| 1 | smartctl 7.3 2022-02-28 r5338 [i686-w64-mingw32-win7-sp1(64)] (sf-7.3-1)
|
|---|
| 2 | Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
|
|---|
| 3 |
|
|---|
| 4 | === START OF INFORMATION SECTION ===
|
|---|
| 5 | Device Model: #DI LCB0D #DFULCB0D0033
|
|---|
| 6 | Serial Number: 75UECBGIT
|
|---|
| 7 | LU WWN Device Id: 5 000039 66398a103
|
|---|
| 8 | Firmware Version: AM001K
|
|---|
| 9 | User Capacity: 320,072,933,376 bytes [320 GB]
|
|---|
| 10 | Sector Sizes: 512 bytes logical, 4096 bytes physical
|
|---|
| 11 | Rotation Rate: 5400 rpm
|
|---|
| 12 | Form Factor: 2.5 inches
|
|---|
| 13 | Device is: Not in smartctl database 7.3/5319
|
|---|
| 14 | ATA Version is: ATA8-ACS (minor revision not indicated)
|
|---|
| 15 | SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
|
|---|
| 16 | Local Time is: Thu Jul 21 12:14:43 2022 CDT
|
|---|
| 17 | SMART support is: Available - device has SMART capability.
|
|---|
| 18 | SMART support is: Enabled
|
|---|
| 19 |
|
|---|
| 20 | === START OF READ SMART DATA SECTION ===
|
|---|
| 21 | SMART overall-health self-assessment test result: PASSED
|
|---|
| 22 |
|
|---|
| 23 | General SMART Values:
|
|---|
| 24 | Offline data collection status: (0x00) Offline data collection activity
|
|---|
| 25 | was never started.
|
|---|
| 26 | Auto Offline Data Collection: Disabled.
|
|---|
| 27 | Self-test execution status: ( 0) The previous self-test routine completed
|
|---|
| 28 | without error or no self-test has ever
|
|---|
| 29 | been run.
|
|---|
| 30 | Total time to complete Offline
|
|---|
| 31 | data collection: ( 120) seconds.
|
|---|
| 32 | Offline data collection
|
|---|
| 33 | capabilities: (0x5b) SMART execute Offline immediate.
|
|---|
| 34 | Auto Offline data collection on/off support.
|
|---|
| 35 | Suspend Offline collection upon new
|
|---|
| 36 | command.
|
|---|
| 37 | Offline surface scan supported.
|
|---|
| 38 | Self-test supported.
|
|---|
| 39 | No Conveyance Self-test supported.
|
|---|
| 40 | Selective Self-test supported.
|
|---|
| 41 | SMART capabilities: (0x0003) Saves SMART data before entering
|
|---|
| 42 | power-saving mode.
|
|---|
| 43 | Supports SMART auto save timer.
|
|---|
| 44 | Error logging capability: (0x01) Error logging supported.
|
|---|
| 45 | General Purpose Logging supported.
|
|---|
| 46 | Short self-test routine
|
|---|
| 47 | recommended polling time: ( 2) minutes.
|
|---|
| 48 | Extended self-test routine
|
|---|
| 49 | recommended polling time: ( 69) minutes.
|
|---|
| 50 | SCT capabilities: (0x003d) SCT Status supported.
|
|---|
| 51 | SCT Error Recovery Control supported.
|
|---|
| 52 | SCT Feature Control supported.
|
|---|
| 53 | SCT Data Table supported.
|
|---|
| 54 |
|
|---|
| 55 | SMART Attributes Data Structure revision number: 16
|
|---|
| 56 | Vendor Specific SMART Attributes with Thresholds:
|
|---|
| 57 | ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
|
|---|
| 58 | 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
|
|---|
| 59 | 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
|
|---|
| 60 | 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1356
|
|---|
| 61 | 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 1292
|
|---|
| 62 | 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
|
|---|
| 63 | 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
|
|---|
| 64 | 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
|
|---|
| 65 | 9 Power_On_Hours 0x0032 071 071 000 Old_age Always - 11942
|
|---|
| 66 | 10 Spin_Retry_Count 0x0033 125 100 030 Pre-fail Always - 0
|
|---|
| 67 | 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1283
|
|---|
| 68 | 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 17
|
|---|
| 69 | 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 66
|
|---|
| 70 | 193 Load_Cycle_Count 0x0032 090 090 000 Old_age Always - 105549
|
|---|
| 71 | 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 36 (Min/Max 12/49)
|
|---|
| 72 | 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
|
|---|
| 73 | 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
|
|---|
| 74 | 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
|
|---|
| 75 | 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
|
|---|
| 76 | 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
|
|---|
| 77 | 222 Loaded_Hours 0x0032 071 071 000 Old_age Always - 11853
|
|---|
| 78 | 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
|
|---|
| 79 | 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
|
|---|
| 80 | 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 247
|
|---|
| 81 | 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
|
|---|
| 82 |
|
|---|
| 83 | SMART Error Log Version: 1
|
|---|
| 84 | ATA Error Count: 283 (device log contains only the most recent five errors)
|
|---|
| 85 | CR = Command Register [HEX]
|
|---|
| 86 | FR = Features Register [HEX]
|
|---|
| 87 | SC = Sector Count Register [HEX]
|
|---|
| 88 | SN = Sector Number Register [HEX]
|
|---|
| 89 | CL = Cylinder Low Register [HEX]
|
|---|
| 90 | CH = Cylinder High Register [HEX]
|
|---|
| 91 | DH = Device/Head Register [HEX]
|
|---|
| 92 | DC = Device Command Register [HEX]
|
|---|
| 93 | ER = Error register [HEX]
|
|---|
| 94 | ST = Status register [HEX]
|
|---|
| 95 | Powered_Up_Time is measured from power on, and printed as
|
|---|
| 96 | DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
|
|---|
| 97 | SS=sec, and sss=millisec. It "wraps" after 49.710 days.
|
|---|
| 98 |
|
|---|
| 99 | Error 283 occurred at disk power-on lifetime: 9243 hours (385 days + 3 hours)
|
|---|
| 100 | When the command that caused the error occurred, the device was active or idle.
|
|---|
| 101 |
|
|---|
| 102 | After command completion occurred, registers were:
|
|---|
| 103 | ER ST SC SN CL CH DH
|
|---|
| 104 | -- -- -- -- -- -- --
|
|---|
| 105 | 40 41 00 70 8e f3 40 Error: WP at LBA = 0x00f38e70 = 15961712
|
|---|
| 106 |
|
|---|
| 107 | Commands leading to the command that caused the error were:
|
|---|
| 108 | CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|---|
| 109 | -- -- -- -- -- -- -- -- ---------------- --------------------
|
|---|
| 110 | 61 48 70 50 c5 03 40 00 07:34:10.367 WRITE FPDMA QUEUED
|
|---|
| 111 | 61 00 68 b8 a0 f5 40 00 07:34:10.367 WRITE FPDMA QUEUED
|
|---|
| 112 | 61 00 60 b8 9f f5 40 00 07:34:10.367 WRITE FPDMA QUEUED
|
|---|
| 113 | 61 00 58 b8 9e f5 40 00 07:34:10.367 WRITE FPDMA QUEUED
|
|---|
| 114 | 61 00 50 b8 9d f5 40 00 07:34:10.367 WRITE FPDMA QUEUED
|
|---|
| 115 |
|
|---|
| 116 | Error 282 occurred at disk power-on lifetime: 9243 hours (385 days + 3 hours)
|
|---|
| 117 | When the command that caused the error occurred, the device was active or idle.
|
|---|
| 118 |
|
|---|
| 119 | After command completion occurred, registers were:
|
|---|
| 120 | ER ST SC SN CL CH DH
|
|---|
| 121 | -- -- -- -- -- -- --
|
|---|
| 122 | 40 41 00 70 8e f3 40 Error: WP at LBA = 0x00f38e70 = 15961712
|
|---|
| 123 |
|
|---|
| 124 | Commands leading to the command that caused the error were:
|
|---|
| 125 | CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|---|
| 126 | -- -- -- -- -- -- -- -- ---------------- --------------------
|
|---|
| 127 | 61 08 20 a0 30 03 40 00 07:33:10.091 WRITE FPDMA QUEUED
|
|---|
| 128 | 61 08 30 80 92 05 40 00 07:33:09.640 WRITE FPDMA QUEUED
|
|---|
| 129 | 61 08 20 f0 8a 10 40 00 07:33:09.639 WRITE FPDMA QUEUED
|
|---|
| 130 | 61 08 28 90 0f 08 40 00 07:33:09.639 WRITE FPDMA QUEUED
|
|---|
| 131 | 61 08 20 b8 51 05 40 00 07:33:09.639 WRITE FPDMA QUEUED
|
|---|
| 132 |
|
|---|
| 133 | Error 281 occurred at disk power-on lifetime: 9243 hours (385 days + 3 hours)
|
|---|
| 134 | When the command that caused the error occurred, the device was active or idle.
|
|---|
| 135 |
|
|---|
| 136 | After command completion occurred, registers were:
|
|---|
| 137 | ER ST SC SN CL CH DH
|
|---|
| 138 | -- -- -- -- -- -- --
|
|---|
| 139 | 40 41 40 70 8e f3 40 Error: UNC at LBA = 0x00f38e70 = 15961712
|
|---|
| 140 |
|
|---|
| 141 | Commands leading to the command that caused the error were:
|
|---|
| 142 | CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|---|
| 143 | -- -- -- -- -- -- -- -- ---------------- --------------------
|
|---|
| 144 | 60 08 28 30 6c ee 40 00 07:33:00.270 READ FPDMA QUEUED
|
|---|
| 145 | 60 20 08 69 75 16 40 00 07:33:00.270 READ FPDMA QUEUED
|
|---|
| 146 | 61 00 00 40 44 05 40 00 07:32:59.952 WRITE FPDMA QUEUED
|
|---|
| 147 | 61 00 f8 40 45 05 40 00 07:32:59.952 WRITE FPDMA QUEUED
|
|---|
| 148 | 61 00 f0 40 46 05 40 00 07:32:59.952 WRITE FPDMA QUEUED
|
|---|
| 149 |
|
|---|
| 150 | Error 280 occurred at disk power-on lifetime: 9243 hours (385 days + 3 hours)
|
|---|
| 151 | When the command that caused the error occurred, the device was active or idle.
|
|---|
| 152 |
|
|---|
| 153 | After command completion occurred, registers were:
|
|---|
| 154 | ER ST SC SN CL CH DH
|
|---|
| 155 | -- -- -- -- -- -- --
|
|---|
| 156 | 40 41 00 70 8e f3 40 Error: WP at LBA = 0x00f38e70 = 15961712
|
|---|
| 157 |
|
|---|
| 158 | Commands leading to the command that caused the error were:
|
|---|
| 159 | CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|---|
| 160 | -- -- -- -- -- -- -- -- ---------------- --------------------
|
|---|
| 161 | 61 08 10 58 69 05 40 00 07:30:33.356 WRITE FPDMA QUEUED
|
|---|
| 162 | 61 08 10 88 30 03 40 00 07:30:33.138 WRITE FPDMA QUEUED
|
|---|
| 163 | 61 08 10 a0 30 03 40 00 07:30:33.138 WRITE FPDMA QUEUED
|
|---|
| 164 | 61 20 10 60 c3 03 40 00 07:30:33.137 WRITE FPDMA QUEUED
|
|---|
| 165 | 60 20 08 69 75 16 40 00 07:30:32.933 READ FPDMA QUEUED
|
|---|
| 166 |
|
|---|
| 167 | Error 279 occurred at disk power-on lifetime: 9243 hours (385 days + 3 hours)
|
|---|
| 168 | When the command that caused the error occurred, the device was active or idle.
|
|---|
| 169 |
|
|---|
| 170 | After command completion occurred, registers were:
|
|---|
| 171 | ER ST SC SN CL CH DH
|
|---|
| 172 | -- -- -- -- -- -- --
|
|---|
| 173 | 40 41 00 70 8e f3 40 Error: WP at LBA = 0x00f38e70 = 15961712
|
|---|
| 174 |
|
|---|
| 175 | Commands leading to the command that caused the error were:
|
|---|
| 176 | CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|---|
| 177 | -- -- -- -- -- -- -- -- ---------------- --------------------
|
|---|
| 178 | 61 08 08 98 30 03 40 00 07:30:15.573 WRITE FPDMA QUEUED
|
|---|
| 179 | 61 20 08 d8 c2 03 40 00 07:30:15.573 WRITE FPDMA QUEUED
|
|---|
| 180 | 61 00 40 00 ec fc 40 00 07:30:15.435 WRITE FPDMA QUEUED
|
|---|
| 181 | 61 00 38 00 eb fc 40 00 07:30:15.435 WRITE FPDMA QUEUED
|
|---|
| 182 | 61 00 30 00 ea fc 40 00 07:30:15.435 WRITE FPDMA QUEUED
|
|---|
| 183 |
|
|---|
| 184 | SMART Self-test log structure revision number 1
|
|---|
| 185 | No self-tests have been logged. [To run self-tests, use: smartctl -t]
|
|---|
| 186 |
|
|---|
| 187 | SMART Selective self-test log data structure revision number 1
|
|---|
| 188 | SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
|
|---|
| 189 | 1 0 0 Not_testing
|
|---|
| 190 | 2 0 0 Not_testing
|
|---|
| 191 | 3 0 0 Not_testing
|
|---|
| 192 | 4 0 0 Not_testing
|
|---|
| 193 | 5 0 0 Not_testing
|
|---|
| 194 | Selective self-test flags (0x0):
|
|---|
| 195 | After scanning selected spans, do NOT read-scan remainder of disk.
|
|---|
| 196 | If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|---|
| 197 |
|
|---|
