smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.51-ck1] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Corsair Force LE SSD Firmware Version: SAFC11.0 User Capacity: 240.057.409.536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Jul 15 12:27:57 2020 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 30) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 203 5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 12792 12 Power_Cycle_Count -O--C- 100 100 000 - 4648 162 Unknown_Attribute PO---- 100 100 000 - 290 170 Unknown_Attribute -O---- 100 100 000 - 0 173 Unknown_Attribute -O--C- 100 100 000 - 1310812 174 Unknown_Attribute -O--C- 100 100 000 - 76 181 Program_Fail_Cnt_Total -O--C- 100 100 000 - 0 187 Reported_Uncorrect -O--C- 100 100 000 - 203 192 Power-Off_Retract_Count -O--C- 100 100 000 - 76 194 Temperature_Celsius PO---K 070 070 030 - 30 (Min/Max 30/30) 196 Reallocated_Event_Count -O---- 100 100 010 - 0 218 Unknown_Attribute PO-R-- 100 100 050 - 0 231 Temperature_Celsius PO--C- 100 100 000 - 100 241 Total_LBAs_Written -O--C- 100 100 000 - 6517 242 Total_LBAs_Read -O--C- 100 100 000 - 26915 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 6 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 203 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 203 [202] occurred at disk power-on lifetime: 12627 hours (526 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 a8 00 00 0e d1 3b f9 40 00 Error: UNC at LBA = 0x0ed13bf9 = 248593401 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 a8 00 00 0e d1 3b f9 40 08 00:00:07.703 READ FPDMA QUEUED 60 00 a8 00 a0 00 00 03 08 1d 07 40 08 00:00:05.957 READ FPDMA QUEUED 60 00 79 00 98 00 00 03 08 1b f6 40 08 00:00:05.956 READ FPDMA QUEUED 60 00 98 00 90 00 00 03 08 1c 6f 40 08 00:00:05.955 READ FPDMA QUEUED 60 00 b1 00 88 00 00 03 08 1e 51 40 08 00:00:05.955 READ FPDMA QUEUED Error 202 [201] occurred at disk power-on lifetime: 12614 hours (525 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 48 00 00 03 ca 2d dc 40 00 Error: UNC at LBA = 0x03ca2ddc = 63581660 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 04 00 48 00 00 03 ca 2d dc 40 08 00:01:54.395 READ FPDMA QUEUED 60 00 3a 00 40 00 00 03 c9 d7 dd 40 08 00:01:53.443 READ FPDMA QUEUED 60 00 1d 00 38 00 00 03 c9 d7 c0 40 08 00:01:53.442 READ FPDMA QUEUED 60 00 1d 00 30 00 00 03 c9 d7 a3 40 08 00:01:53.442 READ FPDMA QUEUED 60 00 1d 00 28 00 00 03 c9 d7 86 40 08 00:01:53.442 READ FPDMA QUEUED Error 201 [200] occurred at disk power-on lifetime: 12581 hours (524 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 40 00 00 02 12 d5 fb 40 00 Error: UNC at LBA = 0x0212d5fb = 34788859 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 02 12 d5 fb 40 08 01:00:50.702 READ FPDMA QUEUED 60 00 08 00 38 00 00 02 12 d6 03 40 08 01:00:50.702 READ FPDMA QUEUED 60 00 09 00 30 00 00 02 18 2b 7b 40 08 01:00:50.693 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 01:00:47.914 FLUSH CACHE EXT 61 00 08 00 20 00 00 02 1d 94 fc 40 08 01:00:47.914 WRITE FPDMA QUEUED Error 200 [199] occurred at disk power-on lifetime: 12221 hours (509 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 e0 00 00 15 f3 44 76 40 00 Error: UNC at LBA = 0x15f34476 = 368264310 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 0c 00 e0 00 00 15 f3 44 76 40 08 04:04:14.402 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 04:04:13.490 FLUSH CACHE EXT 61 00 02 00 d0 00 00 1b f2 43 92 40 08 04:04:13.490 WRITE FPDMA QUEUED 61 00 02 00 c8 00 00 1b f2 41 92 40 08 04:04:13.490 WRITE FPDMA QUEUED 61 00 02 00 c0 00 00 00 10 0b 92 40 08 04:04:13.490 WRITE FPDMA QUEUED Error 199 [198] occurred at disk power-on lifetime: 12179 hours (507 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 10 00 00 11 ea fb 51 40 00 Error: UNC at LBA = 0x11eafb51 = 300612433 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 10 00 00 11 ea fb 51 40 08 06:21:46.842 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 06:21:45.686 FLUSH CACHE EXT 61 00 02 00 00 00 00 1b f2 43 e4 40 08 06:21:45.686 WRITE FPDMA QUEUED 61 00 02 00 f0 00 00 1b f2 41 e4 40 08 06:21:45.686 WRITE FPDMA QUEUED 61 00 02 00 e8 00 00 00 10 0b e4 40 08 06:21:45.686 WRITE FPDMA QUEUED Error 198 [197] occurred at disk power-on lifetime: 12124 hours (505 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 38 00 00 0f 72 2d 9a 40 00 Error: UNC at LBA = 0x0f722d9a = 259141018 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 0f 00 38 00 00 0f 72 2d 9a 40 08 00:19:23.930 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:19:22.621 FLUSH CACHE EXT 61 00 08 00 28 00 00 0f 55 5d e5 40 08 00:19:22.621 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:19:22.619 FLUSH CACHE EXT 61 00 30 00 18 00 00 0f 55 5d 9d 40 08 00:19:22.619 WRITE FPDMA QUEUED Error 197 [196] occurred at disk power-on lifetime: 12072 hours (503 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 b8 00 00 0c 6d 4e 9b 40 00 Error: UNC at LBA = 0x0c6d4e9b = 208490139 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 0f 00 b8 00 00 0c 6d 4e 9b 40 08 01:43:01.987 READ FPDMA QUEUED 60 00 99 00 b0 00 00 07 28 a6 3e 40 08 01:42:58.574 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 01:42:57.662 FLUSH CACHE EXT 61 00 02 00 a0 00 00 1b f2 43 3c 40 08 01:42:57.662 WRITE FPDMA QUEUED 61 00 02 00 98 00 00 1b f2 41 3c 40 08 01:42:57.662 WRITE FPDMA QUEUED Error 196 [195] occurred at disk power-on lifetime: 12061 hours (502 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 78 00 00 0b 7e a0 0c 40 00 Error: UNC at LBA = 0x0b7ea00c = 192847884 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 78 00 00 0b 7e a0 0c 40 08 00:17:48.148 READ FPDMA QUEUED 60 00 c1 00 70 00 00 03 14 96 42 40 08 00:17:47.231 READ FPDMA QUEUED 60 00 02 00 68 00 00 03 14 97 0b 40 08 00:17:47.231 READ FPDMA QUEUED 60 00 02 00 60 00 00 03 14 80 35 40 08 00:17:47.228 READ FPDMA QUEUED 60 00 a3 00 58 00 00 07 56 78 02 40 08 00:17:47.223 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 12792 - # 2 Short offline Completed without error 00% 7990 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 4648 --- Lifetime Power-On Resets 0x01 0x010 4 12792 --- Power-on Hours 0x01 0x018 6 13669114069 --- Logical Sectors Written 0x01 0x020 6 253277446 --- Number of Write Commands 0x01 0x028 6 56445533223 --- Logical Sectors Read 0x01 0x030 6 938738618 --- Number of Read Commands 0x01 0x038 6 46052054171 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 118198 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 22 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 32 --- Current Temperature 0x05 0x010 1 32 --- Average Short Term Temperature 0x05 0x018 1 32 --- Average Long Term Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 5 --- Lowest Temperature 0x05 0x030 1 50 --- Highest Average Short Term Temperature 0x05 0x038 1 16 --- Lowest Average Short Term Temperature 0x05 0x040 1 50 --- Highest Average Long Term Temperature 0x05 0x048 1 16 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 50 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 11686 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 3 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 48136592 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 16010 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC