| 1 | smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.12.0+] (local build) |
|---|
| 2 | Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org |
|---|
| 3 | |
|---|
| 4 | === START OF INFORMATION SECTION === |
|---|
| 5 | Model Family: SAMSUNG SpinPoint M6 |
|---|
| 6 | Device Model: SAMSUNG HM320JI |
|---|
| 7 | Serial Number: S1U6J56SB06960 |
|---|
| 8 | LU WWN Device Id: 5 0f0000 063206960 |
|---|
| 9 | Firmware Version: 2SS00_01 |
|---|
| 10 | User Capacity: 320.072.933.376 bytes [320 GB] |
|---|
| 11 | Sector Size: 512 bytes logical/physical |
|---|
| 12 | Device is: In smartctl database [for details use: -P show] |
|---|
| 13 | ATA Version is: ATA8-ACS, ATA/ATAPI-7 T13/1532D revision 0 |
|---|
| 14 | SATA Version is: SATA 2.5, 1.5 Gb/s |
|---|
| 15 | Local Time is: Thu Jul 6 10:15:28 2017 -03 |
|---|
| 16 | SMART support is: Available - device has SMART capability. |
|---|
| 17 | SMART support is: Enabled |
|---|
| 18 | |
|---|
| 19 | === START OF READ SMART DATA SECTION === |
|---|
| 20 | SMART overall-health self-assessment test result: PASSED |
|---|
| 21 | |
|---|
| 22 | General SMART Values: |
|---|
| 23 | Offline data collection status: (0x00) Offline data collection activity |
|---|
| 24 | was never started. |
|---|
| 25 | Auto Offline Data Collection: Disabled. |
|---|
| 26 | Self-test execution status: ( 0) The previous self-test routine completed |
|---|
| 27 | without error or no self-test has ever |
|---|
| 28 | been run. |
|---|
| 29 | Total time to complete Offline |
|---|
| 30 | data collection: ( 113) seconds. |
|---|
| 31 | Offline data collection |
|---|
| 32 | capabilities: (0x5b) SMART execute Offline immediate. |
|---|
| 33 | Auto Offline data collection on/off support. |
|---|
| 34 | Suspend Offline collection upon new |
|---|
| 35 | command. |
|---|
| 36 | Offline surface scan supported. |
|---|
| 37 | Self-test supported. |
|---|
| 38 | No Conveyance Self-test supported. |
|---|
| 39 | Selective Self-test supported. |
|---|
| 40 | SMART capabilities: (0x0003) Saves SMART data before entering |
|---|
| 41 | power-saving mode. |
|---|
| 42 | Supports SMART auto save timer. |
|---|
| 43 | Error logging capability: (0x01) Error logging supported. |
|---|
| 44 | General Purpose Logging supported. |
|---|
| 45 | Short self-test routine |
|---|
| 46 | recommended polling time: ( 2) minutes. |
|---|
| 47 | Extended self-test routine |
|---|
| 48 | recommended polling time: ( 113) minutes. |
|---|
| 49 | SCT capabilities: (0x003f) SCT Status supported. |
|---|
| 50 | SCT Error Recovery Control supported. |
|---|
| 51 | SCT Feature Control supported. |
|---|
| 52 | SCT Data Table supported. |
|---|
| 53 | |
|---|
| 54 | SMART Attributes Data Structure revision number: 16 |
|---|
| 55 | Vendor Specific SMART Attributes with Thresholds: |
|---|
| 56 | ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE |
|---|
| 57 | 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 12 |
|---|
| 58 | 3 Spin_Up_Time 0x0007 252 252 025 Pre-fail Always - 2875 |
|---|
| 59 | 4 Start_Stop_Count 0x0032 096 096 000 Old_age Always - 4673 |
|---|
| 60 | 5 Reallocated_Sector_Ct 0x0033 096 096 010 Pre-fail Always - 42 |
|---|
| 61 | 7 Seek_Error_Rate 0x000e 252 252 051 Old_age Always - 0 |
|---|
| 62 | 8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0 |
|---|
| 63 | 9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 3705 |
|---|
| 64 | 10 Spin_Retry_Count 0x0032 100 100 051 Old_age Always - 3 |
|---|
| 65 | 12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2551 |
|---|
| 66 | 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 6343 |
|---|
| 67 | 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 728 |
|---|
| 68 | 194 Temperature_Celsius 0x0022 163 073 000 Old_age Always - 25 (Min/Max 5/56) |
|---|
| 69 | 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 25 |
|---|
| 70 | 196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0 |
|---|
| 71 | 197 Current_Pending_Sector 0x0012 252 100 000 Old_age Always - 0 |
|---|
| 72 | 198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0 |
|---|
| 73 | 199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 13 |
|---|
| 74 | 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 5 |
|---|
| 75 | 201 Soft_Read_Error_Rate 0x0032 252 252 000 Old_age Always - 0 |
|---|
| 76 | 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 348 |
|---|
| 77 | 225 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 30137 |
|---|
| 78 | |
|---|
| 79 | SMART Error Log Version: 1 |
|---|
| 80 | No Errors Logged |
|---|
| 81 | |
|---|
| 82 | SMART Self-test log structure revision number 1 |
|---|
| 83 | No self-tests have been logged. [To run self-tests, use: smartctl -t] |
|---|
| 84 | |
|---|
| 85 | SMART Selective self-test log data structure revision number 0 |
|---|
| 86 | Note: revision number not 1 implies that no selective self-test has ever been run |
|---|
| 87 | SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS |
|---|
| 88 | 1 0 0 Not_testing |
|---|
| 89 | 2 0 0 Not_testing |
|---|
| 90 | 3 0 0 Not_testing |
|---|
| 91 | 4 0 0 Not_testing |
|---|
| 92 | 5 0 0 Not_testing |
|---|
| 93 | Selective self-test flags (0x0): |
|---|
| 94 | After scanning selected spans, do NOT read-scan remainder of disk. |
|---|
| 95 | If Selective self-test is pending on power-up, resume after 0 minute delay. |
|---|
| 96 | |
|---|
