| 1 | ATA device, with non-removable media
|
|---|
| 2 | Model Number: WDC WD40EFRX-68N32N0
|
|---|
| 3 | Serial Number: <exists :)>
|
|---|
| 4 | Firmware Revision: 82.00A82
|
|---|
| 5 | Transport: Serial, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
|
|---|
| 6 | Standards:
|
|---|
| 7 | Used: unknown (minor revision code 0x006d)
|
|---|
| 8 | Supported: 10 9 8 7 6 5
|
|---|
| 9 | Likely used: 10
|
|---|
| 10 | Configuration:
|
|---|
| 11 | Logical max current
|
|---|
| 12 | cylinders 16383 0
|
|---|
| 13 | heads 16 0
|
|---|
| 14 | sectors/track 63 0
|
|---|
| 15 | --
|
|---|
| 16 | LBA user addressable sectors: 268435455
|
|---|
| 17 | LBA48 user addressable sectors: 7814037168
|
|---|
| 18 | Logical Sector size: 512 bytes
|
|---|
| 19 | Physical Sector size: 4096 bytes
|
|---|
| 20 | Logical Sector-0 offset: 0 bytes
|
|---|
| 21 | device size with M = 1024*1024: 3815447 MBytes
|
|---|
| 22 | device size with M = 1000*1000: 4000787 MBytes (4000 GB)
|
|---|
| 23 | cache/buffer size = unknown
|
|---|
| 24 | Form Factor: 3.5 inch
|
|---|
| 25 | Nominal Media Rotation Rate: 5400
|
|---|
| 26 | Capabilities:
|
|---|
| 27 | LBA, IORDY(can be disabled)
|
|---|
| 28 | Queue depth: 32
|
|---|
| 29 | Standby timer values: spec'd by Standard, with device specific minimum
|
|---|
| 30 | R/W multiple sector transfer: Max = 16 Current = 16
|
|---|
| 31 | DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
|
|---|
| 32 | Cycle time: min=120ns recommended=120ns
|
|---|
| 33 | PIO: pio0 pio1 pio2 pio3 pio4
|
|---|
| 34 | Cycle time: no flow control=120ns IORDY flow control=120ns
|
|---|
| 35 | Commands/features:
|
|---|
| 36 | Enabled Supported:
|
|---|
| 37 | * SMART feature set
|
|---|
| 38 | Security Mode feature set
|
|---|
| 39 | * Power Management feature set
|
|---|
| 40 | * Write cache
|
|---|
| 41 | * Look-ahead
|
|---|
| 42 | * Host Protected Area feature set
|
|---|
| 43 | * WRITE_BUFFER command
|
|---|
| 44 | * READ_BUFFER command
|
|---|
| 45 | * NOP cmd
|
|---|
| 46 | * DOWNLOAD_MICROCODE
|
|---|
| 47 | Power-Up In Standby feature set
|
|---|
| 48 | * SET_FEATURES required to spinup after power up
|
|---|
| 49 | SET_MAX security extension
|
|---|
| 50 | * 48-bit Address feature set
|
|---|
| 51 | * Device Configuration Overlay feature set
|
|---|
| 52 | * Mandatory FLUSH_CACHE
|
|---|
| 53 | * FLUSH_CACHE_EXT
|
|---|
| 54 | * SMART error logging
|
|---|
| 55 | * SMART self-test
|
|---|
| 56 | * General Purpose Logging feature set
|
|---|
| 57 | * 64-bit World wide name
|
|---|
| 58 | * IDLE_IMMEDIATE with UNLOAD
|
|---|
| 59 | * WRITE_UNCORRECTABLE_EXT command
|
|---|
| 60 | * {READ,WRITE}_DMA_EXT_GPL commands
|
|---|
| 61 | * Segmented DOWNLOAD_MICROCODE
|
|---|
| 62 | * Gen1 signaling speed (1.5Gb/s)
|
|---|
| 63 | * Gen2 signaling speed (3.0Gb/s)
|
|---|
| 64 | * Gen3 signaling speed (6.0Gb/s)
|
|---|
| 65 | * Native Command Queueing (NCQ)
|
|---|
| 66 | * Host-initiated interface power management
|
|---|
| 67 | * Phy event counters
|
|---|
| 68 | * Idle-Unload when NCQ is active
|
|---|
| 69 | * NCQ priority information
|
|---|
| 70 | * READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
|
|---|
| 71 | * DMA Setup Auto-Activate optimization
|
|---|
| 72 | Device-initiated interface power management
|
|---|
| 73 | * Software settings preservation
|
|---|
| 74 | * SMART Command Transport (SCT) feature set
|
|---|
| 75 | * SCT Write Same (AC2)
|
|---|
| 76 | * SCT Error Recovery Control (AC3)
|
|---|
| 77 | * SCT Features Control (AC4)
|
|---|
| 78 | * SCT Data Tables (AC5)
|
|---|
| 79 | unknown 206[12] (vendor specific)
|
|---|
| 80 | unknown 206[13] (vendor specific)
|
|---|
| 81 | * DOWNLOAD MICROCODE DMA command
|
|---|
| 82 | * WRITE BUFFER DMA command
|
|---|
| 83 | * READ BUFFER DMA command
|
|---|
| 84 |
|
|---|
| 85 | Checksum: correct
|
|---|
| 86 |
|
|---|
