1 | smartctl 6.6 2016-05-31 r4324 [armv7l-linux-4.14.22-v7+] (local build)
|
---|
2 | Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
|
---|
3 |
|
---|
4 | === START OF INFORMATION SECTION ===
|
---|
5 | Device Model: WDC WD3750LMCW-11D9GS3
|
---|
6 | Serial Number: WD-WXQ1E365E1U0
|
---|
7 | LU WWN Device Id: 5 0014ee 65c794845
|
---|
8 | Firmware Version: 01.01A01
|
---|
9 | User Capacity: 375,083,606,016 bytes [375 GB]
|
---|
10 | Sector Sizes: 512 bytes logical, 4096 bytes physical
|
---|
11 | Rotation Rate: 5400 rpm
|
---|
12 | Form Factor: 2.5 inches
|
---|
13 | Device is: Not in smartctl database [for details use: -P showall]
|
---|
14 | ATA Version is: ACS-3 T13/2161-D revision 5
|
---|
15 | SATA Version is: SATA 3.1, 1.5 Gb/s (current: 1.5 Gb/s)
|
---|
16 | Local Time is: Sun Mar 11 16:28:30 2018 EDT
|
---|
17 | SMART support is: Available - device has SMART capability.
|
---|
18 | SMART support is: Enabled
|
---|
19 |
|
---|
20 | === START OF READ SMART DATA SECTION ===
|
---|
21 | SMART overall-health self-assessment test result: PASSED
|
---|
22 |
|
---|
23 | General SMART Values:
|
---|
24 | Offline data collection status: (0x80) Offline data collection activity
|
---|
25 | was never started.
|
---|
26 | Auto Offline Data Collection: Enabled.
|
---|
27 | Self-test execution status: ( 0) The previous self-test routine completed
|
---|
28 | without error or no self-test has ever
|
---|
29 | been run.
|
---|
30 | Total time to complete Offline
|
---|
31 | data collection: ( 8820) seconds.
|
---|
32 | Offline data collection
|
---|
33 | capabilities: (0x7b) SMART execute Offline immediate.
|
---|
34 | Auto Offline data collection on/off support.
|
---|
35 | Suspend Offline collection upon new
|
---|
36 | command.
|
---|
37 | Offline surface scan supported.
|
---|
38 | Self-test supported.
|
---|
39 | Conveyance Self-test supported.
|
---|
40 | Selective Self-test supported.
|
---|
41 | SMART capabilities: (0x0003) Saves SMART data before entering
|
---|
42 | power-saving mode.
|
---|
43 | Supports SMART auto save timer.
|
---|
44 | Error logging capability: (0x01) Error logging supported.
|
---|
45 | General Purpose Logging supported.
|
---|
46 | Short self-test routine
|
---|
47 | recommended polling time: ( 2) minutes.
|
---|
48 | Extended self-test routine
|
---|
49 | recommended polling time: ( 102) minutes.
|
---|
50 | Conveyance self-test routine
|
---|
51 | recommended polling time: ( 5) minutes.
|
---|
52 | SCT capabilities: (0x3035) SCT Status supported.
|
---|
53 | SCT Feature Control supported.
|
---|
54 | SCT Data Table supported.
|
---|
55 |
|
---|
56 | SMART Attributes Data Structure revision number: 16
|
---|
57 | Vendor Specific SMART Attributes with Thresholds:
|
---|
58 | ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
|
---|
59 | 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
|
---|
60 | 3 Spin_Up_Time 0x0027 116 108 021 Pre-fail Always - 3158
|
---|
61 | 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 32
|
---|
62 | 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
|
---|
63 | 7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
|
---|
64 | 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 16
|
---|
65 | 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
|
---|
66 | 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
|
---|
67 | 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 8
|
---|
68 | 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 2
|
---|
69 | 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 1115
|
---|
70 | 194 Temperature_Celsius 0x0022 111 104 000 Old_age Always - 32
|
---|
71 | 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
|
---|
72 | 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
|
---|
73 | 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
|
---|
74 | 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
|
---|
75 | 200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
|
---|
76 |
|
---|
77 | SMART Error Log Version: 1
|
---|
78 | No Errors Logged
|
---|
79 |
|
---|
80 | SMART Self-test log structure revision number 1
|
---|
81 | No self-tests have been logged. [To run self-tests, use: smartctl -t]
|
---|
82 |
|
---|
83 | SMART Selective self-test log data structure revision number 1
|
---|
84 | SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
|
---|
85 | 1 0 0 Not_testing
|
---|
86 | 2 0 0 Not_testing
|
---|
87 | 3 0 0 Not_testing
|
---|
88 | 4 0 0 Not_testing
|
---|
89 | 5 0 0 Not_testing
|
---|
90 | Selective self-test flags (0x0):
|
---|
91 | After scanning selected spans, do NOT read-scan remainder of disk.
|
---|
92 | If Selective self-test is pending on power-up, resume after 0 minute delay.
|
---|