| 1 | smartctl pre-7.4 2022-12-05 r5422 [x86_64-linux-3.10.0-1160.el7.x86_64] (CircleCI)
|
|---|
| 2 | Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
|
|---|
| 3 |
|
|---|
| 4 | === START OF INFORMATION SECTION ===
|
|---|
| 5 | Vendor: TOSHIBA
|
|---|
| 6 | Product: AL15SEB060N
|
|---|
| 7 | Revision: 3101
|
|---|
| 8 | Compliance: SPC-4
|
|---|
| 9 | User Capacity: 600,127,266,816 bytes [600 GB]
|
|---|
| 10 | Logical block size: 512 bytes
|
|---|
| 11 | Rotation Rate: 10500 rpm
|
|---|
| 12 | Form Factor: 2.5 inches
|
|---|
| 13 | Logical Unit id: 0x5000039b48736e9d
|
|---|
| 14 | Serial number: Y1Q0A02KFYVH
|
|---|
| 15 | Device type: disk
|
|---|
| 16 | Transport protocol: SAS (SPL-4)
|
|---|
| 17 | Local Time is: Wed Dec 7 09:37:12 2022 CST
|
|---|
| 18 | SMART support is: Available - device has SMART capability.
|
|---|
| 19 | SMART support is: Enabled
|
|---|
| 20 | Temperature Warning: Enabled
|
|---|
| 21 | Read Cache is: Enabled
|
|---|
| 22 | Writeback Cache is: Enabled
|
|---|
| 23 |
|
|---|
| 24 | === START OF READ SMART DATA SECTION ===
|
|---|
| 25 | SMART Health Status: OK
|
|---|
| 26 |
|
|---|
| 27 | Current Drive Temperature: 38 C
|
|---|
| 28 | Drive Trip Temperature: 65 C
|
|---|
| 29 |
|
|---|
| 30 | Manufactured in week 47 of year 2021
|
|---|
| 31 | Specified cycle count over device lifetime: 50000
|
|---|
| 32 | Accumulated start-stop cycles: 59
|
|---|
| 33 | Specified load-unload count over device lifetime: 600000
|
|---|
| 34 | Accumulated load-unload cycles: 5406
|
|---|
| 35 | Elements in grown defect list: 0
|
|---|
| 36 |
|
|---|
| 37 | Error counter log:
|
|---|
| 38 | Errors Corrected by Total Correction Gigabytes Total
|
|---|
| 39 | ECC rereads/ errors algorithm processed uncorrected
|
|---|
| 40 | fast | delayed rewrites corrected invocations [10^9 bytes] errors
|
|---|
| 41 | read: 221452 0 0 0 0 118978.756 0
|
|---|
| 42 | write: 0 0 0 0 0 203.179 0
|
|---|
| 43 | verify: 0 0 0 0 0 11.060 0
|
|---|
| 44 |
|
|---|
| 45 | Non-medium error count: 33
|
|---|
| 46 |
|
|---|
| 47 | SMART Self-test log
|
|---|
| 48 | Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
|
|---|
| 49 | Description number (hours)
|
|---|
| 50 | # 1 Background long Completed - 5 - [- - -]
|
|---|
| 51 | # 2 Background short Completed - 4 - [- - -]
|
|---|
| 52 |
|
|---|
| 53 | Long (extended) Self-test duration: 3917 seconds [65.3 minutes]
|
|---|
| 54 |
|
|---|
| 55 | Background scan results log
|
|---|
| 56 | Status: waiting until BMS interval timer expires
|
|---|
| 57 | Accumulated power on time, hours:minutes 4329:31 [259771 minutes]
|
|---|
| 58 | Number of background scans performed: 196, scan progress: 0.00%
|
|---|
| 59 | Number of background medium scans performed: 0
|
|---|
| 60 |
|
|---|
| 61 | # when lba(hex) [sk,asc,ascq] reassign_status
|
|---|
| 62 | 1 265:20 0000000000275eb5 [1,18,7] Recovered via rewrite in-place
|
|---|
| 63 | 2 433:21 0000000000bd42ca [1,18,7] Recovered via rewrite in-place
|
|---|
| 64 | 3 721:31 0000000001566195 [1,18,7] Recovered via rewrite in-place
|
|---|
| 65 | 4 1542:00 00000000000a8593 [1,18,7] Recovered via rewrite in-place
|
|---|
| 66 | 5 2251:44 00000000000a858d [1,18,7] Recovered via rewrite in-place
|
|---|
| 67 | 6 3185:00 0000000000bd42c8 [1,18,7] Recovered via rewrite in-place
|
|---|
| 68 |
|
|---|
| 69 |
|
|---|
| 70 | Protocol Specific port log page for SAS SSP
|
|---|
| 71 | relative target port id = 1
|
|---|
| 72 | generation code = 2
|
|---|
| 73 | number of phys = 1
|
|---|
| 74 | phy identifier = 0
|
|---|
| 75 | attached device type: SAS or SATA device
|
|---|
| 76 | attached reason: power on
|
|---|
| 77 | reason: loss of dword synchronization
|
|---|
| 78 | negotiated logical link rate: phy enabled; 12 Gbps
|
|---|
| 79 | attached initiator port: ssp=1 stp=1 smp=1
|
|---|
| 80 | attached target port: ssp=0 stp=0 smp=0
|
|---|
| 81 | SAS address = 0x5000039b48736e9e
|
|---|
| 82 | attached SAS address = 0x5d8ffc3000000000
|
|---|
| 83 | attached phy identifier = 3
|
|---|
| 84 | Invalid DWORD count = 16
|
|---|
| 85 | Running disparity error count = 16
|
|---|
| 86 | Loss of DWORD synchronization count = 4
|
|---|
| 87 | Phy reset problem count = 0
|
|---|
| 88 | Phy event descriptors:
|
|---|
| 89 | Elasticity buffer overflow count: 0
|
|---|
| 90 | Received abandon-class OPEN_REJECT count: 0
|
|---|
| 91 | Transmitted BREAK count: 0
|
|---|
| 92 | Received BREAK count: 0
|
|---|
| 93 | Transmitted SSP frame error count: 0
|
|---|
| 94 | Received SSP frame error count: 0
|
|---|
| 95 | relative target port id = 2
|
|---|
| 96 | generation code = 2
|
|---|
| 97 | number of phys = 1
|
|---|
| 98 | phy identifier = 1
|
|---|
| 99 | attached device type: no device attached
|
|---|
| 100 | attached reason: unknown
|
|---|
| 101 | reason: unknown
|
|---|
| 102 | negotiated logical link rate: phy enabled; unknown
|
|---|
| 103 | attached initiator port: ssp=0 stp=0 smp=0
|
|---|
| 104 | attached target port: ssp=0 stp=0 smp=0
|
|---|
| 105 | SAS address = 0x5000039b48736e9f
|
|---|
| 106 | attached SAS address = 0x0
|
|---|
| 107 | attached phy identifier = 0
|
|---|
| 108 | Invalid DWORD count = 0
|
|---|
| 109 | Running disparity error count = 0
|
|---|
| 110 | Loss of DWORD synchronization count = 0
|
|---|
| 111 | Phy reset problem count = 0
|
|---|
| 112 | Phy event descriptors:
|
|---|
| 113 | Elasticity buffer overflow count: 0
|
|---|
| 114 | Received abandon-class OPEN_REJECT count: 0
|
|---|
| 115 | Transmitted BREAK count: 0
|
|---|
| 116 | Received BREAK count: 0
|
|---|
| 117 | Transmitted SSP frame error count: 0
|
|---|
| 118 | Received SSP frame error count: 0
|
|---|
| 119 |
|
|---|
