1 | smartctl 6.6 2017-11-05 r4594 [x86_64-linux-5.2.0-2-amd64] (local build) |
---|
2 | Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org |
---|
3 | |
---|
4 | === START OF INFORMATION SECTION === |
---|
5 | Device Model: SanDisk SD8SBAT128G1002 |
---|
6 | Firmware Version: Z2317002 |
---|
7 | User Capacity: 128,035,676,160 bytes [128 GB] |
---|
8 | Sector Size: 512 bytes logical/physical |
---|
9 | Rotation Rate: Solid State Device |
---|
10 | Form Factor: 2.5 inches |
---|
11 | Device is: Not in smartctl database [for details use: -P showall] |
---|
12 | ATA Version is: ACS-2 T13/2015-D revision 3 |
---|
13 | SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) |
---|
14 | Local Time is: Sun Sep 1 23:48:46 2019 CST |
---|
15 | SMART support is: Available - device has SMART capability. |
---|
16 | SMART support is: Enabled |
---|
17 | AAM feature is: Unavailable |
---|
18 | APM level is: 254 (maximum performance) |
---|
19 | Rd look-ahead is: Enabled |
---|
20 | Write cache is: Enabled |
---|
21 | DSN feature is: Unavailable |
---|
22 | ATA Security is: Disabled, NOT FROZEN [SEC1] |
---|
23 | Wt Cache Reorder: Unavailable |
---|
24 | |
---|
25 | === START OF READ SMART DATA SECTION === |
---|
26 | SMART overall-health self-assessment test result: PASSED |
---|
27 | |
---|
28 | General SMART Values: |
---|
29 | Offline data collection status: (0x00) Offline data collection activity |
---|
30 | was never started. |
---|
31 | Auto Offline Data Collection: Disabled. |
---|
32 | Self-test execution status: ( 0) The previous self-test routine completed |
---|
33 | without error or no self-test has ever |
---|
34 | been run. |
---|
35 | Total time to complete Offline |
---|
36 | data collection: ( 120) seconds. |
---|
37 | Offline data collection |
---|
38 | capabilities: (0x11) SMART execute Offline immediate. |
---|
39 | No Auto Offline data collection support. |
---|
40 | Suspend Offline collection upon new |
---|
41 | command. |
---|
42 | No Offline surface scan supported. |
---|
43 | Self-test supported. |
---|
44 | No Conveyance Self-test supported. |
---|
45 | No Selective Self-test supported. |
---|
46 | SMART capabilities: (0x0002) Does not save SMART data before |
---|
47 | entering power-saving mode. |
---|
48 | Supports SMART auto save timer. |
---|
49 | Error logging capability: (0x01) Error logging supported. |
---|
50 | General Purpose Logging supported. |
---|
51 | Short self-test routine |
---|
52 | recommended polling time: ( 2) minutes. |
---|
53 | Extended self-test routine |
---|
54 | recommended polling time: ( 10) minutes. |
---|
55 | |
---|
56 | SMART Attributes Data Structure revision number: 1 |
---|
57 | Vendor Specific SMART Attributes with Thresholds: |
---|
58 | ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE |
---|
59 | 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 |
---|
60 | 9 Power_On_Hours -O--CK 229 100 000 - 229 |
---|
61 | 12 Power_Cycle_Count -O--CK 100 100 000 - 3769 |
---|
62 | 166 Unknown_Attribute -O--CK 100 100 000 - 107 |
---|
63 | 167 Unknown_Attribute -O--CK 100 100 000 - 0 |
---|
64 | 168 Unknown_Attribute -O--CK 100 100 000 - 162 |
---|
65 | 169 Unknown_Attribute -O--CK 100 100 000 - 116 |
---|
66 | 170 Unknown_Attribute -O--CK 100 100 000 - 0 |
---|
67 | 171 Unknown_Attribute -O--CK 100 100 000 - 0 |
---|
68 | 172 Unknown_Attribute -O--CK 100 100 000 - 0 |
---|
69 | 173 Unknown_Attribute -O--CK 100 100 --- - 140 |
---|
70 | 174 Unknown_Attribute -O--CK 100 100 000 - 203 |
---|
71 | 187 Reported_Uncorrect -O--CK 100 100 000 - 0 |
---|
72 | 194 Temperature_Celsius -O---K 079 100 000 - 21 (Min/Max 0/50) |
---|
73 | 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 4 |
---|
74 | 230 Unknown_SSD_Attribute -O--CK 100 100 000 - 1320 |
---|
75 | 232 Available_Reservd_Space PO--CK 100 100 004 - 100 |
---|
76 | 233 Media_Wearout_Indicator -O--CK 100 100 000 - 12261 |
---|
77 | 241 Total_LBAs_Written ----CK 253 253 000 - 2177 |
---|
78 | 242 Total_LBAs_Read ----CK 253 253 000 - 2324 |
---|
79 | ||||||_ K auto-keep |
---|
80 | |||||__ C event count |
---|
81 | ||||___ R error rate |
---|
82 | |||____ S speed/performance |
---|
83 | ||_____ O updated online |
---|
84 | |______ P prefailure warning |
---|
85 | |
---|
86 | General Purpose Log Directory Version 1 |
---|
87 | SMART Log Directory Version 1 [multi-sector log support] |
---|
88 | Address Access R/W Size Description |
---|
89 | 0x00 GPL,SL R/O 1 Log Directory |
---|
90 | 0x01 SL R/O 1 Summary SMART error log |
---|
91 | 0x02 SL R/O 1 Comprehensive SMART error log |
---|
92 | 0x03 GPL R/O 1 Ext. Comprehensive SMART error log |
---|
93 | 0x04 GPL,SL R/O 8 Device Statistics log |
---|
94 | 0x06 SL R/O 1 SMART self-test log |
---|
95 | 0x07 GPL R/O 1 Extended self-test log |
---|
96 | 0x10 GPL R/O 1 NCQ Command Error log |
---|
97 | 0x11 GPL R/O 1 SATA Phy Event Counters log |
---|
98 | 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log |
---|
99 | 0x80-0x9f GPL,SL R/W 16 Host vendor specific log |
---|
100 | |
---|
101 | Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. |
---|
102 | SMART Extended Comprehensive Error Log Version: 1 (1 sectors) |
---|
103 | Device Error Count: 4 |
---|
104 | CR = Command Register |
---|
105 | FEATR = Features Register |
---|
106 | COUNT = Count (was: Sector Count) Register |
---|
107 | LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 |
---|
108 | LH = LBA High (was: Cylinder High) Register ] LBA |
---|
109 | LM = LBA Mid (was: Cylinder Low) Register ] Register |
---|
110 | LL = LBA Low (was: Sector Number) Register ] |
---|
111 | DV = Device (was: Device/Head) Register |
---|
112 | DC = Device Control Register |
---|
113 | ER = Error register |
---|
114 | ST = Status register |
---|
115 | Powered_Up_Time is measured from power on, and printed as |
---|
116 | DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, |
---|
117 | SS=sec, and sss=millisec. It "wraps" after 49.710 days. |
---|
118 | |
---|
119 | Error 4 [3] occurred at disk power-on lifetime: 65535 hours (2730 days + 15 hours) |
---|
120 | When the command that caused the error occurred, the device was in a vendor specific state. |
---|
121 | |
---|
122 | After command completion occurred, registers were: |
---|
123 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
124 | -- -- -- == -- == == == -- -- -- -- -- |
---|
125 | ff -- ff ff ff ff ff ff ff ff ff ff ff |
---|
126 | |
---|
127 | Commands leading to the command that caused the error were: |
---|
128 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
129 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
130 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
131 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
132 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
133 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
134 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
135 | |
---|
136 | Error 3 [2] occurred at disk power-on lifetime: 65535 hours (2730 days + 15 hours) |
---|
137 | When the command that caused the error occurred, the device was in a vendor specific state. |
---|
138 | |
---|
139 | After command completion occurred, registers were: |
---|
140 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
141 | -- -- -- == -- == == == -- -- -- -- -- |
---|
142 | ff -- ff ff ff ff ff ff ff ff ff ff ff |
---|
143 | |
---|
144 | Commands leading to the command that caused the error were: |
---|
145 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
146 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
147 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
148 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
149 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
150 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
151 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
152 | |
---|
153 | Error 2 [1] occurred at disk power-on lifetime: 65535 hours (2730 days + 15 hours) |
---|
154 | When the command that caused the error occurred, the device was in a vendor specific state. |
---|
155 | |
---|
156 | After command completion occurred, registers were: |
---|
157 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
158 | -- -- -- == -- == == == -- -- -- -- -- |
---|
159 | ff -- ff ff ff ff ff ff ff ff ff ff ff |
---|
160 | |
---|
161 | Commands leading to the command that caused the error were: |
---|
162 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
163 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
164 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
165 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
166 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
167 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
168 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
169 | |
---|
170 | Error 1 [0] occurred at disk power-on lifetime: 65535 hours (2730 days + 15 hours) |
---|
171 | When the command that caused the error occurred, the device was in a vendor specific state. |
---|
172 | |
---|
173 | After command completion occurred, registers were: |
---|
174 | ER -- ST COUNT LBA_48 LH LM LL DV DC |
---|
175 | -- -- -- == -- == == == -- -- -- -- -- |
---|
176 | ff -- ff ff ff ff ff ff ff ff ff ff ff |
---|
177 | |
---|
178 | Commands leading to the command that caused the error were: |
---|
179 | CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name |
---|
180 | -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- |
---|
181 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
182 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
183 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
184 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
185 | ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC] |
---|
186 | |
---|
187 | SMART Extended Self-test Log Version: 1 (1 sectors) |
---|
188 | Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error |
---|
189 | # 1 Short offline Completed without error 00% 229 - |
---|
190 | |
---|
191 | Selective Self-tests/Logging not supported |
---|
192 | |
---|
193 | SCT Commands not supported |
---|
194 | |
---|
195 | Device Statistics (GP Log 0x04) |
---|
196 | Page Offset Size Value Flags Description |
---|
197 | 0x01 ===== = = === == General Statistics (rev 1) == |
---|
198 | 0x01 0x008 4 3769 --- Lifetime Power-On Resets |
---|
199 | 0x01 0x018 6 0 --- Logical Sectors Written |
---|
200 | 0x01 0x020 6 0 --- Number of Write Commands |
---|
201 | 0x01 0x028 6 0 --- Logical Sectors Read |
---|
202 | 0x01 0x030 6 0 --- Number of Read Commands |
---|
203 | 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |
---|
204 | 0x07 0x008 1 4 --- Percentage Used Endurance Indicator |
---|
205 | |||_ C monitored condition met |
---|
206 | ||__ D supports DSN |
---|
207 | |___ N normalized value |
---|
208 | |
---|
209 | Pending Defects log (GP Log 0x0c) not supported |
---|
210 | |
---|
211 | SATA Phy Event Counters (GP Log 0x11) |
---|
212 | ID Size Value Description |
---|
213 | 0x0001 4 0 Command failed due to ICRC error |
---|
214 | 0x0002 4 0 R_ERR response for data FIS |
---|
215 | 0x0005 4 0 R_ERR response for non-data FIS |
---|
216 | 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET |
---|
217 | |
---|