| 1 | smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.4.75-loc] (local build)
|
|---|
| 2 | Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
|
|---|
| 3 |
|
|---|
| 4 | === START OF INFORMATION SECTION ===
|
|---|
| 5 | Vendor: SEAGATE
|
|---|
| 6 | Product: ST8000NM0065
|
|---|
| 7 | Revision: K002
|
|---|
| 8 | Compliance: SPC-4
|
|---|
| 9 | User Capacity: 8,001,563,222,016 bytes [8.00 TB]
|
|---|
| 10 | Logical block size: 4096 bytes
|
|---|
| 11 | LU is fully provisioned
|
|---|
| 12 | Rotation Rate: 7200 rpm
|
|---|
| 13 | Form Factor: 3.5 inches
|
|---|
| 14 | Device type: disk
|
|---|
| 15 | Transport protocol: SAS (SPL-3)
|
|---|
| 16 | Local Time is: Mon Aug 28 07:36:56 2017 PDT
|
|---|
| 17 | SMART support is: Available - device has SMART capability.
|
|---|
| 18 | SMART support is: Enabled
|
|---|
| 19 | Temperature Warning: Enabled
|
|---|
| 20 | Read Cache is: Enabled
|
|---|
| 21 | Writeback Cache is: Enabled
|
|---|
| 22 |
|
|---|
| 23 | === START OF READ SMART DATA SECTION ===
|
|---|
| 24 | SMART Health Status: OK
|
|---|
| 25 |
|
|---|
| 26 | Current Drive Temperature: 37 C
|
|---|
| 27 | Drive Trip Temperature: 60 C
|
|---|
| 28 |
|
|---|
| 29 | Manufactured in week 23 of year 2016
|
|---|
| 30 | Specified cycle count over device lifetime: 10000
|
|---|
| 31 | Accumulated start-stop cycles: 56
|
|---|
| 32 | Specified load-unload count over device lifetime: 300000
|
|---|
| 33 | Accumulated load-unload cycles: 15049
|
|---|
| 34 | Elements in grown defect list: 0
|
|---|
| 35 |
|
|---|
| 36 | Vendor (Seagate) cache information
|
|---|
| 37 | Blocks sent to initiator = 4896
|
|---|
| 38 | Blocks received from initiator = 6972
|
|---|
| 39 | Blocks read from cache and sent to initiator = 8078
|
|---|
| 40 | Number of read and write commands whose size <= segment size = 128
|
|---|
| 41 | Number of read and write commands whose size > segment size = 4
|
|---|
| 42 |
|
|---|
| 43 | Vendor (Seagate/Hitachi) factory information
|
|---|
| 44 | number of hours powered up = 7448.95
|
|---|
| 45 | number of minutes until next internal SMART test = 50
|
|---|
| 46 |
|
|---|
| 47 | Error counter log:
|
|---|
| 48 | Errors Corrected by Total Correction Gigabytes Total
|
|---|
| 49 | ECC rereads/ errors algorithm processed uncorrected
|
|---|
| 50 | fast | delayed rewrites corrected invocations [10^9 bytes] errors
|
|---|
| 51 | read: 42938 0 0 42938 0 0.020 0
|
|---|
| 52 | write: 0 0 0 0 0 0.495 0
|
|---|
| 53 |
|
|---|
| 54 | Non-medium error count: 16
|
|---|
| 55 |
|
|---|
| 56 |
|
|---|
| 57 | [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
|
|---|
| 58 | SMART Self-test log
|
|---|
| 59 | Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
|
|---|
| 60 | Description number (hours)
|
|---|
| 61 | # 1 Background short Completed - 7448 - [- - -]
|
|---|
| 62 |
|
|---|
| 63 | Long (extended) Self Test duration: 47220 seconds [787.0 minutes]
|
|---|
| 64 |
|
|---|
| 65 | Background scan results log
|
|---|
| 66 | Status: no scans active
|
|---|
| 67 | Accumulated power on time, hours:minutes 7448:57 [446937 minutes]
|
|---|
| 68 | Number of background scans performed: 0, scan progress: 0.00%
|
|---|
| 69 | Number of background medium scans performed: 0
|
|---|
| 70 |
|
|---|
| 71 | Protocol Specific port log page for SAS SSP
|
|---|
| 72 | relative target port id = 1
|
|---|
| 73 | generation code = 0
|
|---|
| 74 | number of phys = 1
|
|---|
| 75 | phy identifier = 0
|
|---|
| 76 | attached device type: SAS or SATA device
|
|---|
| 77 | attached reason: power on
|
|---|
| 78 | reason: loss of dword synchronization
|
|---|
| 79 | negotiated logical link rate: phy enabled; 6 Gbps
|
|---|
| 80 | attached initiator port: ssp=1 stp=1 smp=1
|
|---|
| 81 | attached target port: ssp=0 stp=0 smp=0
|
|---|
| 82 | SAS address = 0x5000c50085893a3d
|
|---|
| 83 | attached SAS address = 0x500605b009a1aa60
|
|---|
| 84 | attached phy identifier = 0
|
|---|
| 85 | Invalid DWORD count = 0
|
|---|
| 86 | Running disparity error count = 0
|
|---|
| 87 | Loss of DWORD synchronization = 36
|
|---|
| 88 | Phy reset problem = 0
|
|---|
| 89 | Phy event descriptors:
|
|---|
| 90 | Invalid word count: 0
|
|---|
| 91 | Running disparity error count: 0
|
|---|
| 92 | Loss of dword synchronization count: 36
|
|---|
| 93 | Phy reset problem count: 0
|
|---|
| 94 | relative target port id = 2
|
|---|
| 95 | generation code = 0
|
|---|
| 96 | number of phys = 1
|
|---|
| 97 | phy identifier = 1
|
|---|
| 98 | attached device type: no device attached
|
|---|
| 99 | attached reason: unknown
|
|---|
| 100 | reason: unknown
|
|---|
| 101 | negotiated logical link rate: phy enabled; unknown
|
|---|
| 102 | attached initiator port: ssp=0 stp=0 smp=0
|
|---|
| 103 | attached target port: ssp=0 stp=0 smp=0
|
|---|
| 104 | SAS address = 0x5000c50085893a3e
|
|---|
| 105 | attached SAS address = 0x0
|
|---|
| 106 | attached phy identifier = 0
|
|---|
| 107 | Invalid DWORD count = 0
|
|---|
| 108 | Running disparity error count = 0
|
|---|
| 109 | Loss of DWORD synchronization = 0
|
|---|
| 110 | Phy reset problem = 0
|
|---|
| 111 | Phy event descriptors:
|
|---|
| 112 | Invalid word count: 0
|
|---|
| 113 | Running disparity error count: 0
|
|---|
| 114 | Loss of dword synchronization count: 0
|
|---|
| 115 | Phy reset problem count: 0
|
|---|
| 116 |
|
|---|
