smartctl version 5.0-36 Copyright (C) 2002 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: Maxtor 98196H8 Serial Number: V80HV6NC Firmware Version: ZAH814Y0 ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 0 SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Off-line data collection status: (0x00) Offline data collection activity was never started. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete off-line data collection: ( 30) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Automatic timer ON/OFF support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000a 253 252 000 Old_age - 26 3 Spin_Up_Time 0x0027 208 206 063 Pre-fail - 11285 4 Start_Stop_Count 0x0032 253 253 000 Old_age - 62 5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail - 0 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail - 0 7 Seek_Error_Rate 0x000a 253 252 000 Old_age - 0 8 Seek_Time_Performance 0x0027 249 244 187 Pre-fail - 50271 9 Power_On_Hours 0x0032 236 236 000 Old_age - 32671 10 Spin_Retry_Count 0x002b 253 252 223 Pre-fail - 0 11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail - 0 12 Power_Cycle_Count 0x0032 253 253 000 Old_age - 67 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age - 0 197 Current_Pending_Sector 0x0008 253 253 000 Old_age - 0 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age - 0 199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age - 0 200 Unknown_Attribute 0x000a 253 252 000 Old_age - 0 201 Unknown_Attribute 0x000a 253 252 000 Old_age - 1 202 Unknown_Attribute 0x000a 253 252 000 Old_age - 0 203 Unknown_Attribute 0x000b 253 252 180 Pre-fail - 2 204 Unknown_Attribute 0x000a 253 252 000 Old_age - 0 205 Unknown_Attribute 0x000a 253 252 000 Old_age - 0 207 Unknown_Attribute 0x002a 253 252 000 Old_age - 0 208 Unknown_Attribute 0x002a 253 252 000 Old_age - 0 209 Unknown_Attribute 0x0024 253 253 000 Old_age - 0 96 Unknown_Attribute 0x0004 253 253 000 Old_age - 0 97 Unknown_Attribute 0x0004 253 253 000 Old_age - 0 98 Unknown_Attribute 0x0004 253 253 000 Old_age - 0 99 Unknown_Attribute 0x0004 253 253 000 Old_age - 0 100 Unknown_Attribute 0x0004 253 253 000 Old_age - 0 101 Unknown_Attribute 0x0004 253 253 000 Old_age - 0 SMART Error Log Version: 1 ATA Error Count: 3 DCR = Device Control Register FR = Features Register SC = Sector Count Register SN = Sector Number Register CL = Cylinder Low Register CH = Cylinder High Register D/H = Device/Head Register CR = Content written to Command Register ER = Error register STA = Status register Timestamp is seconds since the previous disk power-on. Note: timestamp "wraps" after 2^32 msec = 49.710 days. Error 1 occurred at disk power-on lifetime: 0 hours When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER:04 SC:40 SN:42 CL:97 CH:23 D/H:00 ST:51 Sequence of commands leading to the command that caused the error were: DCR FR SC SN CL CH D/H CR Timestamp 00 fe 00 00 00 00 00 ef 137.440 00 d9 00 00 4f c2 00 b0 137.328 00 da 00 00 4f c2 00 b0 137.232 00 d8 00 00 4f c2 00 b0 137.152 00 db 00 00 4f c2 00 b0 136.976 Error 2 occurred at disk power-on lifetime: 0 hours When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER:04 SC:40 SN:40 CL:97 CH:23 D/H:00 ST:51 Sequence of commands leading to the command that caused the error were: DCR FR SC SN CL CH D/H CR Timestamp 00 fe 00 00 00 00 00 ef 342.432 00 e4 00 00 00 00 00 c3 342.368 00 d0 00 00 0a 00 00 c3 342.368 00 fe 00 00 00 00 00 ef 342.304 00 3d 00 00 00 00 00 c3 342.256 Error 3 occurred at disk power-on lifetime: 0 hours When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER:04 SC:40 SN:40 CL:97 CH:03 D/H:00 ST:51 Sequence of commands leading to the command that caused the error were: DCR FR SC SN CL CH D/H CR Timestamp 00 fe 00 00 00 00 00 ef 342.304 00 3d 00 00 00 00 00 c3 342.256 00 e4 00 00 00 00 00 c3 342.192 00 3d 00 00 00 00 00 c3 342.192 00 00 01 01 00 00 00 ec 342.144 SMART Self-test log, version number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short off-line Completed 00% 5255