| 1 | C:\smartmontools\bin>smartctl.exe --scan |
|---|
| 2 | /dev/sdb -d scsi # /dev/sdb, SCSI device |
|---|
| 3 | /dev/sdc -d scsi # /dev/sdc, SCSI device |
|---|
| 4 | /dev/sdd -d ata # /dev/sdd, ATA device |
|---|
| 5 | |
|---|
| 6 | C:\smartmontools\bin>smartctl.exe -A /dev/sdb |
|---|
| 7 | smartctl 6.5 2016-05-07 r4318 [x86_64-w64-mingw32-2008r2-sp1] (sf-6.5-1) |
|---|
| 8 | Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org |
|---|
| 9 | |
|---|
| 10 | === START OF READ SMART DATA SECTION === |
|---|
| 11 | Current Drive Temperature: 38 C |
|---|
| 12 | Drive Trip Temperature: 63 C |
|---|
| 13 | |
|---|
| 14 | Manufactured in week 39 of year 2014 |
|---|
| 15 | Specified cycle count over device lifetime: 0 |
|---|
| 16 | Accumulated start-stop cycles: 6398 |
|---|
| 17 | defect list format 6 unknown |
|---|
| 18 | Elements in grown defect list: 0 |
|---|
| 19 | |
|---|
| 20 | |
|---|
| 21 | C:\smartmontools\bin>smartctl.exe -x /dev/sdb |
|---|
| 22 | smartctl 6.5 2016-05-07 r4318 [x86_64-w64-mingw32-2008r2-sp1] (sf-6.5-1) |
|---|
| 23 | Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org |
|---|
| 24 | |
|---|
| 25 | === START OF INFORMATION SECTION === |
|---|
| 26 | Vendor: SanDisk |
|---|
| 27 | Product: DOPE1920S5xnNMRI |
|---|
| 28 | Revision: P018 |
|---|
| 29 | Compliance: SPC-4 |
|---|
| 30 | User Capacity: 1,950,389,400,960 bytes [1.95 TB] |
|---|
| 31 | Logical block size: 520 bytes |
|---|
| 32 | Physical block size: 4160 bytes |
|---|
| 33 | LU is resource provisioned, LBPRZ=1 |
|---|
| 34 | Rotation Rate: Solid State Device |
|---|
| 35 | Form Factor: 2.5 inches |
|---|
| 36 | Logical Unit id: 0x5001173100309154 |
|---|
| 37 | Serial number: FG00F2HW |
|---|
| 38 | Device type: disk |
|---|
| 39 | Transport protocol: SAS (SPL-3) |
|---|
| 40 | Local Time is: Tue Oct 17 14:10:49 2017 IST |
|---|
| 41 | SMART support is: Available - device has SMART capability. |
|---|
| 42 | SMART support is: Enabled |
|---|
| 43 | Temperature Warning: Enabled |
|---|
| 44 | Read Cache is: Enabled |
|---|
| 45 | Writeback Cache is: Disabled |
|---|
| 46 | |
|---|
| 47 | === START OF READ SMART DATA SECTION === |
|---|
| 48 | SMART Health Status: OK |
|---|
| 49 | |
|---|
| 50 | Percentage used endurance indicator: 1% |
|---|
| 51 | Current Drive Temperature: 38 C |
|---|
| 52 | Drive Trip Temperature: 63 C |
|---|
| 53 | |
|---|
| 54 | Manufactured in week 39 of year 2014 |
|---|
| 55 | Specified cycle count over device lifetime: 0 |
|---|
| 56 | Accumulated start-stop cycles: 6398 |
|---|
| 57 | defect list format 6 unknown |
|---|
| 58 | Elements in grown defect list: 0 |
|---|
| 59 | |
|---|
| 60 | Error counter log: |
|---|
| 61 | Errors Corrected by Total Correction Gigabytes Total |
|---|
| 62 | ECC rereads/ errors algorithm processed uncorrected |
|---|
| 63 | fast | delayed rewrites corrected invocations [10^9 bytes] errors |
|---|
| 64 | read: 0 0 0 0 0 1.020 0 |
|---|
| 65 | write: 0 0 0 0 0 0.708 0 |
|---|
| 66 | verify: 0 0 0 0 0 2.430 0 |
|---|
| 67 | |
|---|
| 68 | Non-medium error count: 30781 |
|---|
| 69 | |
|---|
| 70 | No self-tests have been logged |
|---|
| 71 | |
|---|
| 72 | Background scan results log |
|---|
| 73 | Status: no scans active |
|---|
| 74 | Accumulated power on time, hours:minutes 3396:42 [203802 minutes] |
|---|
| 75 | Number of background scans performed: 0, scan progress: 0.00% |
|---|
| 76 | Number of background medium scans performed: 0 |
|---|
| 77 | |
|---|
| 78 | # when lba(hex) [sk,asc,ascq] reassign_status |
|---|
| 79 | 1 0:00 0000000000000000 [0,0,0] Reserved [0x0] |
|---|
| 80 | |
|---|
| 81 | Protocol Specific port log page for SAS SSP |
|---|
| 82 | relative target port id = 1 |
|---|
| 83 | generation code = 1 |
|---|
| 84 | number of phys = 1 |
|---|
| 85 | phy identifier = 0 |
|---|
| 86 | attached device type: SAS or SATA device |
|---|
| 87 | attached reason: loss of dword synchronization |
|---|
| 88 | reason: power on |
|---|
| 89 | negotiated logical link rate: phy enabled; 6 Gbps |
|---|
| 90 | attached initiator port: ssp=1 stp=1 smp=1 |
|---|
| 91 | attached target port: ssp=0 stp=0 smp=0 |
|---|
| 92 | SAS address = 0x5001173100309155 |
|---|
| 93 | attached SAS address = 0x500605b0091c3bf0 |
|---|
| 94 | attached phy identifier = 4 |
|---|
| 95 | Invalid DWORD count = 0 |
|---|
| 96 | Running disparity error count = 0 |
|---|
| 97 | Loss of DWORD synchronization = 0 |
|---|
| 98 | Phy reset problem = 0 |
|---|
| 99 | Phy event descriptors: |
|---|
| 100 | Invalid word count: 0 |
|---|
| 101 | Running disparity error count: 0 |
|---|
| 102 | Loss of dword synchronization count: 0 |
|---|
| 103 | Phy reset problem count: 0 |
|---|
| 104 | phy identifier = 0 |
|---|
| 105 | attached device type: no device attached |
|---|
| 106 | attached reason: unknown |
|---|
| 107 | reason: unknown |
|---|
| 108 | negotiated logical link rate: phy enabled; unknown |
|---|
| 109 | attached initiator port: ssp=0 stp=0 smp=0 |
|---|
| 110 | attached target port: ssp=0 stp=0 smp=0 |
|---|
| 111 | SAS address = 0x2 |
|---|
| 112 | attached SAS address = 0x0 |
|---|
| 113 | attached phy identifier = 0 |
|---|
| 114 | Invalid DWORD count = 0 |
|---|
| 115 | Running disparity error count = 4 |
|---|
| 116 | Loss of DWORD synchronization = 0 |
|---|
| 117 | Phy reset problem = 0 |
|---|
| 118 | relative target port id = 2 |
|---|
| 119 | generation code = 1 |
|---|
| 120 | number of phys = 1 |
|---|
| 121 | phy identifier = 1 |
|---|
| 122 | attached device type: no device attached |
|---|
| 123 | attached reason: unknown |
|---|
| 124 | reason: unknown |
|---|
| 125 | negotiated logical link rate: phy enabled; unknown |
|---|
| 126 | attached initiator port: ssp=0 stp=0 smp=0 |
|---|
| 127 | attached target port: ssp=0 stp=0 smp=0 |
|---|
| 128 | SAS address = 0x5001173100309156 |
|---|
| 129 | attached SAS address = 0x0 |
|---|
| 130 | attached phy identifier = 0 |
|---|
| 131 | Invalid DWORD count = 0 |
|---|
| 132 | Running disparity error count = 0 |
|---|
| 133 | Loss of DWORD synchronization = 0 |
|---|
| 134 | Phy reset problem = 0 |
|---|
| 135 | Phy event descriptors: |
|---|
| 136 | Invalid word count: 0 |
|---|
| 137 | Running disparity error count: 0 |
|---|
| 138 | Loss of dword synchronization count: 0 |
|---|
| 139 | Phy reset problem count: 0 |
|---|
| 140 | phy identifier = 0 |
|---|
| 141 | attached device type: no device attached |
|---|
| 142 | attached reason: unknown |
|---|
| 143 | reason: unknown |
|---|
| 144 | negotiated logical link rate: phy enabled; unknown |
|---|
| 145 | attached initiator port: ssp=0 stp=0 smp=0 |
|---|
| 146 | attached target port: ssp=0 stp=0 smp=0 |
|---|
| 147 | SAS address = 0x2 |
|---|
| 148 | attached SAS address = 0x0 |
|---|
| 149 | attached phy identifier = 0 |
|---|
| 150 | Invalid DWORD count = 0 |
|---|
| 151 | Running disparity error count = 4 |
|---|
| 152 | Loss of DWORD synchronization = 0 |
|---|
| 153 | Phy reset problem = 0 |
|---|
| 154 | |
|---|
