Custom Query (1552 matches)
Results (4 - 6 of 1552)
| Ticket | Resolution | Summary | Owner | Reporter |
|---|---|---|---|---|
| #1501 | invalid | Buffer I/O error logical block async page read (TOSHIBA MQ01ABD100) | ||
| Description |
Hi!I have Debian 11 64 bit installed on my machine. When I booted my machine today,I got the errors below during boot.Please find the output of the smartctl command below # smartctl -a /dev/sda
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-7-amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: 87PSPGCKT
LU WWN Device Id: 5 000039 7f2f0a12f
Firmware Version: AX1R4C
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Jun 12 19:55:38 2021 EAT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x86) Offline data collection activity
was aborted by the device with a fatal error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 199) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0027 100 100 050 Pre-fail Always - 0
3 Spin_Up_Time 0x0023 100 100 002 Pre-fail Always - 1762
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 3079
5 Reallocated_Sector_Ct 0x0033 099 099 010 Pre-fail Always - 320
7 Seek_Error_Rate 0x002f 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 058 058 000 Old_age Always - 17022
10 Spin_Retry_Count 0x0033 161 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2919
183 Runtime_Bad_Block 0x0032 100 100 001 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
185 Unknown_Attribute 0x0032 100 100 001 Old_age Always - 65535
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 1653
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 001 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 067 052 040 Old_age Always - 33 (Min/Max 28/42)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 213
192 Power-Off_Retract_Count 0x0022 100 100 000 Old_age Always - 5308497
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 5737
194 Temperature_Celsius 0x0022 067 052 040 Old_age Always - 33 (Min/Max 28/42)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 36
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 1653 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1653 occurred at disk power-on lifetime: 17011 hours (708 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 d0 06 f6 7f 40 Error: UNC at LBA = 0x007ff606 = 8386054
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 f8 d8 86 f6 7f 40 00 01:02:19.290 READ FPDMA QUEUED
60 08 d0 06 f6 7f 40 00 01:02:19.290 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 01:02:19.282 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 01:02:19.281 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 01:02:19.281 SET FEATURES [Set transfer mode]
Error 1652 occurred at disk power-on lifetime: 17011 hours (708 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 28 06 f6 7f 40 Error: UNC at LBA = 0x007ff606 = 8386054
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 f8 30 86 f6 7f 40 00 01:02:19.070 READ FPDMA QUEUED
60 08 28 06 f6 7f 40 00 01:02:19.070 READ FPDMA QUEUED
ef 10 03 00 00 00 a0 00 01:02:19.058 SET FEATURES [Enable SATA feature]
ef 10 02 00 00 00 a0 00 01:02:19.046 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 01:02:19.045 IDENTIFY DEVICE
Error 1651 occurred at disk power-on lifetime: 17011 hours (708 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 f8 06 f6 7f 40 Error: UNC at LBA = 0x007ff606 = 8386054
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 f8 00 86 f6 7f 40 00 01:02:18.597 READ FPDMA QUEUED
60 78 f8 06 f6 7f 40 00 01:02:18.597 READ FPDMA QUEUED
60 30 b8 c6 f5 7f 40 00 01:02:18.597 READ FPDMA QUEUED
60 10 b0 a6 f5 7f 40 00 01:02:18.597 READ FPDMA QUEUED
60 08 a8 8e f5 7f 40 00 01:02:18.597 READ FPDMA QUEUED
Error 1650 occurred at disk power-on lifetime: 17011 hours (708 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 08 06 f6 7f 40 Error: UNC at LBA = 0x007ff606 = 8386054
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 20 50 1e a6 94 40 00 01:02:04.069 READ FPDMA QUEUED
60 02 08 06 f6 7f 40 00 01:02:04.060 READ FPDMA QUEUED
60 02 18 0c f6 7f 40 00 01:02:04.027 READ FPDMA QUEUED
60 00 10 1e 89 95 40 00 01:02:04.027 READ FPDMA QUEUED
60 60 08 1e f6 7f 40 00 01:02:04.027 READ FPDMA QUEUED
Error 1649 occurred at disk power-on lifetime: 17011 hours (708 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 e0 06 f6 7f 40 Error: UNC at LBA = 0x007ff606 = 8386054
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 48 1e 89 95 40 00 01:02:03.896 READ FPDMA QUEUED
60 02 00 0c f6 7f 40 00 01:02:03.872 READ FPDMA QUEUED
60 02 f0 0a f6 7f 40 00 01:02:03.872 READ FPDMA QUEUED
60 02 e8 08 f6 7f 40 00 01:02:03.872 READ FPDMA QUEUED
60 02 e0 06 f6 7f 40 00 01:02:03.872 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 17008 209712646
# 2 Short offline Completed: read failure 90% 17008 209712646
# 3 Short offline Completed without error 00% 6747 -
# 4 Short offline Completed without error 00% 6747 -
# 5 Short offline Completed without error 00% 6747 -
# 6 Extended offline Aborted by host 90% 6747 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Output of dmesg from linux is as below # dmesg
[ 8431.341307] sd 0:0:0:0: [sda] tag#13 Sense Key : Medium Error [current]
[ 8431.341316] sd 0:0:0:0: [sda] tag#13 Add. Sense: Unrecovered read error - auto reallocate failed
[ 8431.341327] sd 0:0:0:0: [sda] tag#13 CDB: Read(10) 28 00 0c 7f f6 06 00 00 08 00
[ 8431.341340] blk_update_request: I/O error, dev sda, sector 209712646 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 8431.341358] Buffer I/O error on dev sda6, logical block 17, async page read
[ 8431.341415] ata1: EH complete
[ 8432.438648] ata1.00: exception Emask 0x0 SAct 0x8000000 SErr 0x40000 action 0x0
[ 8432.438653] ata1.00: irq_stat 0x40000008
[ 8432.438656] ata1: SError: { CommWake }
[ 8432.438659] ata1.00: failed command: READ FPDMA QUEUED
[ 8432.438664] ata1.00: cmd 60/08:d8:00:f6:7f/00:00:0c:00:00/40 tag 27 ncq dma 4096 in
res 41/40:00:06:f6:7f/00:00:0c:00:00/40 Emask 0x409 (media error) <F>
[ 8432.438666] ata1.00: status: { DRDY ERR }
[ 8432.438668] ata1.00: error: { UNC }
[ 8432.441244] ata1.00: configured for UDMA/100
[ 8432.441258] sd 0:0:0:0: [sda] tag#27 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE cmd_age=0s
[ 8432.441260] sd 0:0:0:0: [sda] tag#27 Sense Key : Medium Error [current]
[ 8432.441262] sd 0:0:0:0: [sda] tag#27 Add. Sense: Unrecovered read error - auto reallocate failed
[ 8432.441264] sd 0:0:0:0: [sda] tag#27 CDB: Read(10) 28 00 0c 7f f6 00 00 00 08 00
What do these errors mean and how can I resolve them.Seems there is a disk I/O error and I hope I dont have to replace the disk. /dev/sda6 is my /home partition and I have manged to boot my OS and reach the gnome desktop and somehow I am able to work normally but the disk I/O issues concern me. Please help |
|||
| #1229 | fixed | Transcend TS256GMTS430S | ||
| Description |
I have a Transcend TS256GMTS430S, which is an M.2 2242 SATA SSD. This drive is not yet supported in the smartmontools drive database. I will attach the output of "smartctl -x" to this ticket. From what I can determine through testing and research, the SMART data for this drive is the same as for other Transcend SSDs (e.g., see ticket #869 - https://www.smartmontools.org/ticket/869). I found some datasheets on the Internet that show that the SMART attributes are consistent across the various Transcend SSDs. I did locate a Transcend datasheet for the S400 SSD series as well (of which I'm guessing the S430 is a member of) - see http://transcend-info.com/products/images/modelpic/645/TSXGMTS400_V1.9%20DATASHEET.pdf - the SMART attributes are provided on page 13 of this PDF. |
|||
| #1389 | fixed | Kingston RBU-SNSx180S3 series SSDs (e.g., RBUSNS4180S3256GJ) | ||
| Description |
I have a Kingston RBUSNS4180S3256GJ SSD, which is an m.2 SATA SSD Kingston provides to system builders (see https://media.kingston.com/pdfs/emmc/MKF-815_design-in_SSD_lr.pdf). This SSD appears to use a Phison controller like many other Kingston SSDs, as the SMART attributes correctly match (plus some vendors that are selling MKF-815 SSDs list them as having a Phison controller). I verified several SMART attributes as well and they appear correct (e.g., read Lifetime_Reads_GiB, Temperature_Celcius, etc.) This change to drivedb.h appears to properly enable support for this drive (and likely this family): --- smartmontools-7.1/drivedb.h 2019-12-28 13:40:37.000000000 -0800
+++ smartmontools-7.1-new/drivedb.h 2020-10-25 10:50:30.291147928 -0700
@@ -673,6 +673,8 @@
"GOODRAM IRIDIUM PRO|" // tested with GOODRAM IRIDIUM PRO/SAFM01.5
"IR-SSDPR-S25A-(120|240|480|960)|" // Goodram IRIDM, tested with IR-SSDPR-S25A-120/SBFM91.3,
// IR-SSDPR-S25A-240/SBFM91.2
+ "KINGSTON RBUSNS(4|8)180S3(32|64|128|256|512)GJ|" // Kingston RBU-SNSx180S3 series, tested
+ // with KINGSTON RBUSNS4180S3256GJ
"KINGSTON SEDC400S37(400|480|800|960|1600|1800)G|" // DC400, tested with
// KINGSTON SEDC400S37480G/SAFM02.[GH], KINGSTON SEDC400S37960G/SAFM32.I
"KINGSTON SEDC(450R|500[MR])(480|960|1920|3840)G|" // DC450R, DC500M/R, tested with
I've attached the output of "smartctl -x" for this drive to this ticket as well. |
|||
Note:
See TracQuery
for help on using queries.
