Custom Query (1359 matches)
Results (76 - 78 of 1359)
| Ticket | Resolution | Summary | Owner | Reporter |
|---|---|---|---|---|
| #1561 | invalid | smartctl no longer detects /dev/sdb and /dev/sdd temperatures | ||
| Description |
Hello. I used to see all the temperatures of my hard disks, but I changed my disk / and since then, smartctl no longer sees the temperatures of my /dev/sdb and /dev/sdd. I am under Manjaro Linux in AMD64. Can anybody help me ? Thanks Ignace. |
|||
| #1581 | invalid | smartctl never completes when all information is requested from a 4K Native WD drive over USB | ||
| Description |
When the drive is configured 512e, there is no problem. When the drive is configured 4K Native, running "smartctl --xall pd1" results in an infinite loading condition and the only way to stop it is to unplug the drive. This only happens over USB and works fine over a direct SATA connection. It's worth noting I have tested a lot of drives over USB and this is the only time I have seen this issue. The drive was originally 512e, but was changed to 4K Native using this tool: https://github.com/pig1800/WD4kConverter Disk model: WDC WD4005FZBX-00K5WB0 (WD Black 4 TB 3.5") USB docking station: Sabrent DS-UTC1 I believe the chipset on the docking station is the ASMedia ASM235CM. When the drive is unplugged, smartctl immediately returns the attached information (there are many errors). The LED activity light on the docking station blinks the whole time and never stops until it's powered off. My theory is that the the USB chip can't handle one of the commands you are sending. It's a bit odd it took a sector size change to expose the issue, though. |
|||
| #548 | fixed | smartctl mistakenly reports error where none is... | ||
| Description |
The offending line/output is: SMART Status command failed: scsi error medium or hardware error (serious) I noticed this odd behavior when I upgraded from smartmontools from 5.41 to 6.4 (automatically triggered in Debian when diet-upgrading from Wheezy to Jessie). I had several SATA drives (SSD and rotational) that I had tested when connected via SATA and they tested fine, in both 5.41 and in 6.4. When connected to a supported USB FA-GoFlex Desk device, it worked fine under 5.41. After upgrading to 6.4, I saw this erroneous output : smartctl 6.4 2014-10-07 r4002 [armv5tel-linux-3.14.0-kirkwood-tld-1] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD10EFRX-68FYTN0
Serial Number: WD-WCC4J4YR09FP
LU WWN Device Id: 5 0014ee 2b64e6f60
Firmware Version: 82.00A82
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sat May 9 16:52:44 2015 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status command failed: scsi error medium or hardware error (serious)
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (13620) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 155) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 253 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 100 253 021 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 3
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 0
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 4
194 Temperature_Celsius 0x0022 114 114 000 Old_age Always - 29
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 0 -
# 2 Short offline Completed without error 00% 0 -
# 3 Short offline Completed without error 00% 0 -
# 4 Short offline Completed without error 00% 0 -
# 5 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Again, this has been replicated w/ known good drives. Downgrading to 5.41 mitigates the error. |
|||
