1 | smartctl 6.5 2016-05-07 r4318 [x86_64-linux-3.10.0-862.el7.x86_64] (local build) |
---|
2 | Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org |
---|
3 | |
---|
4 | === START OF INFORMATION SECTION === |
---|
5 | Device Model: ST12000NM0007-2A1101 |
---|
6 | Firmware Version: SN02 |
---|
7 | User Capacity: 12,000,138,625,024 bytes [12.0 TB] |
---|
8 | Sector Sizes: 512 bytes logical, 4096 bytes physical |
---|
9 | Rotation Rate: 7200 rpm |
---|
10 | Form Factor: 3.5 inches |
---|
11 | Device is: Not in smartctl database [for details use: -P showall] |
---|
12 | ATA Version is: ACS-3 T13/2161-D revision 5 |
---|
13 | SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) |
---|
14 | Local Time is: Fri Jun 15 17:15:13 2018 CEST |
---|
15 | SMART support is: Available - device has SMART capability. |
---|
16 | SMART support is: Enabled |
---|
17 | AAM feature is: Unavailable |
---|
18 | APM feature is: Unavailable |
---|
19 | Rd look-ahead is: Enabled |
---|
20 | Write cache is: Enabled |
---|
21 | ATA Security is: Disabled, frozen [SEC2] |
---|
22 | Write SCT (Get) Feature Control Command failed: scsi error badly formed scsi parameters |
---|
23 | Wt Cache Reorder: Unknown (SCT Feature Control command failed) |
---|
24 | |
---|
25 | === START OF READ SMART DATA SECTION === |
---|
26 | SMART overall-health self-assessment test result: PASSED |
---|
27 | |
---|
28 | General SMART Values: |
---|
29 | Offline data collection status: (0x82) Offline data collection activity |
---|
30 | was completed without error. |
---|
31 | Auto Offline Data Collection: Enabled. |
---|
32 | Self-test execution status: ( 0) The previous self-test routine completed |
---|
33 | without error or no self-test has ever |
---|
34 | been run. |
---|
35 | Total time to complete Offline |
---|
36 | data collection: ( 567) seconds. |
---|
37 | Offline data collection |
---|
38 | capabilities: (0x7b) SMART execute Offline immediate. |
---|
39 | Auto Offline data collection on/off support. |
---|
40 | Suspend Offline collection upon new |
---|
41 | command. |
---|
42 | Offline surface scan supported. |
---|
43 | Self-test supported. |
---|
44 | Conveyance Self-test supported. |
---|
45 | Selective Self-test supported. |
---|
46 | SMART capabilities: (0x0003) Saves SMART data before entering |
---|
47 | power-saving mode. |
---|
48 | Supports SMART auto save timer. |
---|
49 | Error logging capability: (0x01) Error logging supported. |
---|
50 | General Purpose Logging supported. |
---|
51 | Short self-test routine |
---|
52 | recommended polling time: ( 1) minutes. |
---|
53 | Extended self-test routine |
---|
54 | recommended polling time: (1075) minutes. |
---|
55 | Conveyance self-test routine |
---|
56 | recommended polling time: ( 2) minutes. |
---|
57 | SCT capabilities: (0x70bd) SCT Status supported. |
---|
58 | SCT Error Recovery Control supported. |
---|
59 | SCT Feature Control supported. |
---|
60 | SCT Data Table supported. |
---|
61 | |
---|
62 | SMART Attributes Data Structure revision number: 10 |
---|
63 | Vendor Specific SMART Attributes with Thresholds: |
---|
64 | ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE |
---|
65 | 1 Raw_Read_Error_Rate POSR-- 080 068 044 - 97462749 |
---|
66 | 3 Spin_Up_Time PO---- 093 093 000 - 0 |
---|
67 | 4 Start_Stop_Count -O--CK 100 100 020 - 6 |
---|
68 | 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 |
---|
69 | 7 Seek_Error_Rate POSR-- 062 060 045 - 1716253 |
---|
70 | 9 Power_On_Hours -O--CK 100 100 000 - 7 |
---|
71 | 10 Spin_Retry_Count PO--C- 100 100 097 - 0 |
---|
72 | 12 Power_Cycle_Count -O--CK 100 100 020 - 7 |
---|
73 | 187 Reported_Uncorrect -O--CK 100 100 000 - 0 |
---|
74 | 188 Command_Timeout -O--CK 100 100 000 - 0 |
---|
75 | 190 Airflow_Temperature_Cel -O---K 063 052 040 - 37 (Min/Max 28/38) |
---|
76 | 192 Power-Off_Retract_Count -O--CK 100 100 000 - 2 |
---|
77 | 193 Load_Cycle_Count -O--CK 100 100 000 - 15 |
---|
78 | 194 Temperature_Celsius -O---K 037 040 000 - 37 (0 26 0 0 0) |
---|
79 | 195 Hardware_ECC_Recovered -O-RC- 080 068 000 - 97462749 |
---|
80 | 197 Current_Pending_Sector -O--C- 100 100 000 - 0 |
---|
81 | 198 Offline_Uncorrectable ----C- 100 100 000 - 0 |
---|
82 | 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 |
---|
83 | 200 Multi_Zone_Error_Rate PO---K 100 100 001 - 0 |
---|
84 | 240 Head_Flying_Hours ------ 100 253 000 - 5 (190 36 0) |
---|
85 | 241 Total_LBAs_Written ------ 100 253 000 - 1053501060 |
---|
86 | 242 Total_LBAs_Read ------ 100 253 000 - 4425069676 |
---|
87 | ||||||_ K auto-keep |
---|
88 | |||||__ C event count |
---|
89 | ||||___ R error rate |
---|
90 | |||____ S speed/performance |
---|
91 | ||_____ O updated online |
---|
92 | |______ P prefailure warning |
---|
93 | |
---|
94 | General Purpose Log Directory Version 1 |
---|
95 | SMART Log Directory Version 1 [multi-sector log support] |
---|
96 | Address Access R/W Size Description |
---|
97 | 0x00 GPL,SL R/O 1 Log Directory |
---|
98 | 0x01 SL R/O 1 Summary SMART error log |
---|
99 | 0x02 SL R/O 5 Comprehensive SMART error log |
---|
100 | 0x03 GPL R/O 5 Ext. Comprehensive SMART error log |
---|
101 | 0x04 GPL R/O 256 Device Statistics log |
---|
102 | 0x04 SL R/O 8 Device Statistics log |
---|
103 | 0x06 SL R/O 1 SMART self-test log |
---|
104 | 0x07 GPL R/O 1 Extended self-test log |
---|
105 | 0x08 GPL R/O 2 Power Conditions log |
---|
106 | 0x09 SL R/W 1 Selective self-test log |
---|
107 | 0x0c GPL R/O 2048 Pending Defects log |
---|
108 | 0x10 GPL R/O 1 SATA NCQ Queued Error log |
---|
109 | 0x11 GPL R/O 1 SATA Phy Event Counters log |
---|
110 | 0x13 GPL R/O 1 SATA NCQ Send and Receive log |
---|
111 | 0x15 GPL R/W 1 SATA Rebuild Assist log |
---|
112 | 0x21 GPL R/O 1 Write stream error log |
---|
113 | 0x22 GPL R/O 1 Read stream error log |
---|
114 | 0x24 GPL R/O 768 Current Device Internal Status Data log |
---|
115 | 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log |
---|
116 | 0x80-0x9f GPL,SL R/W 16 Host vendor specific log |
---|
117 | 0xa1 GPL,SL VS 24 Device vendor specific log |
---|
118 | 0xa2 GPL VS 16320 Device vendor specific log |
---|
119 | 0xa4 GPL,SL VS 160 Device vendor specific log |
---|
120 | 0xa6 GPL VS 192 Device vendor specific log |
---|
121 | 0xa8-0xa9 GPL,SL VS 136 Device vendor specific log |
---|
122 | 0xab GPL VS 1 Device vendor specific log |
---|
123 | 0xad GPL VS 16 Device vendor specific log |
---|
124 | 0xbe-0xbf GPL VS 65535 Device vendor specific log |
---|
125 | 0xc1 GPL,SL VS 8 Device vendor specific log |
---|
126 | 0xc3 GPL,SL VS 32 Device vendor specific log |
---|
127 | 0xc9 GPL,SL VS 8 Device vendor specific log |
---|
128 | 0xca GPL,SL VS 16 Device vendor specific log |
---|
129 | 0xd1 GPL VS 336 Device vendor specific log |
---|
130 | 0xd2 GPL VS 10000 Device vendor specific log |
---|
131 | 0xd4 GPL VS 2048 Device vendor specific log |
---|
132 | 0xda GPL,SL VS 1 Device vendor specific log |
---|
133 | 0xe0 GPL,SL R/W 1 SCT Command/Status |
---|
134 | 0xe1 GPL,SL R/W 1 SCT Data Transfer |
---|
135 | |
---|
136 | SMART Extended Comprehensive Error Log Version: 1 (5 sectors) |
---|
137 | No Errors Logged |
---|
138 | |
---|
139 | SMART Extended Self-test Log Version: 1 (1 sectors) |
---|
140 | Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error |
---|
141 | # 1 Short offline Completed without error 00% 7 - |
---|
142 | |
---|
143 | SMART Selective self-test log data structure revision number 1 |
---|
144 | SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS |
---|
145 | 1 0 0 Not_testing |
---|
146 | 2 0 0 Not_testing |
---|
147 | 3 0 0 Not_testing |
---|
148 | 4 0 0 Not_testing |
---|
149 | 5 0 0 Not_testing |
---|
150 | Selective self-test flags (0x0): |
---|
151 | After scanning selected spans, do NOT read-scan remainder of disk. |
---|
152 | If Selective self-test is pending on power-up, resume after 0 minute delay. |
---|
153 | |
---|
154 | SCT Status Version: 3 |
---|
155 | SCT Version (vendor specific): 522 (0x020a) |
---|
156 | SCT Support Level: 1 |
---|
157 | Device State: Active (0) |
---|
158 | Current Temperature: 37 Celsius |
---|
159 | Power Cycle Min/Max Temperature: 28/38 Celsius |
---|
160 | Lifetime Min/Max Temperature: 22/48 Celsius |
---|
161 | Under/Over Temperature Limit Count: 0/0 |
---|
162 | |
---|
163 | SCT Temperature History Version: 2 |
---|
164 | Temperature Sampling Period: 3 minutes |
---|
165 | Temperature Logging Interval: 59 minutes |
---|
166 | Min/Max recommended Temperature: 10/40 Celsius |
---|
167 | Min/Max Temperature Limit: 5/60 Celsius |
---|
168 | Temperature History Size (Index): 128 (20) |
---|
169 | |
---|
170 | Index Estimated Time Temperature Celsius |
---|
171 | 21 2018-06-10 12:05 ? - |
---|
172 | ... ..(105 skipped). .. - |
---|
173 | 127 2018-06-14 20:19 ? - |
---|
174 | 0 2018-06-14 21:18 48 ***************************** |
---|
175 | 1 2018-06-14 22:17 ? - |
---|
176 | 2 2018-06-14 23:16 22 *** |
---|
177 | 3 2018-06-15 00:15 ? - |
---|
178 | 4 2018-06-15 01:14 25 ****** |
---|
179 | 5 2018-06-15 02:13 ? - |
---|
180 | 6 2018-06-15 03:12 25 ****** |
---|
181 | 7 2018-06-15 04:11 ? - |
---|
182 | 8 2018-06-15 05:10 27 ******** |
---|
183 | 9 2018-06-15 06:09 ? - |
---|
184 | 10 2018-06-15 07:08 27 ******** |
---|
185 | 11 2018-06-15 08:07 ? - |
---|
186 | 12 2018-06-15 09:06 29 ********** |
---|
187 | 13 2018-06-15 10:05 ? - |
---|
188 | 14 2018-06-15 11:04 28 ********* |
---|
189 | 15 2018-06-15 12:03 37 ****************** |
---|
190 | 16 2018-06-15 13:02 37 ****************** |
---|
191 | 17 2018-06-15 14:01 37 ****************** |
---|
192 | 18 2018-06-15 15:00 38 ******************* |
---|
193 | 19 2018-06-15 15:59 37 ****************** |
---|
194 | 20 2018-06-15 16:58 37 ****************** |
---|
195 | |
---|
196 | SCT Error Recovery Control: |
---|
197 | Read: 100 (10.0 seconds) |
---|
198 | Write: 100 (10.0 seconds) |
---|
199 | |
---|
200 | Device Statistics (GP/SMART Log 0x04) not supported |
---|
201 | |
---|
202 | SATA Phy Event Counters (GP Log 0x11) |
---|
203 | ID Size Value Description |
---|
204 | 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET |
---|
205 | 0x0001 2 0 Command failed due to ICRC error |
---|
206 | 0x0003 2 0 R_ERR response for device-to-host data FIS |
---|
207 | 0x0004 2 0 R_ERR response for host-to-device data FIS |
---|
208 | 0x0006 2 0 R_ERR response for device-to-host non-data FIS |
---|
209 | 0x0007 2 0 R_ERR response for host-to-device non-data FIS |
---|
210 | |
---|