 00 00 00 00 00 d9 15 ad 40 00 00:21:14.097 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 30017 - # 2 Extended offline Completed without error 00% 29999 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 27/34 Celsius Lifetime Min/Max Temperature: 21/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (48) Index Estimated Time Temperature Celsius 49 2019-05-23 13:20 34 *************** 50 2019-05-23 13:21 34 *************** 51 2019-05-23 13:22 33 ************** ... ..( 6 skipped). .. ************** 58 2019-05-23 13:29 33 ************** 59 2019-05-23 13:30 34 *************** ... ..( 3 skipped). .. *************** 63 2019-05-23 13:34 34 *************** 64 2019-05-23 13:35 33 ************** ... ..( 7 skipped). .. ************** 72 2019-05-23 13:43 33 ************** 73 2019-05-23 13:44 34 *************** 74 2019-05-23 13:45 33 ************** ... ..( 3 skipped). .. ************** 78 2019-05-23 13:49 33 ************** 79 2019-05-23 13:50 ? - 80 2019-05-23 13:51 31 ************ 81 2019-05-23 13:52 31 ************ 82 2019-05-23 13:53 32 ************* ... ..( 9 skipped). .. ************* 92 2019-05-23 14:03 32 ************* 93 2019-05-23 14:04 33 ************** 94 2019-05-23 14:05 32 ************* 95 2019-05-23 14:06 33 ************** ... ..( 9 skipped). .. ************** 105 2019-05-23 14:16 33 ************** 106 2019-05-23 14:17 ? - 107 2019-05-23 14:18 30 *********** 108 2019-05-23 14:19 30 *********** 109 2019-05-23 14:20 31 ************ ... ..( 4 skipped). .. ************ 114 2019-05-23 14:25 31 ************ 115 2019-05-23 14:26 32 ************* ... ..( 5 skipped). .. ************* 121 2019-05-23 14:32 32 ************* 122 2019-05-23 14:33 ? - 123 2019-05-23 14:34 ? - 124 2019-05-23 14:35 27 ******** 125 2019-05-23 14:36 28 ********* 126 2019-05-23 14:37 28 ********* 127 2019-05-23 14:38 29 ********** ... ..( 2 skipped). .. ********** 2 2019-05-23 14:41 29 ********** 3 2019-05-23 14:42 30 *********** 4 2019-05-23 14:43 30 *********** 5 2019-05-23 14:44 30 *********** 6 2019-05-23 14:45 31 ************ ... ..( 3 skipped). .. ************ 10 2019-05-23 14:49 31 ************ 11 2019-05-23 14:50 32 ************* ... ..( 7 skipped). .. ************* 19 2019-05-23 14:58 32 ************* 20 2019-05-23 14:59 33 ************** ... ..( 5 skipped). .. ************** 26 2019-05-23 15:05 33 ************** 27 2019-05-23 15:06 34 *************** 28 2019-05-23 15:07 33 ************** ... ..( 3 skipped). .. ************** 32 2019-05-23 15:11 33 ************** 33 2019-05-23 15:12 34 *************** ... ..( 14 skipped). .. *************** 48 2019-05-23 15:27 34 *************** SCT Error Recovery Control: Read: 140 (14.0 seconds) Write: 140 (14.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 124 --- Lifetime Power-On Resets 0x01 0x010 4 30017 --- Power-on Hours 0x01 0x018 6 223005734345 --- Logical Sectors Written 0x01 0x020 6 1821984989 --- Number of Write Commands 0x01 0x028 6 1037672941575 --- Logical Sectors Read 0x01 0x030 6 6142558541 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 30006 --- Spindle Motor Power-on Hours 0x03 0x010 4 30006 --- Head Flying Hours 0x03 0x018 4 224 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 1 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 34 --- Current Temperature 0x05 0x010 1 34 N-- Average Short Term Temperature 0x05 0x018 1 35 N-- Average Long Term Temperature 0x05 0x020 1 47 --- Highest Temperature 0x05 0x028 1 21 --- Lowest Temperature 0x05 0x030 1 41 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 37 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 676413 --- Number of Hardware Resets 0x06 0x010 4 270 --- Number of ASR Events 0x06 0x018 4 1 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 8 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS