smartctl 6.6 2016-05-31 r4324 [armv7l-linux-4.14.34-1-osmc] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD8003FRYZ-01JPDB1 Firmware Version: 01.01H02 User Capacity: 8.001.563.222.016 bytes [8,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon May 21 15:38:46 2018 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 93) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (1096) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 130 130 054 - 108 3 Spin_Up_Time POS--- 145 145 024 - 453 (Average 453) 4 Start_Stop_Count -O--C- 100 100 000 - 44 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 128 128 020 - 18 9 Power_On_Hours -O--C- 100 100 000 - 102 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 7 22 Unknown_Attribute PO---K 100 100 025 - 100 192 Power-Off_Retract_Count -O--CK 100 100 000 - 46 193 Load_Cycle_Count -O--C- 100 100 000 - 46 194 Temperature_Celsius -O---- 206 206 000 - 29 (Min/Max 16/31) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 5501 Pending Defects log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ NON-DATA log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL R/W 1 SATA Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 102 - # 2 Short offline Completed without error 00% 101 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 0 Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 22/31 Celsius Lifetime Min/Max Temperature: 16/31 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (4) Index Estimated Time Temperature Celsius 5 2018-05-21 13:31 25 ****** ... ..( 57 skipped). .. ****** 63 2018-05-21 14:29 25 ****** 64 2018-05-21 14:30 26 ******* 65 2018-05-21 14:31 26 ******* 66 2018-05-21 14:32 26 ******* 67 2018-05-21 14:33 27 ******** 68 2018-05-21 14:34 28 ********* ... ..( 3 skipped). .. ********* 72 2018-05-21 14:38 28 ********* 73 2018-05-21 14:39 29 ********** ... ..( 4 skipped). .. ********** 78 2018-05-21 14:44 29 ********** 79 2018-05-21 14:45 30 *********** 80 2018-05-21 14:46 30 *********** 81 2018-05-21 14:47 29 ********** ... ..( 2 skipped). .. ********** 84 2018-05-21 14:50 29 ********** 85 2018-05-21 14:51 28 ********* ... ..( 3 skipped). .. ********* 89 2018-05-21 14:55 28 ********* 90 2018-05-21 14:56 27 ******** ... ..( 6 skipped). .. ******** 97 2018-05-21 15:03 27 ******** 98 2018-05-21 15:04 26 ******* ... ..( 6 skipped). .. ******* 105 2018-05-21 15:11 26 ******* 106 2018-05-21 15:12 27 ******** 107 2018-05-21 15:13 27 ******** 108 2018-05-21 15:14 28 ********* ... ..( 2 skipped). .. ********* 111 2018-05-21 15:17 28 ********* 112 2018-05-21 15:18 29 ********** ... ..( 4 skipped). .. ********** 117 2018-05-21 15:23 29 ********** 118 2018-05-21 15:24 30 *********** 119 2018-05-21 15:25 29 ********** ... ..( 2 skipped). .. ********** 122 2018-05-21 15:28 29 ********** 123 2018-05-21 15:29 28 ********* ... ..( 7 skipped). .. ********* 3 2018-05-21 15:37 28 ********* 4 2018-05-21 15:38 25 ****** SMART WRITE LOG does not return COUNT and LBA_LOW register SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 112 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 112 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS