1 | smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.4.75-loc] (local build) |
---|
2 | Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org |
---|
3 | |
---|
4 | === START OF INFORMATION SECTION === |
---|
5 | Vendor: SEAGATE |
---|
6 | Product: ST4000NM0023 |
---|
7 | Revision: 0003 |
---|
8 | Compliance: SPC-4 |
---|
9 | User Capacity: 4,000,787,030,016 bytes [4.00 TB] |
---|
10 | Logical block size: 512 bytes |
---|
11 | LU is fully provisioned |
---|
12 | Rotation Rate: 7200 rpm |
---|
13 | Form Factor: 3.5 inches |
---|
14 | Device type: disk |
---|
15 | Transport protocol: SAS (SPL-3) |
---|
16 | Local Time is: Mon Aug 28 07:36:17 2017 PDT |
---|
17 | SMART support is: Available - device has SMART capability. |
---|
18 | SMART support is: Enabled |
---|
19 | Temperature Warning: Enabled |
---|
20 | Read Cache is: Enabled |
---|
21 | Writeback Cache is: Enabled |
---|
22 | |
---|
23 | === START OF READ SMART DATA SECTION === |
---|
24 | SMART Health Status: OK |
---|
25 | |
---|
26 | Current Drive Temperature: 39 C |
---|
27 | Drive Trip Temperature: 40 C |
---|
28 | |
---|
29 | Manufactured in week 43 of year 2013 |
---|
30 | Specified cycle count over device lifetime: 10000 |
---|
31 | Accumulated start-stop cycles: 217 |
---|
32 | Specified load-unload count over device lifetime: 300000 |
---|
33 | Accumulated load-unload cycles: 1482 |
---|
34 | Elements in grown defect list: 3 |
---|
35 | |
---|
36 | Vendor (Seagate) cache information |
---|
37 | Blocks sent to initiator = 1820284864 |
---|
38 | Blocks received from initiator = 3344349675 |
---|
39 | Blocks read from cache and sent to initiator = 46541887 |
---|
40 | Number of read and write commands whose size <= segment size = 32784521 |
---|
41 | Number of read and write commands whose size > segment size = 855654 |
---|
42 | |
---|
43 | Vendor (Seagate/Hitachi) factory information |
---|
44 | number of hours powered up = 30883.95 |
---|
45 | number of minutes until next internal SMART test = 36 |
---|
46 | |
---|
47 | Error counter log: |
---|
48 | Errors Corrected by Total Correction Gigabytes Total |
---|
49 | ECC rereads/ errors algorithm processed uncorrected |
---|
50 | fast | delayed rewrites corrected invocations [10^9 bytes] errors |
---|
51 | read: 2816389502 0 0 2816389502 0 931.986 0 |
---|
52 | write: 0 0 0 0 0 41073.661 0 |
---|
53 | |
---|
54 | Non-medium error count: 0 |
---|
55 | |
---|
56 | |
---|
57 | [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] |
---|
58 | SMART Self-test log |
---|
59 | Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] |
---|
60 | Description number (hours) |
---|
61 | # 1 Background short Completed - 30883 - [- - -] |
---|
62 | |
---|
63 | Long (extended) Self Test duration: 32700 seconds [545.0 minutes] |
---|
64 | |
---|
65 | Background scan results log |
---|
66 | Status: waiting until BMS interval timer expires |
---|
67 | Accumulated power on time, hours:minutes 30883:57 [1853037 minutes] |
---|
68 | Number of background scans performed: 413, scan progress: 0.00% |
---|
69 | Number of background medium scans performed: 413 |
---|
70 | |
---|
71 | # when lba(hex) [sk,asc,ascq] reassign_status |
---|
72 | 1 29408:32 000000004dd36872 [1,18,1] Successfully reassigned |
---|
73 | 2 29480:08 000000004dd35cad [1,18,1] Successfully reassigned |
---|
74 | 3 29480:08 000000004dd37437 [1,18,1] Successfully reassigned |
---|
75 | |
---|
76 | Protocol Specific port log page for SAS SSP |
---|
77 | relative target port id = 1 |
---|
78 | generation code = 36 |
---|
79 | number of phys = 1 |
---|
80 | phy identifier = 0 |
---|
81 | attached device type: SAS or SATA device |
---|
82 | attached reason: unknown |
---|
83 | reason: unknown |
---|
84 | negotiated logical link rate: phy enabled; 6 Gbps |
---|
85 | attached initiator port: ssp=1 stp=1 smp=1 |
---|
86 | attached target port: ssp=0 stp=0 smp=0 |
---|
87 | SAS address = 0x5000c50057a1620d |
---|
88 | attached SAS address = 0x500605b009a1aa62 |
---|
89 | attached phy identifier = 2 |
---|
90 | Invalid DWORD count = 0 |
---|
91 | Running disparity error count = 0 |
---|
92 | Loss of DWORD synchronization = 39 |
---|
93 | Phy reset problem = 0 |
---|
94 | Phy event descriptors: |
---|
95 | Invalid word count: 0 |
---|
96 | Running disparity error count: 0 |
---|
97 | Loss of dword synchronization count: 39 |
---|
98 | Phy reset problem count: 0 |
---|
99 | relative target port id = 2 |
---|
100 | generation code = 36 |
---|
101 | number of phys = 1 |
---|
102 | phy identifier = 1 |
---|
103 | attached device type: no device attached |
---|
104 | attached reason: unknown |
---|
105 | reason: unknown |
---|
106 | negotiated logical link rate: phy enabled; unknown |
---|
107 | attached initiator port: ssp=0 stp=0 smp=0 |
---|
108 | attached target port: ssp=0 stp=0 smp=0 |
---|
109 | SAS address = 0x5000c50057a1620e |
---|
110 | attached SAS address = 0x0 |
---|
111 | attached phy identifier = 0 |
---|
112 | Invalid DWORD count = 0 |
---|
113 | Running disparity error count = 0 |
---|
114 | Loss of DWORD synchronization = 0 |
---|
115 | Phy reset problem = 0 |
---|
116 | Phy event descriptors: |
---|
117 | Invalid word count: 0 |
---|
118 | Running disparity error count: 0 |
---|
119 | Loss of dword synchronization count: 0 |
---|
120 | Phy reset problem count: 0 |
---|
121 | |
---|