| 1 | XXX@XXX:~/devel/smartmontools$ dmesg
|
|---|
| 2 | ...
|
|---|
| 3 | [ 655.488607] usb 4-3: new SuperSpeed USB device number 5 using xhci_hcd
|
|---|
| 4 | [ 655.502908] usb 4-3: New USB device found, idVendor=067b, idProduct=2773
|
|---|
| 5 | [ 655.502912] usb 4-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
|
|---|
| 6 | [ 655.502915] usb 4-3: Product: ATAPI-6 Bridge Controller
|
|---|
| 7 | [ 655.502917] usb 4-3: Manufacturer: Prolific Technology Inc.
|
|---|
| 8 | [ 655.502920] usb 4-3: SerialNumber: 0123456789000000005
|
|---|
| 9 | [ 655.503244] usb 4-3: Set SEL for device-initiated U1 failed.
|
|---|
| 10 | [ 655.503317] usb 4-3: Set SEL for device-initiated U2 failed.
|
|---|
| 11 | [ 655.503385] usb-storage 4-3:1.0: USB Mass Storage device detected
|
|---|
| 12 | [ 655.503547] scsi7 : usb-storage 4-3:1.0
|
|---|
| 13 | [ 655.503626] usb 4-3: Set SEL for device-initiated U1 failed.
|
|---|
| 14 | [ 655.503702] usb 4-3: Set SEL for device-initiated U2 failed.
|
|---|
| 15 | [ 656.501907] scsi 7:0:0:0: Direct-Access WDC WD20 EARS-00MVWB0 51.0 PQ: 0 ANSI: 0
|
|---|
| 16 | [ 656.502163] sd 7:0:0:0: Attached scsi generic sg1 type 0
|
|---|
| 17 | [ 656.502502] sd 7:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
|
|---|
| 18 | [ 656.502762] sd 7:0:0:0: [sdb] Write Protect is off
|
|---|
| 19 | [ 656.502766] sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
|
|---|
| 20 | [ 656.503124] sd 7:0:0:0: [sdb] No Caching mode page found
|
|---|
| 21 | [ 656.503128] sd 7:0:0:0: [sdb] Assuming drive cache: write through
|
|---|
| 22 | [ 656.505011] sd 7:0:0:0: [sdb] No Caching mode page found
|
|---|
| 23 | [ 656.505016] sd 7:0:0:0: [sdb] Assuming drive cache: write through
|
|---|
| 24 | [ 656.563094] sdb: sdb1 sdb2
|
|---|
| 25 | [ 656.564210] sd 7:0:0:0: [sdb] No Caching mode page found
|
|---|
| 26 | [ 656.564215] sd 7:0:0:0: [sdb] Assuming drive cache: write through
|
|---|
| 27 | [ 656.564218] sd 7:0:0:0: [sdb] Attached SCSI disk
|
|---|
| 28 |
|
|---|
| 29 | XXX@XXX:~/devel/smartmontools$ sudo ./smartctl -x /dev/sdb
|
|---|
| 30 | smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.13.0-39-generic] (local build)
|
|---|
| 31 | Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
|
|---|
| 32 |
|
|---|
| 33 | === START OF INFORMATION SECTION ===
|
|---|
| 34 | Model Family: Western Digital Caviar Green (AF)
|
|---|
| 35 | Device Model: WDC WD20EARS-00MVWB0
|
|---|
| 36 | Serial Number: WD-WMAZA0665703
|
|---|
| 37 | LU WWN Device Id: 5 0014ee 0ad14039a
|
|---|
| 38 | Firmware Version: 51.0AB51
|
|---|
| 39 | User Capacity: 2.000.398.934.016 bytes [2,00 TB]
|
|---|
| 40 | Sector Size: 512 bytes logical/physical
|
|---|
| 41 | Device is: In smartctl database [for details use: -P show]
|
|---|
| 42 | ATA Version is: ATA8-ACS (minor revision not indicated)
|
|---|
| 43 | SATA Version is: SATA 2.6, 3.0 Gb/s
|
|---|
| 44 | Local Time is: Tue Nov 4 20:31:54 2014 CET
|
|---|
| 45 | SMART support is: Available - device has SMART capability.
|
|---|
| 46 | SMART support is: Enabled
|
|---|
| 47 | AAM feature is: Disabled
|
|---|
| 48 | APM feature is: Unavailable
|
|---|
| 49 | Rd look-ahead is: Enabled
|
|---|
| 50 | Write cache is: Enabled
|
|---|
| 51 | ATA Security is: Disabled, NOT FROZEN [SEC1]
|
|---|
| 52 | Write SCT (Get) Feature Control Command failed: DATA OUT ATA commands not implemented [Prolific]
|
|---|
| 53 | Wt Cache Reorder: Unknown (SCT Feature Control command failed)
|
|---|
| 54 |
|
|---|
| 55 | === START OF READ SMART DATA SECTION ===
|
|---|
| 56 | SMART overall-health self-assessment test result: PASSED
|
|---|
| 57 |
|
|---|
| 58 | General SMART Values:
|
|---|
| 59 | Offline data collection status: (0x85) Offline data collection activity
|
|---|
| 60 | was aborted by an interrupting command from host.
|
|---|
| 61 | Auto Offline Data Collection: Enabled.
|
|---|
| 62 | Self-test execution status: ( 0) The previous self-test routine completed
|
|---|
| 63 | without error or no self-test has ever
|
|---|
| 64 | been run.
|
|---|
| 65 | Total time to complete Offline
|
|---|
| 66 | data collection: (36480) seconds.
|
|---|
| 67 | Offline data collection
|
|---|
| 68 | capabilities: (0x7b) SMART execute Offline immediate.
|
|---|
| 69 | Auto Offline data collection on/off support.
|
|---|
| 70 | Suspend Offline collection upon new
|
|---|
| 71 | command.
|
|---|
| 72 | Offline surface scan supported.
|
|---|
| 73 | Self-test supported.
|
|---|
| 74 | Conveyance Self-test supported.
|
|---|
| 75 | Selective Self-test supported.
|
|---|
| 76 | SMART capabilities: (0x0003) Saves SMART data before entering
|
|---|
| 77 | power-saving mode.
|
|---|
| 78 | Supports SMART auto save timer.
|
|---|
| 79 | Error logging capability: (0x01) Error logging supported.
|
|---|
| 80 | General Purpose Logging supported.
|
|---|
| 81 | Short self-test routine
|
|---|
| 82 | recommended polling time: ( 2) minutes.
|
|---|
| 83 | Extended self-test routine
|
|---|
| 84 | recommended polling time: ( 352) minutes.
|
|---|
| 85 | Conveyance self-test routine
|
|---|
| 86 | recommended polling time: ( 5) minutes.
|
|---|
| 87 | SCT capabilities: (0x3035) SCT Status supported.
|
|---|
| 88 | SCT Feature Control supported.
|
|---|
| 89 | SCT Data Table supported.
|
|---|
| 90 |
|
|---|
| 91 | SMART Attributes Data Structure revision number: 16
|
|---|
| 92 | Vendor Specific SMART Attributes with Thresholds:
|
|---|
| 93 | ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
|
|---|
| 94 | 1 Raw_Read_Error_Rate POSR-K 198 198 051 - 744
|
|---|
| 95 | 3 Spin_Up_Time POS--K 172 160 021 - 6375
|
|---|
| 96 | 4 Start_Stop_Count -O--CK 098 098 000 - 2693
|
|---|
| 97 | 5 Reallocated_Sector_Ct PO--CK 196 196 140 - 83
|
|---|
| 98 | 7 Seek_Error_Rate -OSR-K 200 200 000 - 0
|
|---|
| 99 | 9 Power_On_Hours -O--CK 066 066 000 - 25155
|
|---|
| 100 | 10 Spin_Retry_Count -O--CK 100 100 000 - 0
|
|---|
| 101 | 11 Calibration_Retry_Count -O--CK 100 253 000 - 0
|
|---|
| 102 | 12 Power_Cycle_Count -O--CK 100 100 000 - 88
|
|---|
| 103 | 192 Power-Off_Retract_Count -O--CK 200 200 000 - 48
|
|---|
| 104 | 193 Load_Cycle_Count -O--CK 139 139 000 - 185926
|
|---|
| 105 | 194 Temperature_Celsius -O---K 124 099 000 - 26
|
|---|
| 106 | 196 Reallocated_Event_Count -O--CK 165 165 000 - 35
|
|---|
| 107 | 197 Current_Pending_Sector -O--CK 001 001 000 - 65489
|
|---|
| 108 | 198 Offline_Uncorrectable ----CK 200 200 000 - 0
|
|---|
| 109 | 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
|
|---|
| 110 | 200 Multi_Zone_Error_Rate ---R-- 200 195 000 - 0
|
|---|
| 111 | ||||||_ K auto-keep
|
|---|
| 112 | |||||__ C event count
|
|---|
| 113 | ||||___ R error rate
|
|---|
| 114 | |||____ S speed/performance
|
|---|
| 115 | ||_____ O updated online
|
|---|
| 116 | |______ P prefailure warning
|
|---|
| 117 |
|
|---|
| 118 | ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: 48-bit ATA commands not implemented [Prolific]
|
|---|
| 119 | Read GP Log Directory failed
|
|---|
| 120 |
|
|---|
| 121 | SMART Log Directory Version 1 [multi-sector log support]
|
|---|
| 122 | Address Access R/W Size Description
|
|---|
| 123 | 0x00 SL R/O 1 Log Directory
|
|---|
| 124 | 0x01 SL R/O 1 Summary SMART error log
|
|---|
| 125 | 0x02 SL R/O 5 Comprehensive SMART error log
|
|---|
| 126 | 0x06 SL R/O 1 SMART self-test log
|
|---|
| 127 | 0x09 SL R/W 1 Selective self-test log
|
|---|
| 128 | 0x80-0x9f SL R/W 16 Host vendor specific log
|
|---|
| 129 | 0xa0-0xa7 SL VS 16 Device vendor specific log
|
|---|
| 130 | 0xa8-0xb7 SL VS 1 Device vendor specific log
|
|---|
| 131 | 0xc0 SL VS 1 Device vendor specific log
|
|---|
| 132 | 0xe0 SL R/W 1 SCT Command/Status
|
|---|
| 133 | 0xe1 SL R/W 1 SCT Data Transfer
|
|---|
| 134 |
|
|---|
| 135 | SMART Extended Comprehensive Error Log (GP Log 0x03) not supported
|
|---|
| 136 |
|
|---|
| 137 | SMART Error Log Version: 1
|
|---|
| 138 | No Errors Logged
|
|---|
| 139 |
|
|---|
| 140 | SMART Extended Self-test Log (GP Log 0x07) not supported
|
|---|
| 141 |
|
|---|
| 142 | SMART Self-test log structure revision number 1
|
|---|
| 143 | Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
|
|---|
| 144 | # 1 Short offline Completed without error 00% 25151 -
|
|---|
| 145 | # 2 Short offline Completed without error 00% 25148 -
|
|---|
| 146 | # 3 Short offline Completed without error 00% 25148 -
|
|---|
| 147 | # 4 Short offline Aborted by host 90% 25148 -
|
|---|
| 148 | # 5 Short offline Completed without error 00% 25147 -
|
|---|
| 149 | # 6 Short offline Completed without error 00% 25144 -
|
|---|
| 150 | # 7 Short offline Completed without error 00% 25139 -
|
|---|
| 151 | # 8 Extended offline Completed: read failure 90% 25138 553593756
|
|---|
| 152 | # 9 Short offline Completed: read failure 90% 25138 553593752
|
|---|
| 153 | #10 Short offline Completed: read failure 90% 25138 553593756
|
|---|
| 154 | #11 Short offline Completed: read failure 90% 25138 553593752
|
|---|
| 155 | #12 Extended offline Completed without error 00% 23091 -
|
|---|
| 156 | #13 Short offline Completed without error 00% 23084 -
|
|---|
| 157 | #14 Short offline Completed without error 00% 20338 -
|
|---|
| 158 |
|
|---|
| 159 | SMART Selective self-test log data structure revision number 1
|
|---|
| 160 | SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
|
|---|
| 161 | 1 0 0 Not_testing
|
|---|
| 162 | 2 0 0 Not_testing
|
|---|
| 163 | 3 0 0 Not_testing
|
|---|
| 164 | 4 0 0 Not_testing
|
|---|
| 165 | 5 0 0 Not_testing
|
|---|
| 166 | Selective self-test flags (0x0):
|
|---|
| 167 | After scanning selected spans, do NOT read-scan remainder of disk.
|
|---|
| 168 | If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|---|
| 169 |
|
|---|
| 170 | SCT Status Version: 3
|
|---|
| 171 | SCT Version (vendor specific): 258 (0x0102)
|
|---|
| 172 | SCT Support Level: 1
|
|---|
| 173 | Device State: Active (0)
|
|---|
| 174 | Current Temperature: 26 Celsius
|
|---|
| 175 | Power Cycle Min/Max Temperature: 23/26 Celsius
|
|---|
| 176 | Lifetime Min/Max Temperature: 10/51 Celsius
|
|---|
| 177 | Under/Over Temperature Limit Count: 0/0
|
|---|
| 178 |
|
|---|
| 179 | Write SCT Data Table failed: DATA OUT ATA commands not implemented [Prolific]
|
|---|
| 180 | Read SCT Temperature History failed
|
|---|
| 181 |
|
|---|
| 182 | SCT Error Recovery Control command not supported
|
|---|
| 183 |
|
|---|
| 184 | Device Statistics (GP/SMART Log 0x04) not supported
|
|---|
| 185 |
|
|---|
| 186 | ATA_READ_LOG_EXT (addr=0x11:0x00, page=0, n=1) failed: 48-bit ATA commands not implemented [Prolific]
|
|---|
| 187 | Read SATA Phy Event Counters failed
|
|---|
| 188 |
|
|---|
| 189 | XXX@XXX:~/devel/smartmontools$ sudo ./smartctl -t short /dev/sdb
|
|---|
| 190 | smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.13.0-39-generic] (local build)
|
|---|
| 191 | Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
|
|---|
| 192 |
|
|---|
| 193 | === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
|
|---|
| 194 | Sending command: "Execute SMART Short self-test routine immediately in off-line mode".
|
|---|
| 195 | Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful.
|
|---|
| 196 | Testing has begun.
|
|---|
| 197 | Please wait 2 minutes for test to complete.
|
|---|
| 198 | Test will complete after Tue Nov 4 20:35:30 2014
|
|---|
| 199 |
|
|---|
| 200 | Use smartctl -X to abort test.
|
|---|
| 201 |
|
|---|
| 202 |
|
|---|
| 203 |
|
|---|
