1 | smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.10.0-28-generic] (local build) |
---|
2 | Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org |
---|
3 | |
---|
4 | === START OF INFORMATION SECTION === |
---|
5 | Device Model: WDC WD4000FDYZ-27YA5B0 |
---|
6 | Serial Number: WD-WCC132156748 |
---|
7 | LU WWN Device Id: 5 0014ee 25f86430e |
---|
8 | Firmware Version: 01.01K06 |
---|
9 | User Capacity: 4,000,787,030,016 bytes [4.00 TB] |
---|
10 | Sector Size: 512 bytes logical/physical |
---|
11 | Rotation Rate: 7200 rpm |
---|
12 | Device is: Not in smartctl database [for details use: -P showall] |
---|
13 | ATA Version is: ATA8-ACS (minor revision not indicated) |
---|
14 | SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) |
---|
15 | Local Time is: Thu Jul 27 16:17:44 2017 PDT |
---|
16 | SMART support is: Available - device has SMART capability. |
---|
17 | SMART support is: Enabled |
---|
18 | AAM feature is: Unavailable |
---|
19 | APM level is: 254 (maximum performance) |
---|
20 | Rd look-ahead is: Enabled |
---|
21 | Write cache is: Enabled |
---|
22 | ATA Security is: Disabled, frozen [SEC2] |
---|
23 | Wt Cache Reorder: Enabled |
---|
24 | |
---|
25 | === START OF READ SMART DATA SECTION === |
---|
26 | SMART overall-health self-assessment test result: PASSED |
---|
27 | |
---|
28 | General SMART Values: |
---|
29 | Offline data collection status: (0x84) Offline data collection activity |
---|
30 | was suspended by an interrupting command from host. |
---|
31 | Auto Offline Data Collection: Enabled. |
---|
32 | Self-test execution status: ( 0) The previous self-test routine completed |
---|
33 | without error or no self-test has ever |
---|
34 | been run. |
---|
35 | Total time to complete Offline |
---|
36 | data collection: (47400) seconds. |
---|
37 | Offline data collection |
---|
38 | capabilities: (0x7b) SMART execute Offline immediate. |
---|
39 | Auto Offline data collection on/off support. |
---|
40 | Suspend Offline collection upon new |
---|
41 | command. |
---|
42 | Offline surface scan supported. |
---|
43 | Self-test supported. |
---|
44 | Conveyance Self-test supported. |
---|
45 | Selective Self-test supported. |
---|
46 | SMART capabilities: (0x0003) Saves SMART data before entering |
---|
47 | power-saving mode. |
---|
48 | Supports SMART auto save timer. |
---|
49 | Error logging capability: (0x01) Error logging supported. |
---|
50 | General Purpose Logging supported. |
---|
51 | Short self-test routine |
---|
52 | recommended polling time: ( 2) minutes. |
---|
53 | Extended self-test routine |
---|
54 | recommended polling time: ( 513) minutes. |
---|
55 | Conveyance self-test routine |
---|
56 | recommended polling time: ( 5) minutes. |
---|
57 | SCT capabilities: (0x70b9) SCT Status supported. |
---|
58 | SCT Error Recovery Control supported. |
---|
59 | SCT Feature Control supported. |
---|
60 | SCT Data Table supported. |
---|
61 | |
---|
62 | SMART Attributes Data Structure revision number: 16 |
---|
63 | Vendor Specific SMART Attributes with Thresholds: |
---|
64 | ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE |
---|
65 | 1 Raw_Read_Error_Rate POSR-K 200 196 051 - 0 |
---|
66 | 3 Spin_Up_Time POS--K 253 227 021 - 5541 |
---|
67 | 4 Start_Stop_Count -O--CK 100 100 000 - 160 |
---|
68 | 5 Reallocated_Sector_Ct PO--CK 198 198 140 - 85 |
---|
69 | 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 |
---|
70 | 9 Power_On_Hours -O--CK 068 068 000 - 23929 |
---|
71 | 10 Spin_Retry_Count -O--CK 100 100 000 - 0 |
---|
72 | 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 |
---|
73 | 12 Power_Cycle_Count -O--CK 100 100 000 - 148 |
---|
74 | 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 |
---|
75 | 192 Power-Off_Retract_Count -O--CK 200 200 000 - 123 |
---|
76 | 193 Load_Cycle_Count -O--CK 200 200 000 - 49 |
---|
77 | 194 Temperature_Celsius -O---K 108 098 000 - 44 |
---|
78 | 196 Reallocated_Event_Count -O--CK 190 190 000 - 10 |
---|
79 | 197 Current_Pending_Sector -O--CK 200 200 000 - 0 |
---|
80 | 198 Offline_Uncorrectable ----CK 200 200 000 - 0 |
---|
81 | 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 |
---|
82 | 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 |
---|
83 | ||||||_ K auto-keep |
---|
84 | |||||__ C event count |
---|
85 | ||||___ R error rate |
---|
86 | |||____ S speed/performance |
---|
87 | ||_____ O updated online |
---|
88 | |______ P prefailure warning |
---|
89 | |
---|
90 | General Purpose Log Directory Version 1 |
---|
91 | SMART Log Directory Version 1 [multi-sector log support] |
---|
92 | Address Access R/W Size Description |
---|
93 | 0x00 GPL,SL R/O 1 Log Directory |
---|
94 | 0x01 SL R/O 1 Summary SMART error log |
---|
95 | 0x02 SL R/O 5 Comprehensive SMART error log |
---|
96 | 0x03 GPL R/O 6 Ext. Comprehensive SMART error log |
---|
97 | 0x06 SL R/O 1 SMART self-test log |
---|
98 | 0x07 GPL R/O 1 Extended self-test log |
---|
99 | 0x08 GPL R/O 2 Power Conditions log |
---|
100 | 0x09 SL R/W 1 Selective self-test log |
---|
101 | 0x10 GPL R/O 1 SATA NCQ Queued Error log |
---|
102 | 0x11 GPL R/O 1 SATA Phy Event Counters log |
---|
103 | 0x24 GPL R/O 1 Current Device Internal Status Data log |
---|
104 | 0x80-0x9f GPL,SL R/W 16 Host vendor specific log |
---|
105 | 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log |
---|
106 | 0xa8-0xb1 GPL,SL VS 1 Device vendor specific log |
---|
107 | 0xb2 GPL VS 65535 Device vendor specific log |
---|
108 | 0xb2 SL VS 255 Device vendor specific log |
---|
109 | 0xb3-0xb7 GPL,SL VS 1 Device vendor specific log |
---|
110 | 0xbd GPL,SL VS 1 Device vendor specific log |
---|
111 | 0xc0 GPL,SL VS 1 Device vendor specific log |
---|
112 | 0xc1 GPL VS 24 Device vendor specific log |
---|
113 | 0xe0 GPL,SL R/W 1 SCT Command/Status |
---|
114 | 0xe1 GPL,SL R/W 1 SCT Data Transfer |
---|
115 | |
---|
116 | SMART Extended Comprehensive Error Log Version: 1 (6 sectors) |
---|
117 | Device Error Count: 151 (device log contains only the most recent 24 errors) |
---|
118 | CR = Command Register |
---|
119 | FEATR = Features Register |
---|
120 | COUNT = Count (was: Sector Count) Register |
---|
121 | LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 |
---|
122 | LH = LBA High (was: Cylinder High) Register ] LBA |
---|
123 | LM = LBA Mid (was: Cylinder Low) Register ] Register |
---|
124 | LL = LBA Low (was: Sector Number) Register ] |
---|
125 | DV = Device (was: Device/Head) Register |
---|
126 | DC = Device Control Register |
---|
127 | ER = Error register |
---|
128 | ST = Status register |
---|
129 | Powered_Up_Time is measured from power on, and printed as |
---|
130 | DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, |
---|
131 | SS=sec, and sss=millisec. It "wraps" after 49.710 days. |
---|
132 | |
---|
133 | Error 151 [6] occurred at disk power-on lifetime: 23084 hours (961 days + 20 hours) |
---|
134 | When the command that caused the error occurred, the device was active or idle. |
---|
135 | |
---|
136 | After command completion occurred, registers were: |
---|
137 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
138 | -- -- -- == -- == == == -- -- -- -- -- |
---|
139 | 40 -- 51 00 08 00 01 9e 04 0f 7a e0 00 Error: UNC 8 sectors at LBA = 0x19e040f7a = 6946033530 |
---|
140 | |
---|
141 | Commands leading to the command that caused the error were: |
---|
142 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
143 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
144 | 25 00 00 00 08 00 01 9e 04 0f 78 e0 0a 2d+09:42:59.972 READ DMA EXT |
---|
145 | 25 00 00 00 08 00 01 9e 04 0f 70 e0 0a 2d+09:42:59.972 READ DMA EXT |
---|
146 | 25 00 00 00 08 00 01 9e 04 0f 68 e0 0a 2d+09:42:59.972 READ DMA EXT |
---|
147 | 25 00 00 00 08 00 01 9e 04 0f 60 e0 0a 2d+09:42:59.972 READ DMA EXT |
---|
148 | 25 00 00 00 08 00 01 9e 04 0f 58 e0 0a 2d+09:42:59.972 READ DMA EXT |
---|
149 | |
---|
150 | Error 150 [5] occurred at disk power-on lifetime: 23084 hours (961 days + 20 hours) |
---|
151 | When the command that caused the error occurred, the device was active or idle. |
---|
152 | |
---|
153 | After command completion occurred, registers were: |
---|
154 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
155 | -- -- -- == -- == == == -- -- -- -- -- |
---|
156 | 40 -- 51 08 00 00 01 9e 04 0f 7a e0 00 Error: UNC 2048 sectors at LBA = 0x19e040f7a = 6946033530 |
---|
157 | |
---|
158 | Commands leading to the command that caused the error were: |
---|
159 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
160 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
161 | 25 00 00 08 00 00 01 9e 04 08 00 e0 0a 2d+09:42:56.533 READ DMA EXT |
---|
162 | 25 00 00 04 00 00 01 9e 04 04 00 e0 0a 2d+09:42:56.478 READ DMA EXT |
---|
163 | 25 00 00 04 00 00 01 9e 04 00 00 e0 0a 2d+09:42:56.472 READ DMA EXT |
---|
164 | 25 00 00 02 50 00 01 9e 03 fd b0 e0 0a 2d+09:42:56.469 READ DMA EXT |
---|
165 | 25 00 00 05 b0 00 01 9e 03 f8 00 e0 0a 2d+09:42:56.462 READ DMA EXT |
---|
166 | |
---|
167 | Error 149 [4] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) |
---|
168 | When the command that caused the error occurred, the device was active or idle. |
---|
169 | |
---|
170 | After command completion occurred, registers were: |
---|
171 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
172 | -- -- -- == -- == == == -- -- -- -- -- |
---|
173 | 40 -- 51 00 08 00 01 41 b5 ac 12 e0 00 Error: UNC 8 sectors at LBA = 0x141b5ac12 = 5397392402 |
---|
174 | |
---|
175 | Commands leading to the command that caused the error were: |
---|
176 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
177 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
178 | 25 00 00 00 08 00 01 41 b5 ac 10 e0 0a 2d+07:43:42.001 READ DMA EXT |
---|
179 | 25 00 00 00 08 00 01 41 b5 ac 08 e0 0a 2d+07:43:42.001 READ DMA EXT |
---|
180 | 25 00 00 00 08 00 01 41 b5 ac 00 e0 0a 2d+07:43:42.001 READ DMA EXT |
---|
181 | 25 00 00 00 08 00 01 41 b5 ab f8 e0 0a 2d+07:43:42.000 READ DMA EXT |
---|
182 | 25 00 00 00 08 00 01 41 b5 ab f0 e0 0a 2d+07:43:42.000 READ DMA EXT |
---|
183 | |
---|
184 | Error 148 [3] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) |
---|
185 | When the command that caused the error occurred, the device was active or idle. |
---|
186 | |
---|
187 | After command completion occurred, registers were: |
---|
188 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
189 | -- -- -- == -- == == == -- -- -- -- -- |
---|
190 | 40 -- 51 00 08 00 01 41 b5 a3 8a e0 00 Error: UNC 8 sectors at LBA = 0x141b5a38a = 5397390218 |
---|
191 | |
---|
192 | Commands leading to the command that caused the error were: |
---|
193 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
194 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
195 | 25 00 00 00 08 00 01 41 b5 a3 88 e0 0a 2d+07:43:40.148 READ DMA EXT |
---|
196 | 25 00 00 00 08 00 01 41 b5 a3 80 e0 0a 2d+07:43:40.148 READ DMA EXT |
---|
197 | 25 00 00 00 08 00 01 41 b5 a3 78 e0 0a 2d+07:43:40.148 READ DMA EXT |
---|
198 | 25 00 00 00 08 00 01 41 b5 a3 70 e0 0a 2d+07:43:40.148 READ DMA EXT |
---|
199 | 25 00 00 00 08 00 01 41 b5 a3 68 e0 0a 2d+07:43:40.148 READ DMA EXT |
---|
200 | |
---|
201 | Error 147 [2] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) |
---|
202 | When the command that caused the error occurred, the device was active or idle. |
---|
203 | |
---|
204 | After command completion occurred, registers were: |
---|
205 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
206 | -- -- -- == -- == == == -- -- -- -- -- |
---|
207 | 40 -- 51 00 08 00 01 41 b5 9b 02 e0 00 Error: UNC 8 sectors at LBA = 0x141b59b02 = 5397388034 |
---|
208 | |
---|
209 | Commands leading to the command that caused the error were: |
---|
210 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
211 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
212 | 25 00 00 00 08 00 01 41 b5 9b 00 e0 0a 2d+07:43:38.263 READ DMA EXT |
---|
213 | 25 00 00 00 08 00 01 41 b5 9a f8 e0 0a 2d+07:43:38.262 READ DMA EXT |
---|
214 | 25 00 00 00 08 00 01 41 b5 9a f0 e0 0a 2d+07:43:38.262 READ DMA EXT |
---|
215 | 25 00 00 00 08 00 01 41 b5 9a e8 e0 0a 2d+07:43:38.262 READ DMA EXT |
---|
216 | 25 00 00 00 08 00 01 41 b5 9a e0 e0 0a 2d+07:43:38.262 READ DMA EXT |
---|
217 | |
---|
218 | Error 146 [1] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) |
---|
219 | When the command that caused the error occurred, the device was active or idle. |
---|
220 | |
---|
221 | After command completion occurred, registers were: |
---|
222 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
223 | -- -- -- == -- == == == -- -- -- -- -- |
---|
224 | 40 -- 51 00 08 00 01 41 b5 92 79 e0 00 Error: UNC 8 sectors at LBA = 0x141b59279 = 5397385849 |
---|
225 | |
---|
226 | Commands leading to the command that caused the error were: |
---|
227 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
228 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
229 | 25 00 00 00 08 00 01 41 b5 92 78 e0 0a 2d+07:43:36.413 READ DMA EXT |
---|
230 | 25 00 00 00 08 00 01 41 b5 92 70 e0 0a 2d+07:43:36.413 READ DMA EXT |
---|
231 | 25 00 00 00 08 00 01 41 b5 92 68 e0 0a 2d+07:43:36.413 READ DMA EXT |
---|
232 | 25 00 00 00 08 00 01 41 b5 92 60 e0 0a 2d+07:43:36.413 READ DMA EXT |
---|
233 | 25 00 00 00 08 00 01 41 b5 92 58 e0 0a 2d+07:43:36.413 READ DMA EXT |
---|
234 | |
---|
235 | Error 145 [0] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) |
---|
236 | When the command that caused the error occurred, the device was active or idle. |
---|
237 | |
---|
238 | After command completion occurred, registers were: |
---|
239 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
240 | -- -- -- == -- == == == -- -- -- -- -- |
---|
241 | 40 -- 51 00 08 00 01 41 b5 89 f1 e0 00 Error: UNC 8 sectors at LBA = 0x141b589f1 = 5397383665 |
---|
242 | |
---|
243 | Commands leading to the command that caused the error were: |
---|
244 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
245 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
246 | 25 00 00 00 08 00 01 41 b5 89 f0 e0 0a 2d+07:43:34.558 READ DMA EXT |
---|
247 | 25 00 00 00 08 00 01 41 b5 89 e8 e0 0a 2d+07:43:34.558 READ DMA EXT |
---|
248 | 25 00 00 00 08 00 01 41 b5 89 e0 e0 0a 2d+07:43:34.558 READ DMA EXT |
---|
249 | 25 00 00 00 08 00 01 41 b5 89 d8 e0 0a 2d+07:43:34.558 READ DMA EXT |
---|
250 | 25 00 00 00 08 00 01 41 b5 89 d0 e0 0a 2d+07:43:34.558 READ DMA EXT |
---|
251 | |
---|
252 | Error 144 [23] occurred at disk power-on lifetime: 23082 hours (961 days + 18 hours) |
---|
253 | When the command that caused the error occurred, the device was active or idle. |
---|
254 | |
---|
255 | After command completion occurred, registers were: |
---|
256 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
257 | -- -- -- == -- == == == -- -- -- -- -- |
---|
258 | 40 -- 51 00 08 00 01 41 b5 81 69 e0 00 Error: UNC 8 sectors at LBA = 0x141b58169 = 5397381481 |
---|
259 | |
---|
260 | Commands leading to the command that caused the error were: |
---|
261 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
262 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
263 | 25 00 00 00 08 00 01 41 b5 81 68 e0 0a 2d+07:43:32.677 READ DMA EXT |
---|
264 | 25 00 00 00 08 00 01 41 b5 81 60 e0 0a 2d+07:43:32.677 READ DMA EXT |
---|
265 | 25 00 00 00 08 00 01 41 b5 81 58 e0 0a 2d+07:43:32.677 READ DMA EXT |
---|
266 | 25 00 00 00 08 00 01 41 b5 81 50 e0 0a 2d+07:43:32.677 READ DMA EXT |
---|
267 | 25 00 00 00 08 00 01 41 b5 81 48 e0 0a 2d+07:43:32.677 READ DMA EXT |
---|
268 | |
---|
269 | SMART Extended Self-test Log Version: 1 (1 sectors) |
---|
270 | Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error |
---|
271 | # 1 Short offline Completed without error 00% 23926 - |
---|
272 | # 2 Extended offline Completed without error 00% 23115 - |
---|
273 | # 3 Extended offline Aborted by host 90% 23105 - |
---|
274 | # 4 Short offline Completed without error 00% 23105 - |
---|
275 | # 5 Extended offline Aborted by host 90% 22935 - |
---|
276 | # 6 Short offline Completed without error 00% 22911 - |
---|
277 | # 7 Short captive Interrupted (host reset) 90% 22911 - |
---|
278 | # 8 Extended captive Interrupted (host reset) 90% 22901 - |
---|
279 | # 9 Extended offline Aborted by host 90% 22901 - |
---|
280 | #10 Short captive Completed without error 00% 22890 - |
---|
281 | |
---|
282 | SMART Selective self-test log data structure revision number 1 |
---|
283 | SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS |
---|
284 | 1 0 0 Not_testing |
---|
285 | 2 0 0 Not_testing |
---|
286 | 3 0 0 Not_testing |
---|
287 | 4 0 0 Not_testing |
---|
288 | 5 0 0 Not_testing |
---|
289 | Selective self-test flags (0x0): |
---|
290 | After scanning selected spans, do NOT read-scan remainder of disk. |
---|
291 | If Selective self-test is pending on power-up, resume after 0 minute delay. |
---|
292 | |
---|
293 | SCT Status Version: 3 |
---|
294 | SCT Version (vendor specific): 258 (0x0102) |
---|
295 | SCT Support Level: 1 |
---|
296 | Device State: Active (0) |
---|
297 | Current Temperature: 44 Celsius |
---|
298 | Power Cycle Min/Max Temperature: 40/45 Celsius |
---|
299 | Lifetime Min/Max Temperature: 19/54 Celsius |
---|
300 | Under/Over Temperature Limit Count: 0/0 |
---|
301 | Vendor specific: |
---|
302 | 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
---|
303 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |
---|
304 | |
---|
305 | SCT Temperature History Version: 2 |
---|
306 | Temperature Sampling Period: 1 minute |
---|
307 | Temperature Logging Interval: 1 minute |
---|
308 | Min/Max recommended Temperature: 0/60 Celsius |
---|
309 | Min/Max Temperature Limit: -41/85 Celsius |
---|
310 | Temperature History Size (Index): 478 (78) |
---|
311 | |
---|
312 | Index Estimated Time Temperature Celsius |
---|
313 | 79 2017-07-27 08:20 44 ************************* |
---|
314 | ... ..( 48 skipped). .. ************************* |
---|
315 | 128 2017-07-27 09:09 44 ************************* |
---|
316 | 129 2017-07-27 09:10 41 ********************** |
---|
317 | ... ..(178 skipped). .. ********************** |
---|
318 | 308 2017-07-27 12:09 41 ********************** |
---|
319 | 309 2017-07-27 12:10 42 *********************** |
---|
320 | ... ..(150 skipped). .. *********************** |
---|
321 | 460 2017-07-27 14:41 42 *********************** |
---|
322 | 461 2017-07-27 14:42 43 ************************ |
---|
323 | ... ..( 67 skipped). .. ************************ |
---|
324 | 51 2017-07-27 15:50 43 ************************ |
---|
325 | 52 2017-07-27 15:51 44 ************************* |
---|
326 | ... ..( 25 skipped). .. ************************* |
---|
327 | 78 2017-07-27 16:17 44 ************************* |
---|
328 | |
---|
329 | SCT Error Recovery Control: |
---|
330 | Read: 70 (7.0 seconds) |
---|
331 | Write: 70 (7.0 seconds) |
---|
332 | |
---|
333 | Device Statistics (GP/SMART Log 0x04) not supported |
---|
334 | |
---|
335 | SATA Phy Event Counters (GP Log 0x11) |
---|
336 | ID Size Value Description |
---|
337 | 0x0001 2 0 Command failed due to ICRC error |
---|
338 | 0x0002 2 0 R_ERR response for data FIS |
---|
339 | 0x0003 2 0 R_ERR response for device-to-host data FIS |
---|
340 | 0x0004 2 0 R_ERR response for host-to-device data FIS |
---|
341 | 0x0005 2 0 R_ERR response for non-data FIS |
---|
342 | 0x0006 2 0 R_ERR response for device-to-host non-data FIS |
---|
343 | 0x0007 2 0 R_ERR response for host-to-device non-data FIS |
---|
344 | 0x0008 2 0 Device-to-host non-data FIS retries |
---|
345 | 0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy |
---|
346 | 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET |
---|
347 | 0x000b 2 0 CRC errors within host-to-device FIS |
---|
348 | 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC |
---|
349 | 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC |
---|
350 | 0x8000 4 1653355 Vendor specific |
---|
351 | |
---|