Custom Query (1455 matches)
Results (136 - 138 of 1455)
| Ticket | Resolution | Summary | Owner | Reporter |
|---|---|---|---|---|
| #1713 | fixed | New database entry: ADATA SU630 | ||
| Description |
This is a 1TB USB SSD from ADATA. It has an Unknown USB bridge [0x125f:0xa88a (0x9301)] that uses -d sat I ran the short test: smartctl pre-7.4 2023-03-21 r5470 [aarch64-linux-6.1.10-v8+] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ADATA SU630
Serial Number: 2K2020057758
LU WWN Device Id: 0 000000 000000000
Firmware Version: S1127B0
User Capacity: 960,197,124,096 bytes [960 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available, deterministic, zeroed
Device is: Not in smartctl database 7.3/5440
ATA Version is: ACS-2 T13/2015-D revision 3
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Apr 6 05:12:57 2023 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Unavailable
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x11) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0
5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0
9 Power_On_Hours -O--CK 100 100 050 - 19328
12 Power_Cycle_Count -O--CK 100 100 050 - 71
160 Unknown_Attribute -O--CK 100 100 050 - 0
161 Unknown_Attribute PO--CK 100 100 050 - 100
163 Unknown_Attribute -O--CK 100 100 050 - 187
164 Unknown_Attribute -O--CK 100 100 050 - 134919
165 Unknown_Attribute -O--CK 100 100 050 - 318
166 Unknown_Attribute -O--CK 100 100 050 - 16
167 Unknown_Attribute -O--CK 100 100 050 - 76
168 Unknown_Attribute -O--CK 100 100 050 - 5050
169 Unknown_Attribute -O--CK 100 100 050 - 99
175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0
176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 0
177 Wear_Leveling_Count -O--CK 100 100 050 - 0
178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 0
181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0
182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0
192 Power-Off_Retract_Count -O--CK 100 100 050 - 66
194 Temperature_Celsius -O---K 100 100 050 - 41
195 Hardware_ECC_Recovered -O--CK 100 100 050 - 0
196 Reallocated_Event_Count -O--CK 100 100 050 - 0
197 Current_Pending_Sector -O--CK 100 100 050 - 0
198 Offline_Uncorrectable -O--CK 100 100 050 - 0
199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 1
232 Available_Reservd_Space -O--CK 100 100 050 - 100
241 Total_LBAs_Written ----CK 100 100 050 - 310222
242 Total_LBAs_Read ----CK 100 100 050 - 58142
245 Unknown_Attribute -O--CK 100 100 050 - 1021460
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xde GPL VS 8 Device vendor specific log
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 42 (device log contains only the most recent 4 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 42 [1] log entry is empty
Error 41 [0] log entry is empty
Error 40 [3] log entry is empty
Error 39 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 00 00 00 00 00 00 00 00 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d1 01 01 00 00 4f 00 c2 01 00 00 00:00:00.000 SMART READ ATTRIBUTE THRESHOLDS [OBS-4]
2f 00 00 01 01 00 00 00 00 00 03 00 00 00:00:00.000 READ LOG EXT
2f 00 00 01 01 00 00 00 00 00 00 00 00 00:00:00.000 READ LOG EXT
b0 00 d5 01 01 00 00 4f 00 c2 00 00 00 00:00:00.000 SMART READ LOG
b0 00 da 00 00 00 00 4f 00 c2 00 00 00 00:00:00.000 SMART RETURN STATUS
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 19328 -
Selective Self-tests/Logging not supported
SCT Commands not supported
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 71 --- Lifetime Power-On Resets
0x01 0x010 4 19328 --- Power-on Hours
0x01 0x018 6 3150847013 --- Logical Sectors Written
0x01 0x020 6 295279703 --- Number of Write Commands
0x01 0x028 6 3810455378 --- Logical Sectors Read
0x01 0x030 6 39980173 --- Number of Read Commands
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
0x07 0x008 1 1 --- Percentage Used Endurance Indicator
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x000a 4 19 Device-to-host register FISes sent due to a COMRESET
FARM log (GP Log 0xA6) not supported for non-Seagate drives
|
|||
| #1255 | fixed | smartctl reports drive not in smartctl database (HITACHI HUA721075KLA330) | ||
| Description |
SYMPTOM: smartctl incorrectly reports drive not is smartctl database { "Hitachi Ultrastar A7K1000", // tested with
// HUA721010KLA330 44X2459 42C0424IBM/GKAOAB4A
"(**Hitachi** )?HUA7210(50|75|10)KLA330.*",
"", "", ""
},
=== START OF INFORMATION SECTION ===
Device Model: HITACHI HUA721075KLA330
Serial Number: P8H91GWF
LU WWN Device Id: 5 000cca 215d23466
Firmware Version: GK8OA90A
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Size: 512 bytes logical/physical
**Device is: Not in smartctl database [for details use: -P showall]**
ATA Version is: ATA/ATAPI-7 T13/1532D revision 1
Local Time is: Sun Oct 27 08:50:18 2019 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
SYMPTOM: smartctl now correctly reports drive in smartctl database CAUSE: letter case mismatch on drive "Device Model:" { "Hitachi Ultrastar A7K1000", // tested with
// HUA721010KLA330 44X2459 42C0424IBM/GKAOAB4A
"(**HITACHI** )?HUA7210(50|75|10)KLA330.*",
"", "", ""
},
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Ultrastar A7K1000
Device Model: HITACHI HUA721075KLA330
Serial Number: P8H91GWF
LU WWN Device Id: 5 000cca 215d23466
Firmware Version: GK8OA90A
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Size: 512 bytes logical/physical
**Device is: In smartctl database [for details use: -P show]**
ATA Version is: ATA/ATAPI-7 T13/1532D revision 1
Local Time is: Sun Oct 27 07:47:20 2019 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
|
|||
| #1161 | duplicate | /dev/sda: Unknown USB bridge [0x152d:0x0578 (0x3101)] | ||
| Description |
Hi dear team, I am using one HC1 SBC board (octa armhf CPU 32 bits) from hardkernel with one 250 GB SSD drive connected on internal USB3 to SATA. It seems supported on Linux OS 4.18, because i can access on the device. It seems also possible to use LVM without issues in first analyse. But after creating around 120 logical partition (LV), i try to use smartmontools to extract statistics on the SSD. When i launch following command :
i have : Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org /dev/sda: Unknown USB bridge [0x152d:0x0578 (0x3101)] Please specify device type with the -d option. Current Linux kernel : root@srv-hc1-110:~# uname -a Linux srv-hc1-110 4.18.0-0.bpo.3-armmp-lpae #1 SMP Debian 4.18.20-2~bpo9+1 (2018-12-08) armv7l GNU/Linux root@srv-hc1-110:~# dpkg -l |grep smartmon ii smartmontools 6.5+svn4324-1 armhf control and monitor storage systems using S.M.A.R.T. Thanks in advance for your help Best regards |
|||
Note:
See TracQuery
for help on using queries.
