1 | smartctl 7.2 2020-09-19 r5083 [x86_64-linux-5.8.18-Unraid] (local build) |
---|
2 | Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org |
---|
3 | |
---|
4 | === START OF INFORMATION SECTION === |
---|
5 | Model Family: Seagate Samsung SpinPoint M8 (AF) |
---|
6 | Device Model: ST1000LM024 HN-M101MBB |
---|
7 | Firmware Version: 2BA30001 |
---|
8 | User Capacity: 1,000,204,886,016 bytes [1.00 TB] |
---|
9 | Sector Sizes: 512 bytes logical, 4096 bytes physical |
---|
10 | Rotation Rate: 5400 rpm |
---|
11 | Form Factor: 2.5 inches |
---|
12 | Device is: In smartctl database [for details use: -P show] |
---|
13 | ATA Version is: ATA8-ACS T13/1699-D revision 6 |
---|
14 | SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) |
---|
15 | Local Time is: Fri Dec 11 11:26:23 2020 GMT |
---|
16 | SMART support is: Available - device has SMART capability. |
---|
17 | SMART support is: Enabled |
---|
18 | AAM feature is: Disabled |
---|
19 | APM feature is: Disabled |
---|
20 | Rd look-ahead is: Enabled |
---|
21 | Write cache is: Enabled |
---|
22 | DSN feature is: Unavailable |
---|
23 | ATA Security is: Disabled, NOT FROZEN [SEC1] |
---|
24 | Wt Cache Reorder: Unknown |
---|
25 | |
---|
26 | === START OF READ SMART DATA SECTION === |
---|
27 | SMART Status not supported: Incomplete response, ATA output registers missing |
---|
28 | SMART overall-health self-assessment test result: PASSED |
---|
29 | Warning: This result is based on an Attribute check. |
---|
30 | |
---|
31 | General SMART Values: |
---|
32 | Offline data collection status: (0x00) Offline data collection activity |
---|
33 | was never started. |
---|
34 | Auto Offline Data Collection: Disabled. |
---|
35 | Self-test execution status: ( 0) The previous self-test routine completed |
---|
36 | without error or no self-test has ever |
---|
37 | been run. |
---|
38 | Total time to complete Offline |
---|
39 | data collection: (13740) seconds. |
---|
40 | Offline data collection |
---|
41 | capabilities: (0x5b) SMART execute Offline immediate. |
---|
42 | Auto Offline data collection on/off support. |
---|
43 | Suspend Offline collection upon new |
---|
44 | command. |
---|
45 | Offline surface scan supported. |
---|
46 | Self-test supported. |
---|
47 | No Conveyance Self-test supported. |
---|
48 | Selective Self-test supported. |
---|
49 | SMART capabilities: (0x0003) Saves SMART data before entering |
---|
50 | power-saving mode. |
---|
51 | Supports SMART auto save timer. |
---|
52 | Error logging capability: (0x01) Error logging supported. |
---|
53 | General Purpose Logging supported. |
---|
54 | Short self-test routine |
---|
55 | recommended polling time: ( 2) minutes. |
---|
56 | Extended self-test routine |
---|
57 | recommended polling time: ( 229) minutes. |
---|
58 | SCT capabilities: (0x003f) SCT Status supported. |
---|
59 | SCT Error Recovery Control supported. |
---|
60 | SCT Feature Control supported. |
---|
61 | SCT Data Table supported. |
---|
62 | |
---|
63 | SMART Attributes Data Structure revision number: 16 |
---|
64 | Vendor Specific SMART Attributes with Thresholds: |
---|
65 | ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE |
---|
66 | 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 3 |
---|
67 | 2 Throughput_Performance -OS--K 252 252 000 - 0 |
---|
68 | 3 Spin_Up_Time PO---K 090 089 025 - 3300 |
---|
69 | 4 Start_Stop_Count -O--CK 098 098 000 - 2460 |
---|
70 | 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 |
---|
71 | 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 |
---|
72 | 8 Seek_Time_Performance --S--K 252 252 015 - 0 |
---|
73 | 9 Power_On_Hours -O--CK 100 100 000 - 13284 |
---|
74 | 10 Spin_Retry_Count -O--CK 252 252 051 - 0 |
---|
75 | 11 Calibration_Retry_Count -O--CK 100 100 000 - 59 |
---|
76 | 12 Power_Cycle_Count -O--CK 097 097 000 - 3517 |
---|
77 | 191 G-Sense_Error_Rate -O---K 100 100 000 - 2 |
---|
78 | 192 Power-Off_Retract_Count -O---K 100 100 000 - 1001 |
---|
79 | 194 Temperature_Celsius -O---- 064 057 000 - 30 (Min/Max 18/49) |
---|
80 | 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 |
---|
81 | 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 |
---|
82 | 197 Current_Pending_Sector -O--CK 252 252 000 - 0 |
---|
83 | 198 Offline_Uncorrectable ----CK 252 252 000 - 0 |
---|
84 | 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 |
---|
85 | 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 120 |
---|
86 | 223 Load_Retry_Count -O--CK 100 100 000 - 59 |
---|
87 | 225 Load_Cycle_Count -O--CK 078 078 000 - 227938 |
---|
88 | ||||||_ K auto-keep |
---|
89 | |||||__ C event count |
---|
90 | ||||___ R error rate |
---|
91 | |||____ S speed/performance |
---|
92 | ||_____ O updated online |
---|
93 | |______ P prefailure warning |
---|
94 | |
---|
95 | General Purpose Log Directory Version 1 |
---|
96 | SMART Log Directory Version 1 [multi-sector log support] |
---|
97 | Address Access R/W Size Description |
---|
98 | 0x00 GPL,SL R/O 1 Log Directory |
---|
99 | 0x01 SL R/O 1 Summary SMART error log |
---|
100 | 0x02 SL R/O 2 Comprehensive SMART error log |
---|
101 | 0x03 GPL R/O 2 Ext. Comprehensive SMART error log |
---|
102 | 0x06 SL R/O 1 SMART self-test log |
---|
103 | 0x07 GPL R/O 2 Extended self-test log |
---|
104 | 0x08 GPL R/O 2 Power Conditions log |
---|
105 | 0x09 SL R/W 1 Selective self-test log |
---|
106 | 0x10 GPL R/O 1 NCQ Command Error log |
---|
107 | 0x11 GPL R/O 1 SATA Phy Event Counters log |
---|
108 | 0x80-0x9f GPL,SL R/W 16 Host vendor specific log |
---|
109 | 0xc0-0xdf GPL,SL VS 16 Device vendor specific log |
---|
110 | 0xe0 GPL,SL R/W 1 SCT Command/Status |
---|
111 | 0xe1 GPL,SL R/W 1 SCT Data Transfer |
---|
112 | |
---|
113 | SMART Extended Comprehensive Error Log Version: 1 (2 sectors) |
---|
114 | No Errors Logged |
---|
115 | |
---|
116 | SMART Extended Self-test Log Version: 1 (2 sectors) |
---|
117 | Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error |
---|
118 | # 1 Short offline Completed without error 00% 13283 - |
---|
119 | # 2 Short offline Completed without error 00% 13073 - |
---|
120 | |
---|
121 | SMART Selective self-test log data structure revision number 0 |
---|
122 | Note: revision number not 1 implies that no selective self-test has ever been run |
---|
123 | SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS |
---|
124 | 1 0 0 Completed [00% left] (0-65535) |
---|
125 | 2 0 0 Not_testing |
---|
126 | 3 0 0 Not_testing |
---|
127 | 4 0 0 Not_testing |
---|
128 | 5 0 0 Not_testing |
---|
129 | Selective self-test flags (0x0): |
---|
130 | After scanning selected spans, do NOT read-scan remainder of disk. |
---|
131 | If Selective self-test is pending on power-up, resume after 0 minute delay. |
---|
132 | |
---|
133 | SCT Status Version: 2 |
---|
134 | SCT Version (vendor specific): 256 (0x0100) |
---|
135 | Device State: Active (0) |
---|
136 | Current Temperature: 30 Celsius |
---|
137 | Power Cycle Min/Max Temperature: 28/30 Celsius |
---|
138 | Lifetime Min/Max Temperature: 18/49 Celsius |
---|
139 | Specified Max Operating Temperature: 80 Celsius |
---|
140 | Under/Over Temperature Limit Count: 0/0 |
---|
141 | |
---|
142 | SCT Temperature History Version: 2 |
---|
143 | Temperature Sampling Period: 5 minutes |
---|
144 | Temperature Logging Interval: 5 minutes |
---|
145 | Min/Max recommended Temperature: -5/80 Celsius |
---|
146 | Min/Max Temperature Limit: -10/85 Celsius |
---|
147 | Temperature History Size (Index): 128 (90) |
---|
148 | |
---|
149 | Index Estimated Time Temperature Celsius |
---|
150 | 91 2020-12-11 00:50 30 *********** |
---|
151 | ... ..( 2 skipped). .. *********** |
---|
152 | 94 2020-12-11 01:05 30 *********** |
---|
153 | 95 2020-12-11 01:10 29 ********** |
---|
154 | 96 2020-12-11 01:15 30 *********** |
---|
155 | ... ..( 2 skipped). .. *********** |
---|
156 | 99 2020-12-11 01:30 30 *********** |
---|
157 | 100 2020-12-11 01:35 29 ********** |
---|
158 | 101 2020-12-11 01:40 30 *********** |
---|
159 | ... ..( 9 skipped). .. *********** |
---|
160 | 111 2020-12-11 02:30 30 *********** |
---|
161 | 112 2020-12-11 02:35 31 ************ |
---|
162 | ... ..( 7 skipped). .. ************ |
---|
163 | 120 2020-12-11 03:15 31 ************ |
---|
164 | 121 2020-12-11 03:20 30 *********** |
---|
165 | ... ..( 15 skipped). .. *********** |
---|
166 | 9 2020-12-11 04:40 30 *********** |
---|
167 | 10 2020-12-11 04:45 29 ********** |
---|
168 | ... ..( 2 skipped). .. ********** |
---|
169 | 13 2020-12-11 05:00 29 ********** |
---|
170 | 14 2020-12-11 05:05 30 *********** |
---|
171 | ... ..( 32 skipped). .. *********** |
---|
172 | 47 2020-12-11 07:50 30 *********** |
---|
173 | 48 2020-12-11 07:55 31 ************ |
---|
174 | ... ..( 3 skipped). .. ************ |
---|
175 | 52 2020-12-11 08:15 31 ************ |
---|
176 | 53 2020-12-11 08:20 30 *********** |
---|
177 | ... ..( 5 skipped). .. *********** |
---|
178 | 59 2020-12-11 08:50 30 *********** |
---|
179 | 60 2020-12-11 08:55 29 ********** |
---|
180 | 61 2020-12-11 09:00 29 ********** |
---|
181 | 62 2020-12-11 09:05 30 *********** |
---|
182 | 63 2020-12-11 09:10 27 ******** |
---|
183 | 64 2020-12-11 09:15 28 ********* |
---|
184 | 65 2020-12-11 09:20 29 ********** |
---|
185 | 66 2020-12-11 09:25 29 ********** |
---|
186 | 67 2020-12-11 09:30 30 *********** |
---|
187 | 68 2020-12-11 09:35 27 ******** |
---|
188 | 69 2020-12-11 09:40 29 ********** |
---|
189 | 70 2020-12-11 09:45 30 *********** |
---|
190 | ... ..( 10 skipped). .. *********** |
---|
191 | 81 2020-12-11 10:40 30 *********** |
---|
192 | 82 2020-12-11 10:45 29 ********** |
---|
193 | 83 2020-12-11 10:50 29 ********** |
---|
194 | 84 2020-12-11 10:55 30 *********** |
---|
195 | 85 2020-12-11 11:00 27 ******** |
---|
196 | 86 2020-12-11 11:05 29 ********** |
---|
197 | 87 2020-12-11 11:10 30 *********** |
---|
198 | 88 2020-12-11 11:15 30 *********** |
---|
199 | 89 2020-12-11 11:20 31 ************ |
---|
200 | 90 2020-12-11 11:25 30 *********** |
---|
201 | |
---|
202 | SMART WRITE LOG does not return COUNT and LBA_LOW register |
---|
203 | SCT (Get) Error Recovery Control command failed |
---|
204 | |
---|
205 | Device Statistics (GP/SMART Log 0x04) not supported |
---|
206 | |
---|
207 | Pending Defects log (GP Log 0x0c) not supported |
---|
208 | |
---|
209 | SATA Phy Event Counters (GP Log 0x11) |
---|
210 | ID Size Value Description |
---|
211 | 0x0001 4 0 Command failed due to ICRC error |
---|
212 | 0x0002 4 0 R_ERR response for data FIS |
---|
213 | 0x0003 4 0 R_ERR response for device-to-host data FIS |
---|
214 | 0x0004 4 0 R_ERR response for host-to-device data FIS |
---|
215 | 0x0005 4 0 R_ERR response for non-data FIS |
---|
216 | 0x0006 4 0 R_ERR response for device-to-host non-data FIS |
---|
217 | 0x0007 4 0 R_ERR response for host-to-device non-data FIS |
---|
218 | 0x0008 4 0 Device-to-host non-data FIS retries |
---|
219 | 0x0009 4 1 Transition from drive PhyRdy to drive PhyNRdy |
---|
220 | 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET |
---|
221 | 0x000b 4 0 CRC errors within host-to-device FIS |
---|
222 | 0x000d 4 0 Non-CRC errors within host-to-device FIS |
---|
223 | 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC |
---|
224 | 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC |
---|
225 | 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC |
---|
226 | 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC |
---|
227 | 0x8e00 4 0 Vendor specific |
---|
228 | 0x8e01 4 0 Vendor specific |
---|
229 | 0x8e02 4 0 Vendor specific |
---|
230 | 0x8e03 4 0 Vendor specific |
---|
231 | 0x8e04 4 0 Vendor specific |
---|
232 | 0x8e05 4 0 Vendor specific |
---|
233 | 0x8e06 4 0 Vendor specific |
---|
234 | 0x8e07 4 0 Vendor specific |
---|
235 | 0x8e08 4 0 Vendor specific |
---|
236 | 0x8e09 4 0 Vendor specific |
---|
237 | 0x8e0a 4 0 Vendor specific |
---|
238 | 0x8e0b 4 0 Vendor specific |
---|
239 | 0x8e0c 4 0 Vendor specific |
---|
240 | 0x8e0d 4 0 Vendor specific |
---|
241 | 0x8e0e 4 0 Vendor specific |
---|
242 | 0x8e0f 4 0 Vendor specific |
---|
243 | 0x8e10 4 0 Vendor specific |
---|
244 | 0x8e11 4 0 Vendor specific |
---|
245 | |
---|