| 1 | smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.10.0-327.13.1.el7.x86_64] (local build) |
|---|
| 2 | Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org |
|---|
| 3 | |
|---|
| 4 | === START OF INFORMATION SECTION === |
|---|
| 5 | Vendor: TOSHIBA |
|---|
| 6 | Product: PX04SRB384 |
|---|
| 7 | Revision: AM04 |
|---|
| 8 | User Capacity: 3,840,755,982,336 bytes [3.84 TB] |
|---|
| 9 | Logical block size: 512 bytes |
|---|
| 10 | LU is resource provisioned, LBPRZ=1 |
|---|
| 11 | Rotation Rate: Solid State Device |
|---|
| 12 | Form Factor: 2.5 inches |
|---|
| 13 | Device type: disk |
|---|
| 14 | Transport protocol: SAS |
|---|
| 15 | Local Time is: Thu Nov 17 22:02:05 2016 UTC |
|---|
| 16 | SMART support is: Available - device has SMART capability. |
|---|
| 17 | SMART support is: Enabled |
|---|
| 18 | Temperature Warning: Disabled or Not Supported |
|---|
| 19 | Read Cache is: Enabled |
|---|
| 20 | Writeback Cache is: Disabled |
|---|
| 21 | |
|---|
| 22 | === START OF READ SMART DATA SECTION === |
|---|
| 23 | SMART Health Status: OK |
|---|
| 24 | |
|---|
| 25 | SS Media used endurance indicator: 0% |
|---|
| 26 | Current Drive Temperature: 25 C |
|---|
| 27 | Drive Trip Temperature: 64 C |
|---|
| 28 | |
|---|
| 29 | Manufactured in week 03 of year 2016 |
|---|
| 30 | Error counter log: |
|---|
| 31 | Errors Corrected by Total Correction Gigabytes Total |
|---|
| 32 | ECC rereads/ errors algorithm processed uncorrected |
|---|
| 33 | fast | delayed rewrites corrected invocations [10^9 bytes] errors |
|---|
| 34 | read: 0 0 0 0 0 13.971 0 |
|---|
| 35 | write: 0 0 0 0 0 27084.072 0 |
|---|
| 36 | verify: 0 0 0 0 0 5.649 0 |
|---|
| 37 | |
|---|
| 38 | Non-medium error count: 227 |
|---|
| 39 | |
|---|
| 40 | SMART Self-test log |
|---|
| 41 | Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] |
|---|
| 42 | Description number (hours) |
|---|
| 43 | # 1 Background short Completed 96 5270 - [- - -] |
|---|
| 44 | # 2 Background short Completed 96 12 - [- - -] |
|---|
| 45 | # 3 Background long Completed 96 11 - [- - -] |
|---|
| 46 | Long (extended) Self Test duration: 1800 seconds [30.0 minutes] |
|---|
| 47 | |
|---|
| 48 | Background scan results log |
|---|
| 49 | Status: no scans active |
|---|
| 50 | Accumulated power on time, hours:minutes 5270:25 [316225 minutes] |
|---|
| 51 | Number of background scans performed: 0, scan progress: 0.00% |
|---|
| 52 | Number of background medium scans performed: 0 |
|---|
| 53 | |
|---|
| 54 | Protocol Specific port log page for SAS SSP |
|---|
| 55 | relative target port id = 1 |
|---|
| 56 | generation code = 2 |
|---|
| 57 | number of phys = 1 |
|---|
| 58 | phy identifier = 0 |
|---|
| 59 | attached device type: expander device |
|---|
| 60 | attached reason: SMP phy control function |
|---|
| 61 | reason: loss of dword synchronization |
|---|
| 62 | negotiated logical link rate: reserved [11] |
|---|
| 63 | attached initiator port: ssp=0 stp=0 smp=0 |
|---|
| 64 | attached target port: ssp=0 stp=0 smp=1 |
|---|
| 65 | SAS address = 0x50000396cc89c2f6 |
|---|
| 66 | attached SAS address = 0x500056b3edadbaff |
|---|
| 67 | attached phy identifier = 2 |
|---|
| 68 | Invalid DWORD count = 4 |
|---|
| 69 | Running disparity error count = 4 |
|---|
| 70 | Loss of DWORD synchronization = 1 |
|---|
| 71 | Phy reset problem = 0 |
|---|
| 72 | relative target port id = 2 |
|---|
| 73 | generation code = 2 |
|---|
| 74 | number of phys = 1 |
|---|
| 75 | phy identifier = 1 |
|---|
| 76 | attached device type: no device attached |
|---|
| 77 | attached reason: unknown |
|---|
| 78 | reason: unknown |
|---|
| 79 | negotiated logical link rate: phy enabled; unknown |
|---|
| 80 | attached initiator port: ssp=0 stp=0 smp=0 |
|---|
| 81 | attached target port: ssp=0 stp=0 smp=0 |
|---|
| 82 | SAS address = 0x50000396cc89c2f7 |
|---|
| 83 | attached SAS address = 0x0 |
|---|
| 84 | attached phy identifier = 0 |
|---|
| 85 | Invalid DWORD count = 0 |
|---|
| 86 | Running disparity error count = 0 |
|---|
| 87 | Loss of DWORD synchronization = 0 |
|---|
| 88 | Phy reset problem = 0 |
|---|
| 89 | |
|---|
