Custom Query (1564 matches)

Hi, I've a disk that is not in the smart database:

Device Model:     Crucial_CT960M500SSD1
Serial Number:    14010960553B
LU WWN Device Id: 5 00a075 10960553b
Firmware Version: MU03
User Capacity:    960 197 124 096 bytes [960 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
Device is:        Not in smartctl database [for details use: -P showall]

Looking for information, I found #326 and referenced commits 3925 and 3926 that suggests me that I should be just needed to add the reference of my disk in smartctl database, hence this bug report. Here is the current report of smartctl (with smartmontools 6.3+svn4002 as in the Debian package):

Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate     0x002f   100   100   000    Pre-fail  Always       -       0
5 Reallocated_Sector_Ct   0x0033   100   100   000    Pre-fail  Always       -       0
9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       14138
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       24
171 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
172 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
173 Unknown_Attribute       0x0032   094   094   000    Old_age   Always       -       204
174 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       8
180 Unused_Rsvd_Blk_Cnt_Tot 0x0033   000   000   000    Pre-fail  Always       -       16523
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   000    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
194 Temperature_Celsius     0x0022   061   050   000    Old_age   Always       -       39 (Min/Max 0/50)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       16
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   100   100   000    Old_age   Always       -       0
202 Unknown_SSD_Attribute   0x0031   094   094   000    Pre-fail  Offline      -       6
206 Unknown_SSD_Attribute   0x000e   100   100   000    Old_age   Always       -       0
210 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
246 Unknown_Attribute       0x0032   100   100   ---    Old_age   Always       -       14853124027
247 Unknown_Attribute       0x0032   100   100   ---    Old_age   Always       -       696996831
248 Unknown_Attribute       0x0032   100   100   ---    Old_age   Always       -       3912597374

The current drivedb.h does not seem to list my disk for now (I did not compile and test the last svn commit, I just looked at the sources) : trunk/smartmontools/drivedb.h: [...]

    "Crucial_CT(120|240|480)M500SSD[13]", // Marvell 88SS9187 BLD2, tested with Crucial_CT120M500SSD3/MU02,
    // Crucial_CT120M500SSD1/MU02, Crucial_CT240M500SSD1/MU03, Crucial_CT480M500SSD1/MU03

[...]

Regards,

Vincent

T10's SPC-4 specifies the GLTSD bit in section 7.5.10 Control mode page as:

--- A global logging target save disable (GLTSD) bit set to zero specifies that the logical unit implicitly saves, at vendor specific intervals, each log parameter in which the TSD bit (see 7.3) is set to zero. A GLTSD bit set to one specifies that the logical unit shall not implicitly save any log parameters. ---

I have verified the functionality of the smartctl -S [on/off] /dev/sgX command on a SAS drive and believe the output is incorrect.

When you use -S on, you are enabling Autosaving of logs (set GLTSD bit to 0) but the printout says you are setting the GLTSD bit. This printout is incorrect. When you use -S off you are disabling Autosaving of logs (set GLTSD bit to 1) but the printout says you are clearing the GLTSD bit. This printout is incorrect.

(See attached picture)

On the bright side, I have verified that the command does correct set/clear the bit in the Control mode page 0Ah .

https://www.smartmontools.org/wiki/Supported_USB-Devices

hi there,

i would like to report a missing enclosure ​http://www.inxtron.com/desktop-hard-drive-enclosures/sk-3500-super-s

you just have written the newer s3 in your list. and: something strange on mac os x.9 & drivedx:

sometimes it was displayed as smart compatible.

but i did have some problems on slow finder, so trashed the smartap by inxtron as they wrote "just beyond 10.6.8"

and after them i installed new ​https://github.com/kasbert/OS-X-SAT-SMART-Driver. every versions of them after another, but the missing WDgreens did not come back

so i installed version 8 but rrom drivedx-site

nothing changed

maybe you have an idea

sincerly