| 1 | smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.13.9-200.fc26.x86_64] (local build) |
|---|
| 2 | Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org |
|---|
| 3 | |
|---|
| 4 | === START OF INFORMATION SECTION === |
|---|
| 5 | Device Model: TOSHIBA MQ04UBF100 |
|---|
| 6 | Firmware Version: JU000U |
|---|
| 7 | User Capacity: 1,000,204,886,016 bytes [1.00 TB] |
|---|
| 8 | Sector Sizes: 512 bytes logical, 4096 bytes physical |
|---|
| 9 | Rotation Rate: 5400 rpm |
|---|
| 10 | Form Factor: 2.5 inches |
|---|
| 11 | Device is: Not in smartctl database [for details use: -P showall] |
|---|
| 12 | ATA Version is: ACS-3 T13/2161-D revision 5 |
|---|
| 13 | SATA Version is: SATA >3.2 (0x1ff), 3.0 Gb/s (current: 3.0 Gb/s) |
|---|
| 14 | Local Time is: Mon Oct 30 18:37:15 2017 CET |
|---|
| 15 | SMART support is: Available - device has SMART capability. |
|---|
| 16 | SMART support is: Enabled |
|---|
| 17 | AAM feature is: Unavailable |
|---|
| 18 | APM level is: 128 (minimum power consumption without standby) |
|---|
| 19 | Rd look-ahead is: Enabled |
|---|
| 20 | Write cache is: Enabled |
|---|
| 21 | ATA Security is: Disabled, NOT FROZEN [SEC1] |
|---|
| 22 | Wt Cache Reorder: Unknown |
|---|
| 23 | |
|---|
| 24 | === START OF READ SMART DATA SECTION === |
|---|
| 25 | SMART Status not supported: Incomplete response, ATA output registers missing |
|---|
| 26 | SMART overall-health self-assessment test result: PASSED |
|---|
| 27 | Warning: This result is based on an Attribute check. |
|---|
| 28 | |
|---|
| 29 | General SMART Values: |
|---|
| 30 | Offline data collection status: (0x00) Offline data collection activity |
|---|
| 31 | was never started. |
|---|
| 32 | Auto Offline Data Collection: Disabled. |
|---|
| 33 | Self-test execution status: ( 0) The previous self-test routine completed |
|---|
| 34 | without error or no self-test has ever |
|---|
| 35 | been run. |
|---|
| 36 | Total time to complete Offline |
|---|
| 37 | data collection: ( 120) seconds. |
|---|
| 38 | Offline data collection |
|---|
| 39 | capabilities: (0x5b) SMART execute Offline immediate. |
|---|
| 40 | Auto Offline data collection on/off support. |
|---|
| 41 | Suspend Offline collection upon new |
|---|
| 42 | command. |
|---|
| 43 | Offline surface scan supported. |
|---|
| 44 | Self-test supported. |
|---|
| 45 | No Conveyance Self-test supported. |
|---|
| 46 | Selective Self-test supported. |
|---|
| 47 | SMART capabilities: (0x0003) Saves SMART data before entering |
|---|
| 48 | power-saving mode. |
|---|
| 49 | Supports SMART auto save timer. |
|---|
| 50 | Error logging capability: (0x01) Error logging supported. |
|---|
| 51 | General Purpose Logging supported. |
|---|
| 52 | Short self-test routine |
|---|
| 53 | recommended polling time: ( 2) minutes. |
|---|
| 54 | Extended self-test routine |
|---|
| 55 | recommended polling time: ( 176) minutes. |
|---|
| 56 | SCT capabilities: (0x003d) SCT Status supported. |
|---|
| 57 | SCT Error Recovery Control supported. |
|---|
| 58 | SCT Feature Control supported. |
|---|
| 59 | SCT Data Table supported. |
|---|
| 60 | |
|---|
| 61 | SMART Attributes Data Structure revision number: 16 |
|---|
| 62 | Vendor Specific SMART Attributes with Thresholds: |
|---|
| 63 | ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE |
|---|
| 64 | 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 |
|---|
| 65 | 2 Throughput_Performance P-S--- 100 100 050 - 0 |
|---|
| 66 | 3 Spin_Up_Time POS--K 100 100 001 - 2994 |
|---|
| 67 | 4 Start_Stop_Count -O--CK 100 100 000 - 8 |
|---|
| 68 | 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 0 |
|---|
| 69 | 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 |
|---|
| 70 | 8 Seek_Time_Performance P-S--- 100 100 050 - 0 |
|---|
| 71 | 9 Power_On_Hours -O--CK 100 100 000 - 0 |
|---|
| 72 | 10 Spin_Retry_Count PO--CK 100 100 030 - 0 |
|---|
| 73 | 12 Power_Cycle_Count -O--CK 100 100 000 - 5 |
|---|
| 74 | 191 G-Sense_Error_Rate -O--CK 100 100 000 - 3 |
|---|
| 75 | 192 Power-Off_Retract_Count -O--CK 100 100 000 - 0 |
|---|
| 76 | 193 Load_Cycle_Count -O--CK 100 100 000 - 11 |
|---|
| 77 | 194 Temperature_Celsius -O---K 100 100 000 - 25 (Min/Max 16/28) |
|---|
| 78 | 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 |
|---|
| 79 | 197 Current_Pending_Sector -O--CK 100 100 000 - 0 |
|---|
| 80 | 198 Offline_Uncorrectable ----CK 100 100 000 - 0 |
|---|
| 81 | 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 |
|---|
| 82 | 220 Disk_Shift -O---- 100 100 000 - 0 |
|---|
| 83 | 222 Loaded_Hours -O--CK 100 100 000 - 0 |
|---|
| 84 | 223 Load_Retry_Count -O--CK 100 100 000 - 0 |
|---|
| 85 | 224 Load_Friction -O---K 100 100 000 - 0 |
|---|
| 86 | 226 Load-in_Time -OS--K 100 100 000 - 270 |
|---|
| 87 | 240 Head_Flying_Hours P----- 100 100 001 - 0 |
|---|
| 88 | ||||||_ K auto-keep |
|---|
| 89 | |||||__ C event count |
|---|
| 90 | ||||___ R error rate |
|---|
| 91 | |||____ S speed/performance |
|---|
| 92 | ||_____ O updated online |
|---|
| 93 | |______ P prefailure warning |
|---|
| 94 | |
|---|
| 95 | General Purpose Log Directory Version 1 |
|---|
| 96 | SMART Log Directory Version 1 [multi-sector log support] |
|---|
| 97 | Address Access R/W Size Description |
|---|
| 98 | 0x00 GPL,SL R/O 1 Log Directory |
|---|
| 99 | 0x01 SL R/O 1 Summary SMART error log |
|---|
| 100 | 0x02 SL R/O 51 Comprehensive SMART error log |
|---|
| 101 | 0x03 GPL R/O 64 Ext. Comprehensive SMART error log |
|---|
| 102 | 0x04 GPL,SL R/O 8 Device Statistics log |
|---|
| 103 | 0x06 SL R/O 1 SMART self-test log |
|---|
| 104 | 0x07 GPL R/O 1 Extended self-test log |
|---|
| 105 | 0x09 SL R/W 1 Selective self-test log |
|---|
| 106 | 0x0a GPL R/W 2 Device Statistics Notification |
|---|
| 107 | 0x10 GPL R/O 1 SATA NCQ Queued Error log |
|---|
| 108 | 0x11 GPL R/O 1 SATA Phy Event Counters log |
|---|
| 109 | 0x24 GPL R/O 32768 Current Device Internal Status Data log |
|---|
| 110 | 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log |
|---|
| 111 | 0x80-0x9f GPL,SL R/W 16 Host vendor specific log |
|---|
| 112 | 0xa7 GPL VS 8 Device vendor specific log |
|---|
| 113 | 0xe0 GPL,SL R/W 1 SCT Command/Status |
|---|
| 114 | 0xe1 GPL,SL R/W 1 SCT Data Transfer |
|---|
| 115 | |
|---|
| 116 | SMART Extended Comprehensive Error Log Version: 1 (64 sectors) |
|---|
| 117 | No Errors Logged |
|---|
| 118 | |
|---|
| 119 | SMART Extended Self-test Log Version: 1 (1 sectors) |
|---|
| 120 | Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error |
|---|
| 121 | # 1 Short offline Completed without error 00% 0 - |
|---|
| 122 | |
|---|
| 123 | SMART Selective self-test log data structure revision number 1 |
|---|
| 124 | SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS |
|---|
| 125 | 1 0 0 Not_testing |
|---|
| 126 | 2 0 0 Not_testing |
|---|
| 127 | 3 0 0 Not_testing |
|---|
| 128 | 4 0 0 Not_testing |
|---|
| 129 | 5 0 0 Not_testing |
|---|
| 130 | Selective self-test flags (0x0): |
|---|
| 131 | After scanning selected spans, do NOT read-scan remainder of disk. |
|---|
| 132 | If Selective self-test is pending on power-up, resume after 0 minute delay. |
|---|
| 133 | |
|---|
| 134 | SCT Status Version: 3 |
|---|
| 135 | SCT Version (vendor specific): 1 (0x0001) |
|---|
| 136 | SCT Support Level: 1 |
|---|
| 137 | Device State: Active (0) |
|---|
| 138 | Current Temperature: 25 Celsius |
|---|
| 139 | Power Cycle Min/Max Temperature: 16/26 Celsius |
|---|
| 140 | Lifetime Min/Max Temperature: 16/28 Celsius |
|---|
| 141 | Under/Over Temperature Limit Count: 0/0 |
|---|
| 142 | |
|---|
| 143 | SCT Temperature History Version: 2 |
|---|
| 144 | Temperature Sampling Period: 1 minute |
|---|
| 145 | Temperature Logging Interval: 1 minute |
|---|
| 146 | Min/Max recommended Temperature: 0/60 Celsius |
|---|
| 147 | Min/Max Temperature Limit: 0/60 Celsius |
|---|
| 148 | Temperature History Size (Index): 478 (25) |
|---|
| 149 | |
|---|
| 150 | Index Estimated Time Temperature Celsius |
|---|
| 151 | 26 2017-10-30 10:40 ? - |
|---|
| 152 | ... ..(455 skipped). .. - |
|---|
| 153 | 4 2017-10-30 18:16 ? - |
|---|
| 154 | 5 2017-10-30 18:17 17 - |
|---|
| 155 | 6 2017-10-30 18:18 17 - |
|---|
| 156 | 7 2017-10-30 18:19 18 - |
|---|
| 157 | 8 2017-10-30 18:20 ? - |
|---|
| 158 | 9 2017-10-30 18:21 20 * |
|---|
| 159 | 10 2017-10-30 18:22 20 * |
|---|
| 160 | 11 2017-10-30 18:23 21 ** |
|---|
| 161 | 12 2017-10-30 18:24 21 ** |
|---|
| 162 | 13 2017-10-30 18:25 ? - |
|---|
| 163 | 14 2017-10-30 18:26 22 *** |
|---|
| 164 | 15 2017-10-30 18:27 22 *** |
|---|
| 165 | 16 2017-10-30 18:28 22 *** |
|---|
| 166 | 17 2017-10-30 18:29 ? - |
|---|
| 167 | 18 2017-10-30 18:30 23 **** |
|---|
| 168 | 19 2017-10-30 18:31 23 **** |
|---|
| 169 | 20 2017-10-30 18:32 24 ***** |
|---|
| 170 | 21 2017-10-30 18:33 26 ******* |
|---|
| 171 | 22 2017-10-30 18:34 26 ******* |
|---|
| 172 | 23 2017-10-30 18:35 25 ****** |
|---|
| 173 | 24 2017-10-30 18:36 25 ****** |
|---|
| 174 | 25 2017-10-30 18:37 ? - |
|---|
| 175 | |
|---|
| 176 | SMART WRITE LOG does not return COUNT and LBA_LOW register |
|---|
| 177 | SCT (Get) Error Recovery Control command failed |
|---|
| 178 | |
|---|
| 179 | Device Statistics (GP Log 0x04) |
|---|
| 180 | Page Offset Size Value Flags Description |
|---|
| 181 | 0x01 ===== = = === == General Statistics (rev 1) == |
|---|
| 182 | 0x01 0x008 4 5 --- Lifetime Power-On Resets |
|---|
| 183 | 0x01 0x010 4 0 --- Power-on Hours |
|---|
| 184 | 0x01 0x018 6 513609 --- Logical Sectors Written |
|---|
| 185 | 0x01 0x020 6 10058 --- Number of Write Commands |
|---|
| 186 | 0x01 0x028 6 711346 --- Logical Sectors Read |
|---|
| 187 | 0x01 0x030 6 5581 --- Number of Read Commands |
|---|
| 188 | 0x01 0x038 6 1847258 --- Date and Time TimeStamp |
|---|
| 189 | 0x02 ===== = = === == Free-Fall Statistics (rev 1) == |
|---|
| 190 | 0x02 0x010 4 3 --- Overlimit Shock Events |
|---|
| 191 | 0x03 ===== = = === == Rotating Media Statistics (rev 1) == |
|---|
| 192 | 0x03 0x008 4 0 --- Spindle Motor Power-on Hours |
|---|
| 193 | 0x03 0x010 4 0 --- Head Flying Hours |
|---|
| 194 | 0x03 0x018 4 12 --- Head Load Events |
|---|
| 195 | 0x03 0x020 4 0 -D- Number of Reallocated Logical Sectors |
|---|
| 196 | 0x03 0x028 4 0 --- Read Recovery Attempts |
|---|
| 197 | 0x03 0x030 4 0 --- Number of Mechanical Start Failures |
|---|
| 198 | 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors |
|---|
| 199 | 0x03 0x040 4 0 --- Number of High Priority Unload Events |
|---|
| 200 | 0x04 ===== = = === == General Errors Statistics (rev 1) == |
|---|
| 201 | 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors |
|---|
| 202 | 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion |
|---|
| 203 | 0x05 ===== = = === == Temperature Statistics (rev 1) == |
|---|
| 204 | 0x05 0x008 1 25 --- Current Temperature |
|---|
| 205 | 0x05 0x010 1 - N-- Average Short Term Temperature |
|---|
| 206 | 0x05 0x018 1 - N-- Average Long Term Temperature |
|---|
| 207 | 0x05 0x020 1 28 --- Highest Temperature |
|---|
| 208 | 0x05 0x028 1 16 --- Lowest Temperature |
|---|
| 209 | 0x05 0x030 1 - N-- Highest Average Short Term Temperature |
|---|
| 210 | 0x05 0x038 1 - N-- Lowest Average Short Term Temperature |
|---|
| 211 | 0x05 0x040 1 - N-- Highest Average Long Term Temperature |
|---|
| 212 | 0x05 0x048 1 - N-- Lowest Average Long Term Temperature |
|---|
| 213 | 0x05 0x050 4 0 --- Time in Over-Temperature |
|---|
| 214 | 0x05 0x058 1 60 --- Specified Maximum Operating Temperature |
|---|
| 215 | 0x05 0x060 4 0 --- Time in Under-Temperature |
|---|
| 216 | 0x05 0x068 1 0 --- Specified Minimum Operating Temperature |
|---|
| 217 | 0x06 ===== = = === == Transport Statistics (rev 1) == |
|---|
| 218 | 0x06 0x008 4 0 --- Number of Hardware Resets |
|---|
| 219 | 0x06 0x010 4 4 --- Number of ASR Events |
|---|
| 220 | 0x06 0x018 4 0 --- Number of Interface CRC Errors |
|---|
| 221 | 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |
|---|
| 222 | |||_ C monitored condition met |
|---|
| 223 | ||__ D supports DSN |
|---|
| 224 | |___ N normalized value |
|---|
| 225 | |
|---|
| 226 | SATA Phy Event Counters (GP Log 0x11) |
|---|
| 227 | ID Size Value Description |
|---|
| 228 | 0x0001 4 0 Command failed due to ICRC error |
|---|
| 229 | 0x0002 4 0 R_ERR response for data FIS |
|---|
| 230 | 0x0003 4 0 R_ERR response for device-to-host data FIS |
|---|
| 231 | 0x0004 4 0 R_ERR response for host-to-device data FIS |
|---|
| 232 | 0x0005 4 0 R_ERR response for non-data FIS |
|---|
| 233 | 0x0006 4 0 R_ERR response for device-to-host non-data FIS |
|---|
| 234 | 0x0007 4 0 R_ERR response for host-to-device non-data FIS |
|---|
| 235 | 0x0008 4 0 Device-to-host non-data FIS retries |
|---|
| 236 | 0x0009 4 1 Transition from drive PhyRdy to drive PhyNRdy |
|---|
| 237 | 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET |
|---|
| 238 | 0x000b 4 0 CRC errors within host-to-device FIS |
|---|
| 239 | 0x000d 4 0 Non-CRC errors within host-to-device FIS |
|---|
| 240 | 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC |
|---|
| 241 | 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC |
|---|
| 242 | 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC |
|---|
| 243 | 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC |
|---|
| 244 | |
|---|
